K-ARRAY KA208 2RU Digital Processing Multi Channel Amplifiers User Guide
- June 9, 2024
- K-ARRAY
Table of Contents
Kommander-KA
2RU Digital Processing Multi-Channel Amplifiers
USER GUIDE
Kommander-KA
User Guide
IMPORTANT SAFETY INSTRUCTIONS
ATTENTION CAUTION
DO NOT OPEN
ATTENTION: CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol alerts the user to the presence of recommendations about the
product’s use and maintenance.
The lighting flash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of uninsulated, dangerous
voltage within the product enclosure that may be of magnitude to constitute a
risk of electrical shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in this guide.
Operator’s manual; operating instructions This symbol identifies the
operator’s manual that relates to the operating instructions and indicates
that the operating instructions
should be considered when operating the device or control close to where the
symbol is placed.
For indoor use only
This electrical equipment is designed primarily for indoor use.
WEEE
Please dispose of this product at the end of its operational lifetime by
bringing it to your local collection point or recycling center for such
equipment.
This device complies with Restriction of Hazardous Substances Directive.
WARNING
Failure to follow these safety instructions could result in fire, shock or
other injury or damage to the device or other property.
General heed and warnings
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water.
-
Clean only with dry cloth.
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat
-
Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
-
Only use attachments/accessories specified by the manufacturer.
-
Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus.
-
Clean the product only with a soft and dry fabric. Never use liquid cleaning products, as this may damage the products cosmetic surfaces.
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
-
Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Avoid placing the product in a location under direct sunlight or near any appliance that generates UV (Ultra Violet) light, as this may change the product surface finishing and cause a change in color.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
-
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so. -
WARNING: Only use attachments/accessories specified or provided by the manufacturer (such as the exclusive supply adapter, battery, etc.).
This apparatus is intended for professional use.
Installation and commissioning may only be carried out by qualified and
authorized personnel.
- Before turning the power on or off for all devices, set all volume levels to minimum.
- Use only speaker cables for connecting speakers to the speaker terminals. Be sure to observe the amplifier’s rated load impedance particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier’s rated range can damage the apparatus.
- K-array cannot be held responsible for damage caused by improper use of the loudspeakers.
- K-array will not shoulder any responsibilities for products modified without prior authorization.
CE Statement
K-array declares that this device is in compliance with applicable CE
standards and regulations. Before putting the device into operation, please
observe the respective country-specific regulations!
FCC Statement
**** This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment must be installed and operated in
accordance with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
CAUTION! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Canadian Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian
information on RF exposure and compliance.
This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Trademark Notice
All trademarks are the property of their respective owners.
Thank you for choosing this K-array product!
To ensure proper operation, please carefully read the owner’s manuals and
safety instruction before using the products. After reading this manual, be
sure to keep it for future reference.
Should you have any questions about your new device please contact K-array
customer service at support@k-array.com or
contact the official K-array distributor in your country.
Kommander-KA is the line of K-array amplifiers meticulously designed and built
with powerful DSPs and Class D amp modules that extend the sound experience
through intelligent sound processing that can adapt to any context.
Each amplifier of the Kommander-KA line is fully loaded on board with all the
configurations necessary to drive any K-array passive product to fulfill
maximum power of each output channel, of course a variety of power differ from
model to model to give you a wider choice for specific applications.
The K-array Connect mobile app and K-framework software provide the control
dashboards to access all Kommander-KA DSP features for system settings, fine
tuning and monitoring in single unit installations and demanding applications
where thousands of watts must be carefully managed.
Unpacking
Each K-array amplifier is built to the highest standard and thoroughly
inspected before leaving the factory.
Upon arrival, carefully inspect the shipping carton, then examine and test
your new amplifier. If you find any damage, immediately notify the shipping
company. Check that the following parts are supplied with the product.
