vizpin LH-LHR Powered Mortise Lock Instruction Manual

vizpin LH-LHR Powered Mortise Lock

Specifications:

• Product Name: VIZpin Powered Mortise Lock
• Model: MRS
• Handing: LH/LHR, RH/RHR
• Manufacturer Contact for Mechanical Concerns: Phone 866-874-3662, Website: www.pdqlocks.com
• Manufacturer Contact for Electrical Concerns: Email: Support@VIZpin.com, Website: www.VIZpin.com

Product Usage Instructions

1. CHECK HANDING OF LOCK BODY: Ensure the correct handing of the lock body before proceeding.
2. DOOR PREPARATION: Use the hardware kit W51411 to prepare the door, including installing the Dead Latch Slider.
3. JAMB PREPARATION: Prepare the jamb using the strike screw pack.
4. LEVER ATTACHMENT: Assemble the rose with the lever according to instructions. For Orlando/Memphis Levers & Ball Knob, follow specific instructions.
5. INSTALL DRIVE SPINDLES / OUTSIDE TRIM: Install drive spindles and outside trim, ensuring proper operation of the latch.
6. INSTALL INSIDE TRIM / ROSE: Attach the inside trim and rose, securing them using machine screws from the hardware kit.
7. CYLINDER, TURNPIECE AND ARMOR PLATE INSTALLATION: Install these components as per the provided instructions.
8. INSIDE MOUNTING PLATE ASSEMBLY: Install the inside mounting plate assembly securely.
9. INSTALL BATTERY PACK: Connect the battery wire to the control board and snap the battery pack onto the retainers on the mounting plate.
10. INSTALL BATTERIES AND BATTERY COVER: Insert batteries and secure the battery cover with black pan head screws.

MRS INSTALLATION INSTRUCTIONS VIZPIN POWERED MORTISE LOCK

For Mechanical Concerns:
Phone: 866 874 3662
www.pdqlocks.com

For Electrical Concerns:
Email: Support@VIZpin.com
www.VIZpin.com

CHECK HANDING OF LOCK BODY

• If handing of lock body is not correct for opening, consult factory for handing instruction.

DOOR PREPARATION

• Prepare the door for the mortise lock.
• Install the mortise case while feeding chassis wire into hole on inside of door.
• Gently pull wire through hole as chassis is inserted
• Secure using two (2) combo screws supplied in the hardware kit, W51411

JAMB PREPARATION

• Prepare the jamb for the mortise lock strike.
• Install Dead Latch Plate behind strike with slider toward bottom for dead latch.
• Install the strike and secure with two (2) combo screws supplied in the strike screw pack

LEVER ATTACHMENT

• Assembly Outside Lever If outside scalp was removed, install scalp.
  Assemble rose as shown using the supplied hex key to tighten the socket head cap screw.
  Orlando/Memphis Levers & Ball Knob Skip the following step. Do not install inside lever and discard one (1) socket head cap screw. Refer to step 6.

• Assembly Inside Lever Remove inside scalp. Assemble the inside rose as shown using the supplied hex key to tighten the socket head cap screw.

INSTALL DRIVE SPINDLES / OUTSIDE TRIM

Drive Spindles:

• Install drive spindles and springs on both sides in orientation shown.

Outside Trim

• Install outside trim to door while aligning lever with drive spindle.
• Confirm spindle engagement in lock by rotating the lever down,retracting the latch.

MRS STS – MORTISE LOCK

INSTALL INSIDE TRIM / ROSE

• Install the inside rose assembly to the inside of the door. Align the spindle with the lever.

• Secure inside rose assembly with 1-1/2″ long flat head machine screws, supplied in the hardware kit, W51411 – Confirm the spindle engagement.

• Install the rose scalp by aligning the dimples with the slots in the rose plate. Secure by rotating clockwise until tight.
  FOR ORLANDO/MEMPHIS LEVERS & BALL KNOB

• Slide lever onto spindle. Install set screw in bottom of lever.
  Tighten from underside with supplied hex key.

CYLINDER, TURNPIECE AND ARMOR PLATE INSTALLATION

• Assembly cylinder, cylinder spring and cylinder trim collar.

• Thread the cylinder into the lock body until the cylinder is flush or slightly recessed in the cylinder trim collar.

• Secure the cylinder by tightening set screw through front of case,on the side of cylinder, with the hex key provided in the hardware kit, W51411.
  For I/C housings, install the slotted set screw through the I/C bore to secure the housing.

• Install the turnpiece and secure with two (2) truss head sheet metal screws, supplied in the thumb turn screw pack.

• Install the armor plate with two (2) flat head machine screws.

INSTALL INSIDE MOUNTING PLATE ASSEMBLY

• Install inside mounting plate assembly.
• Feed chassis wire through T slot in mounting plate.
• Secure with (4) pan head wood/metal screws.
• Make wire connection after reader is secure. Push extra wire into door cavity.

MRS STS MORTISE LOCK

INSTALL BATTERY PACK

• Plug in battery wire to control board.
• Install battery pack over two studs on mounting plate.
• Snap battery pack onto retainers on mounting plate.

INSTALL BATTERIES AND BATTERY COVER

• Install batteries and battery cover with (2) black pan head

Frequently Asked Questions (FAQ)

How do I determine the correct handing of the lock body?

Refer to the user manual or contact customer support for assistance in determining the correct handing based on your door setup.

What should I do if I encounter difficulties during lever attachment?

Double-check the assembly steps and ensure all components are aligned properly. If issues persist, contact customer support for guidance.

How often should I replace the batteries in the lock?

It is recommended to replace the batteries periodically or when low battery warnings are indicated to ensure continuous operation of the lock.

References

• Smartphone Access Control Systems - Keyless Entry (Bluetooth) | VIZpin

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>