X-POWER 10810005 Cable Hoist/Puller Owner’s Manual
- June 10, 2024
- X-POWER
Table of Contents
X-POWER 10810005 Cable Hoist/Puller
Product Information
The Cable Hoist/Puller Model Number 10810005 is a heavy-duty product designed for lifting and pulling. It has a lift capacity of 750 lbs and a pull capacity of 1500 lbs. The product features a 15 ft single line and a foldable handle that fits into a compact package. The Cable Hoist/Puller has a dual ratchet design for enhanced performance.
Operating Instructions
TO APPLY TENSION, engage the drive lever by pushing the shift lever (located above the drive lever) rearward until the spring is seated in the alt detent. Pivot handle assm back & forth to rotate ratchet wheel and take-up line tension.
TO RELEASE TENSION, disengage the drive lever by pushing the shift lever forward until the spring is seated in the front detent. Pivot the handle forward until the drive & stop levers are in contact. Continue to apply pressure against the stop lever until it releases and then allow the handle to pivot back. Repeat this procedure to safely release the load a notch- at-a-time.
TO FREEWHEEL SPOOL, release all of the line tension, manually disengaged the stop lever by pulling back on the exposed wire loop and unreel the desired length of cable.
Use Considerations
CAUTIONS: This product is not recommended for use as a load binder or
tie-down. The handle is designed to bend if overloaded; do not use an
extension bar on the handle. Never stand in front of, or in line with a
pretensioned mechanism. Do not use to lift people or loads overhead. Do not
operate hoist/puller with twisted, frayed, damaged, or kinked cable/webbing.
Do not pull cable/webbing over sharp corners or secure hook back onto the
cable.
Warranty
Limited 90 Day Warranty to Original Using Buyer
CABLE HOIST/PULLER
Model Number: 10810005
- 750 LB. Lift Capacity
- 1,500 LB. Pull Capacity
- 15 ft Single Line
- Foldable handle fits into compact packag
- Heavy Duty, Dual Ratchet Design
OPERATING INSTRUCTIONS GUIDE
TO APPLY TENSION, engage the drive lever by pushing the shift lever (located above the drive lever) rearward until the spring is seated in the alt detent. Pivot handle assm back & forth to rotate ratchet wheel and take-up line tension.
TO RELEASE TENSION, disengage the drive lever by pushing the shift lever forward until the spring is seated in the front detent. Pivot the handle forward until the drive & stop levers are in contact. Continue to apply pressure against the stop lever until it releases and then allow the handle to pivot back. Repeat this procedure to safely release the load a notch- at-a-time.
TO FREEWHEEL SPOOL, release all of the line tension, manually disengaged the stop lever by pulling back on the exposed wire loop and unreel the desired length of cable.
For replacement parts and technical questions, please contact Customer Service at 1-888-380-7428
USE CONSIDERATIONS WITH AIRCRAFT CABLE HOIST/PULLERS
- Do not pull cable over sharp corner
- Do not link hook back onto cable
- Do not lift people or loads over people
CAUTIONS
- Read and understand all instructions before using.
- Inspect mechanism and cable/ webbing for proper operation and condition before each use.
- Know your loadings; do not exceed rated capabilities.
- This product is intended for straight-in-line lifting and pulling do not side load mechanism or cable/webbing.
- Do not shock load mechanism or cable / webbing.
- Always keep a minimum of two wraps of cable or one wrap of webbing on the hub while mechanism is under load.
- Always use puller under manual Power; do not use in place of tow line.
- This product is not recommended for use a load binder or tie-down.
- Handle is designed to bend if overloaded; do not use an extension bar on the handle.
- Never stand in from of, or in line with a pretensioned mechanism.
- Do not use to lift people or loads overhead.
- Do not operate hoist/puller with twisted, frayed, damaged or kinked cable/webbing.
- Do not pull cable/webbing over sharp corners or secure hook back onto cable.
WARRANTY INFORMATION
“Limited 90 Day Warranty to Original Using Buyer”
All X-POWER Hoist Pullers are warranted for 90 days against defects when
operated under normal conditions, within their rated capacities and in
accordance with the operating instructions and use considerations.
This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of
maintenance. We shall in no event be liable for death, injuries to persons or
property, or for incidental, contingent, special, or consequential damages
arising from the use of our product. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation of
exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>