A. 1x Amplifier unit: model and version shall be one from the following list:
- Kommander-KA14 I
- Kommander-KA18
- Kommander-KA28
- Kommander-KA34
- Kommander-KA68
- Kommander-KA104
- Kommander-KA208
B. 2x Rack mounting brackets with screws
C. PC 4/ 4-ST-7,62 speaker output flying connectors *
D. 1x Power cord
E. 1x The quick guide
Notes
- 2 pieces in 4-channel units, 4 pieces in 8-channel units.
** The AC mains cord plug may differ from the picture according to local regulation.
Introduction
The Kommander-KA amplifiers are available in two versions: 4-channel units and 8-channel units. Both versions implement multichannel free routing and DSP with Grouping, Input EQ, Output EQ, Level adjustment, Dynamic Limiters and Delay per channel.
| 4-channel units | Connectors | Power Rating per channel |
|---|---|---|
| Kommander-KA14 I | input | output |
| Kommander-KA34 | 4 | 4 |
| Kommander-KA104 | 4 | 4 |
| 4 | 4 |
8-channel units
Kommander-KA18| 8| 8| 150W @ 4Ω
Kommander-KA28| 8| 8| 600W @ 2Ω
Kommander-KA68| 8| 8| 750W @ 4Ω
Kommander-KA208| 8| 8| 2500W @ 4Ω
The dedicated K-array Connect app and the K-framework3 software for Mac and PC allow user access to the highly configurable output section and the powerful DSP making any Kommander-KA amplifier a flexible driving unit. In order to remote control a Kommander-KA amplifier download the K-array Connect app or the K-framework3 software:
|
---|---
http://software.k-array.com/connect/store|
https://www.k-array.com/en/software/
Getting Started
-
Connect the input and output signal cables according to the configuration you want to achieve.
-
Connect the Kommander-KA02 I to its power supply and plug the power cord to the AC mains socket.
-
Use the K-array Connect app to connect your mobile device to the Kommander amplifier unit
-
Set the amplifier Output Configuration*: the Devices menu will show the device(s) you can manage with the app: press on the image of the unit to configure.
**** Carefully check that the factory presets match the actual configuration of passive speakers connected to the amplifier connectors. -
Set the signal routing from the input channels to the output channels in the ROUTING tab.
-
Check the signal volume in the VOLUMES tab.
-
Enjoy K-array sound!
Mounting and cooling
K-array Kommander amplifiers are provided with a couple of brackets for common 19” rack installation: each Kommander amplifier occupies 2 rack units. In order to set the amplifier for rack installation:
- unscrew the four bottom feet;
- assemble the lateral rack mounting brackets with screws provided within the package.
In order to prevent any mechanical issue, use both frontal and rear mounting
brackets to secure the amplifier to its location.
Install the amplifier in a well-ventilated location at 35°C (95°F) max
environment temperature.
The ventilation openings must not be impeded by any item. Fresh air enter the
amplifier from aside, warm air is expelled under the front panel.
In rack mount installation leave one rack unit empty every three installed
amplifiers to guarantee adequate air flow.
4-channel Amplifier Rear Panel
- Status LED
- Reset button
- 4x XLR-F balanced line channel inputs
- USB ports
- 2x PC 4/ 4-ST-7,62 speaker output terminals
- PowerCon TRUE link (AC mains out)
- PowerCon TRUE inlet (AC mains in)
- QR Code for the K-array Connect app remote connection
- RJ45 Ethernet port
- 4x XLR-M balanced line channel outputs
8-channel Amplifier Rear Panel
A. Status LED
B. Reset button
C. 4x XLR-F balanced line channel 1, 2, 3 and 4 inputs
D. USB ports
E. 4x PC 4/ 4-ST-7,62 speaker output terminals
F. PowerCon TRUE link (AC mains out)
G. PowerCon TRUE inlet (AC mains in)
H. QR Code for the K-array Connect app remote connection
I. RJ45 Ethernet port
J. 4x XLR-M balanced line channel 5, 6, 7 and 8 inputs
Front Panel
A. Input signal monitor LED
B. Output signal monitor LED
C. Status LED
D. Standby button
AC mains supply
The AC Main connection is made via the provided power cord:
- insert the powerCon TRUE flying connector into the inlet and then rotate it clockwise;
- connect the power plug of the power cord to a mains socket outlet.
Once properly plugged, the amplifier power up: the front and back LEDs light on.
In order to set the amplifier unit in standby mode, keep pressed the button on the front panel for 2 seconds. Keep pressed the button for 2 seconds to wake up the amplifier from standby mode. The powerCon TRUE link (AC mains out) connector allows to distribute the AC main power to other units according to their power consumption. Please don’t exceed the limits stated on the next tables.
| **Power consumption*| Max number of cascade
powered equal units**
---|---|---
Kommander-KA14 I| 400 W| 4x KA14 I
Kommander-KA34| 600 W| 4x KA34
Kommander-KA104| 1200 W| 2x KA104
Kommander-KA18| 300 W| 6x KA18
Kommander-KA28| 800 W| 2x KA28
Kommander-KA68| 1200 W| 2x KA28
Kommander-KA208| 1200 W| –
- Power Consumption at 4 Ω load, Pink noise, 1/8 rated power.
LED chart
In the rear panel, the input signal monitor LED and the output signal monitor LED blink according to the presence of audio signal at any input or output channel respectively. The input and output signal monitor LEDs light on orange when the DSP is limiting the signal level.
Status LED
| Color| Mode| Description
---|---|---|---
| orange| solid| DSP software is loading
| green| solid| System ready
| blue| solid| User command: system identification
| purple| flashing| Network parameters reset
Input Wiring
Kommander-KA amplifiers accept balanced input signals. Only high quality
balanced, screened, twisted pair audio cables with metal XLR connectors should
be used.
**** The amplifier input sensitivity is set to accept input signal at +4 dBu
reference level.
IN: Line input audio connector.
Male XLR plug and female XLR chassis connector. Pinouts:
- ground
- hot
- cold.
LINK (4-channel amplifiers only): audio connector phisically paralleled to the
corresponding input connector.
Female XLR plug and male XLR chassis connector. Pinouts:
- ground
- hot
- cold.
Loudspeakers Wiring
In order to set the proper connections with the loudspeakers, a set of
euroblock PC 4/4-ST-7,62 flying connectors are provided.
Each PC 4/4-ST-7,62 flying connector features four terminals designed to be
connected to a couple of loudspeaker cables (carrying two wires each). Be sure
to observe the correct polarity at both the loudspeaker and amplifier cable
ends. 
When connecting multiple loudspeakers in parallel to the same amplifier’s output channel, make sure the total nominal impedance doesn’t lower under the amplifier minimum recommended load impedance.
| Minimum Load| Power Rating per channel at minimum load
---|---|---
Kommander-KA14 I| 2 Ω| 600 W @ 2Ω
Kommander-KA34| 4 Ω| 750 W @ 4Ω
Kommander-KA104| 4 Ω| 2500 W @ 4Ω
Kommander-KA18| 4 Ω| 150 W @ 4Ω
Kommander-KA28| 2 Ω| 600 W @ 2Ω
Kommander-KA68| 4 Ω| 750 W @ 4Ω
Kommander-KA208| 4 Ω| 2500 W @ 4Ω
Remote Connectivity
The Kommander-KA amplifier unit features a built-in hot spot establishing a
local Wi-Fi network dedicated to remote control the amplifier with mobile
devices. The default local Wi-Fi SSID and unit IP address are printed on a
label located on the rear plate of the unit; a QR code for easing the
connectivity is printed as well. The RJ45 Ethernet port on the rear panel
allows to connect the unit to a local area network (LAN). Since every host on
a network must be identified by a unique IP address, the simplest local
network usually implement a router/switch with a DHCP server managing the
addresses allocation: by default the Kommander-KA unit is set to obtain a
local IP address from the DHCP server. In case a DHCP server is not present on
the LAN, the unit goes in AutoIP mode: in few seconds the amplifier
automatically selfassign an IP address in the range 169.254.0.0/16. A static
IP address can be assigned to the amplifier unit using the amplifier’s
embedded web app (Network menu).
Connectivity Reset
With the unit switched on, keep pressed the RESET button on the rear panel for
10 to 15 seconds in order to:
- Revert the wired IP addressing to DHCP;
- Activate the built-in Wi-Fi and reset the wireless parameters to the default SSID name and password The status LED turns purple while the RESET button is pressed.
The Kommander-KA amplifiers can be controlled remotely by a mobile device or
desktop PC/MAC.
K-array Connect mobile app
K-array Connect is the mobile app that allows to direct manage and control a
Kommander-KA amplifier with a mobile device (smartphone or tablet) wireless.
Download the K-array Connect mobile APP from the dedicated store of your
mobile device.
http://software.k-array.com/connect/store
Embedded web app
The integrated operating system osKar features a complete web user interface
accessible over the network: connect to the Kommander-KA02 I on a local
network or wireless via its built-in hot spot and access the web app with a
web browser (Google Chrome recommended).
K-framework3
The K-array K-framework3 is the managing and control software dedicated to
professionals and operators looking for a powerful tool for designing and
managing a large number of units in demanding applications. Download the
K-framework3 software from K-array website.
https://www.k-array.com/en/software/
K-array Connect Mobile App
The K-array Connect mobile app allows to access the Kommander-KA amplifiers
wireless, leveraging on the local Wi-Fi established by the built-in hot
spot.
Connecting To The Built-In Hot Spot
- Ensure the Wi-Fi of the mobile device is on.
- Launch the K-array Connect app.
- If the list of available devices is empty touch the SCAN QR CODE button and use the mobile device camera to frame the QR code in the bottom panel of the Kommander-KA unit: this provides the mobile device to connect to the amplifier’s hot spot.
- Click on the image of the Kommander-KA unit to manage the amplifier with the K-array Connect app or click on the button with the globe in order to lanch the embedded web app.
**** In case you need to connect manually connect to the amplifier’s hot spot, the default password is the device serial number, e.g. K142AN0006 (case sensitive).
Scroll down to update the list of devices or
touch the Scan QR code button to activate
the camera in order to connect the unit| The K-array active unit has a label
with the QR
code for connecting the local Wi-Fi: target the
code to establish the wireless connection| Connected and discovered!
Embedded Web App
The embedded web app provides direct access to the operating parameters of the
amplifier unit.
The web app is accessible via a web browser (Google Chrome recommended) over a
wired or wireless connection to the amplifier unit.
The K-array Connect Mobile App and the K-framework3 software interfaces
include a shortcut for opening the web app, once the connection to the
amplifier unit is
established.
If the amplifier unit is connected to a LAN and its IP address is set and
known, it is possible to access its embedded web app typing its IP address in
the address bar of
the web browser.
Dashboard
The default menu provides access to the media player and the amplifier unit
setup parameters.
K-array
devices incorporate Dante as an optional software implemented solution, giving
the user to get immediate, nofuss connectivity over IP on demand.
The units born with no active Dante channels and can be upgraded to 2 IN x 2
OUT Dante channels (Ships with 0x0 / Upgradeable to 2×2).
Customers can make channel purchases directly within Dante Controller using
Audinate’s payment system.
When a unit receives Dante audio packets, it reconstructs them back into a
continuous digital audio stream, which is then played out over the DSP Media
channels.
The Dante audio implementation is 100% lossless 24- or 32-bit PCM, 48 kHz
sample rate.
Device preset
This tab contains the slot where to manage (save, import, export, delete) the
unit configuration.
Audio Configuration
Use this menu to access the input/output signal routing and output
configuration
Output Configuration
The Output Configuration is where the K-array loudspeaker factory presets can
be loaded on the output channels.
By default, all Kommander-KA units born with all the amplifier’s output
connections muted: in order to activate the output channels the output
configuration shall be set.
Care must be taken matching the loudspeaker presents with the actual
loudspeaker configuration.
-
Navigate the menu and go to Audio Configuration.
-
Go to the Output Configuration section.
-
Select the output channel to be configured.
-
Select the speaker factory preset corresponding to the loudspeaker model and version actually connected to the amplifier output connector.
-
If needed, set the number of loudspeakers that are connected in parallel to the amplifier output connector.
-
Select the matching loudspeaker, i.e. the subwoofer used in the actual loudspeaker configuration (eg. the Truffle-KTR26 matching the Vyper-KV25II) or the high/mid
loudspeaker when configuring a subwoofer output channel (eg. the Lyzard-KZ14I matching the Truffle-KTR25).
****
Ensure to set the proper loudspeaker factory preset corresponding to the
actual loudspeaker connected to the amplifier output channel -
Apply the output channel configuration.
-
If needed set the proper pairing channels in PBTL mode.
-
Go to the Routing section and set the proper signal routng.
MATRIX
The matrix allows to set the signal routing path between the amplifier’s input
channels and the amplifier’s output connectors. Blue boxes at the cross
intersection between raws and columns state an open path between sources (raw)
and destinations (columns).
INPATCH – 4-channel unit only
The input patch tab allows to address the input connections and the input
streamer (media player) to the four amplifier’s input channels.
The signal managed by the media player can be routed to the amplifiers’ input
channels via the Media-1 OUT and Media-2 OUT. Network
This menu section allows the user to monitor and set the network parameters.
WiFi
The WiFi can be configured to connect the unit to a wireless LAN as a CLIENT
or, alternatively, to create an independent local wireless network behaving as
HOT SPOT.
By default the WiFi is set as HOT SPOT allowing any mobile device to connect
to the unit.
By default, the SSID of the HOT SPOT is composed by the word “K-array-”
followed by the serial number of the unit; the default password is the unit’s
serial number. The SSID and the password of the HOT SPOT can be modified
manually: the QR Code will change accordingly.
When set as CLIENT, enter the data of the WiFi LAN in order to connect the
unit to that network.
The power switch allows to toggle on and off the WiFi.
Ethernet
Set the IP addressing static or DHCP.
Advanced
This menu provides access to the system informations, like the device name and
ID and the system update tool. System Update
In order to update the internal DSP software and osKar operating system two
methods are available: via an Internet connection or USB key.
Update via Internet
- Connect the Kommander-KA amplifier to Internet – possibly via a wired connection.
- The Download button turns active when a new software version is available on K-array server: when active, press on the Download button to start downloading the software from the Internet. This step doesn’t install the software: the installation shall be actiated manually.
- The Update button activates when the software is completely dowloaded: when active, press on the Update button to start updating the Kommander-KA amplifier.
The update procedure lasts in about 15 minutes: after updating the Kommander-
KA amplifier reboots.
Update via USB
A. Make a folder named update (case sensitive) on the root of a USB key or
drive.
B. Open the K-array website on the Internet browser on your PC or Mac.
C. Navigate the Products->Software menu and scroll down to the Download
section of the Software webpage.
D. Download the osKar System (ensure to be registered to the website in order
to proceed with the download) and save the update file with extension .mender
into the update folder on the USB drive.
E. Plug the USB drive to a free USB port on the amplifier rear panel. ****
F. If not already operating, switch on the Kommander-KA amplifier.
G. Connect your mobile device to the Kommander-KA amplifier and access the
embedded web app.
H. Naigate the user interface to the Advanced menu: the Install via USB button
activates when the USB drive contains the .mender file in the proper folder.
- Press on the Install via USB button to start updating the Kommander-KA unit.
The update procedure lasts in about 15 minutes: after updating the Kommander- KA amplifier reboots.
K-framework3
The Kommander-KA amplifiers can be remotely controlled with the dedicated
K-framework3 software available for PC and MAC on K-array website.
The K-framework3 is the managing and control software dedicated to
professionals and operators looking for a powerful tool for designing and
managing a large number of units in demanding applications.
https://www.k-array.com/en/software/
The K-framework3 operates in three modes:
- 3D – Design a loudspeaker system for your venue in a full 3D environment and make free field acoustic simulations;
- SETUP – import from the 3D design the active components into the workspace or build from scratch a PA system composed of active loudspeakers and amplifiers; use the input and output groups to allow full control of the system;
- TUNING – Manage and control the loudspeaker system in real time: optimize the performance of the loudspeaker system during the tuning session and control its
behavior in live events.
The K-framework3 can work either off-line with virtual devices or on-line with
real active loudspeakers and amplifiers connected over the same Ethernet
network.
The K-framework3 allows you to start designing the PA system off-line and sync
the virtual devices to the real ones on site, when the devices are available,
or import from scratch in the workspace the real active loudspeakers and
amplifiers available on the network. In both cases, in order to discover and
sync the active devices, both the PC or Mac running the K-framework3 and the
real units shall be properly connected to the same Local Area Network – LAN –
with star topology.
The network shall comprise:
- single PC or MAC, running the K-framework3 software with network interface 100Mbps (or higher);
- router with DHCP server 100Mbps (or higher);
- Ethernet switch 100Mbps (or higher);
- Cat5 (or higher) Ethernet cables.
A DHCP server is highly recommended even if the device units implement the zeroconf network technologies: if a DHCP service is not available, every device will self assign an IP address in the range 169.254.0.0/16 (auto-IP).
Discovery
- Ensure that all the units and the PC/Mac running the K-framework3 are properly connected to the same network.
- Power up the units.
- Launch the K-framework3.
- Open the Network window and launch the discovery: • If the K-framework3 finds two or more devices with the wrong ID, a dialog window appears where unique IDs can be assigned to the units.
- Once discovered, the real units are shown in the left columns, following the order of their ID number; if the workspace contains virtual devices of the same type you can eventually modify the IDs in order to match the units and allows the synchronization. The synchronization can be in either directions: Workspace-to-Real or Real- toWorkspace. Select the sync direction and synchronize all or the single units separately
Grouping
The working paradigm in the K-framework3 is to group the input and output
channels of the units in the workspace and adjust the system performance
within the groups.
Groups can be created working both off-line and on-line and are retained by
the real units even once unplugged: if a real device belongs to a group, the
group is re-created in the workspace during the synchronization process. An
active loudspeaker or amplifier might belong to multiple groups sharing its
features (eq filters, time delay, volume, etc).
**** The K-framework3 synchronization process reset to default the EQ, delay
and volume parameters edited with the K-array Control mobile app and the
embedded Web app.
A. In Setup mode: set the unit local parameters (presets, routing, input
gains, limiters, etc).
B. Add INPUT and OUTPUT groups as needed.
C. Assign the units’ channels to the groups.
D. Switch to Tuning mode.
E. Align the system using the tools available on the groups (eq, delay,
polarity,etc).
Service
To obtain service:
- Please have the serial number(s) of the unit(s) available for reference.
- Contact the official K-array distributor in your country: find the Distributors and Dealers list on K-array website. Please describe the problem clearly and completely to the Customer Service.
- You will be contacted back for on-line servicing.
- If the problem cannot be resolved over the phone, you may be required to send the unit in for service. In this instance, you will be provided with an RA (Return Authorization) number which should be included on all shipping documents and correspondence regarding the repair. Shipping charges are the responsibility of the purchaser. Any attempt to modify or replace components of the device will invalidate your warranty. Service must be performed by an authorized K-array service center.
Cleaning
Use only a soft, dry cloth to clean the housing. Do not use any solvents,
chemicals, or cleaning solutions containing alcohol, ammonia, or abrasives. Do
not use any sprays near the product or allow liquids to spill into any
openings.
Mechanical Drawing
DSP Block Diagram
4-channel units: KA14 I, KA34, KA104
Specifications
| Kommander-KA14 I| Kommander-KA34| Kommander-KA104
---|---|---|---
Type| 4ch switching mode. Class D Amplifier
Output Power’| 4x 600W @ 20| 4x 750W @ 40| 4x 2500W @ 40
Minimum impedance| 20| 40| 40
Frequency Response| 20 Hz – 20 kHz (±1 dB)
Connectors| Input:
4x XLR-F balanced input Remote connectivity:
lx Ethernet RJ45
Output: 4x USB-A
4x XLR-M balanced LINK output Wi-Fi IEEE 80211 b/g/n
2x PC 4/ 4-ST-7,62 speaker output
DSP| Input gain, routing matrix, delay, full parametric IIR filters (Peaking,
Shelving, Hi/Lo pass, Hi/Lo Butterworth).
On-board preset. Remote monitoring
Remote control| Wi-Fi dedicated APP I K-framework3 via wired Ethernet
connection
MAINS Operating Range| 100-240V AC. 50-60 Hz with PFC
Power Consumption| 400 W @ 8 0 load,
Pink noise, 1/4 rated power| 600 W @ 8 0 load,
Pink noise, 1/4 rated power| 600 W @ 4 0 load,
Pink noise. 1/4 rated power
Protections| Thermal protection. output short circuit, RMS output current
protection, high frequency protection. power limiter, clip limiter.
IP Rating| IP20
Dimensions (WxHxD)| 430 x 87 x 430 mm (17 x 3,4 x 17 in)
Weight| 6 kg (13,2 Ib)| 7 kg (15,4 Ib)| 8,15 kg (18 Ib)
| Kommander-KA18| Kommander-KA28| Kommander-KA68| Kommander-
KA208
---|---|---|---|---
Type| 8ch switching mode, Class D Amplifier
Output Power’| 8x 150W @ 40| 8x 600W @ 40| 8x 750W @ 40| 8x 2500W @ 40
Minimum impedance| 40| 20| 40| 40
Frequency Response| 20 Hz – 20 kHz (±1 dB)
Connectors| Input:
Remote connectivity:
8x XLR-F balanced input lx Ethernet RJ45
4x USB-A
Output:
4x PC 414-ST-7,62 speaker output Wi-Fi IEEE 80211 b/g/n
DSP| Input gain, routing matrix, delay, full parametric IIR filters (Peaking,
Shelving, Hi/Lo pass, Hi/Lo Butterworth).
On-board preset. Remote monitoring
Remote control| Wi-Fi dedicated APP I K-framework3 via wired Ethernet
connection
MAINS Operating Range| 100-240V AC, 50-60 Hz with PFC
Power Consumption| 300 W@ 8 Oload,
Pink noise, 1/4 rated power| 800 W @ 8 ()load.
Pink noise, 1/4 rated power| 1200 W @ 4 0 load.
Pink noise, 1/4 rated power| 1200 W @ 4 0 load.
Pink noise, 1/4 rated power
Protections| Thermal protection, output short circuit, RMS output current
protection, high frequency protection, power limiter, clip limiter.
IP Rating| IP20
Dimensions (WxHxD)| 430 x 87 x 430 mm (17 x 3,4 x 17 in)
Weight| 7 kg (15,4 lb)| 7,4 kg (16,3 lb)| 8,3 kg (18,3 Ib)| 10 kg (22 Ib)
Designed and Made in Italy
K-ARRAY surl
Via P. Romagnoli 17 | 50038 Scarperia e San Piero – Firenze – Italy
ph +39 055 84 87 222 | info@k-array.com
www.k-array.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>