Thermaltake ARGENT P900 Smart Gaming Desk User Manual

Thermaltake ARGENT P900 Smart Gaming Desk

WARNING:
FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.

IMPORTANT INFORMATION

Please read this manual carefully.

• Please read this manual carefully.
• This document contains all relevant safety regulations. Any non-conforming use may result in personal injury or mechanical damage.
• Please read this operation manual carefully before use. The manual provides a lot of important information about the safety, use, assembly and subsequent maintenance of the lifting table; it can avoid many unnecessary injuries.
• If this desk is sold, please provide this manual to the buyer.
• Do not sit or stand on the desk. Do not crawl or lie under the desk.
• Failure to comply with or ignore any safety requirements, assembly instructions, user operations and related warnings may result in serious personal injury or mechanical damage. Please operate and Before assembly, really understand the relevant regulations. This product is not a toy. Please be careful.
• Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
• If the supply cord is damaged, it must be replaced by the manufacturer and its service agent in order to avoid a hazard.
• This product is not intended for use by young children without supervision.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• This product can be used by children from 8 years old (supervised) to Adult. Users with disabilities or lack of experience and operating knowledge should be supervised and given careful instructions prior to using this product. The desktop should never be sat on and children should be prohibited from having unsupervised contact with the product.
• Cleaning and user maintenance shall not be made by children without supervision.

Do not over tighten screws during installation.

CAUTION:

• Please place the product away from corrosive gas, water and dusty environments.
• Alteration or madding of any factory components outlined in the checklist will automatically void your warranty.

USE & LIABILITY

• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• The height adjustable desk is designed for indoor use and dry work areas only. The desk height is adjustable so that it can be positioned at the most suitable height. Any other use is at the user’s risk. Under no circumstances does the manufacturer accept warranty claims or liability claims for damages caused from improper use or handling of the desk.

Specifications

ARGENT P900 SMART GAMING DESK

DESK DIMENSIONS

PARTS LIST

SCREWS

TOOLS

It is recommended to use hand tools & electric hand tools/ no inclusion

STEP: 1

STEP: 2

STEP: 3
Do not fully tighten screws until completely assembled

STEP: 4

STEP: 5

STEP: 6
Do not fully tighten screws until completely assembled

STEP: 11

STEP: 12

STEP: 13
Assembly Motor Control Parts

STEP: 14
Connecting the Light Bar Control Box

STEP: 15

Panel Controller Instructions

Control panel

• Press and hold • to raise height level.
• Press and hold T to lower height level.
• Adjust the height to the storage height, and 4 heights can be set.
• Display will turn off after 10 seconds of. Press any button to activate display.

Reset

• Press both • and T buttons at the same time for 3 seconds to reset desk to default position. The control box will ‘beep’ to confirm successful reset. Pressed buttons can now be released.

• When conducting reset, display will show “EOO” during last 100mm. When finished resetting, display will indicate default starting height.

• If• and T buttons are released before reset is completed, the desk will not function. The display will
  indicate “EOO” if any button is pressed. User must complete reset procedure to revert to normal operation.

• Reset is necessary for first operation of the desk.

Starting Height Display change

• Default starting height is 70cm.
• To adjust the starting height, press T button to go to the lowest position of the desk. At the lowest position, press T button again for at least 5 seconds, display starts flashing for 10 seconds.
• During the 10 seconds, press • or T buttons to adjust the starting height number. After 10 seconds, the display stops flashing and the preferred starting height is shown and has been stored.

Storing Memory Profiles

• Supports 4 memory positions.
• Operate the desk to preferred height.
• Press any of CD@®© together with • or T for 2 seconds to store the current height. Display shows P1 /P2/P3/P4 when the position has been stored.
• When there is already a position stored, hold the button CD@®© until the desk reaches the stored height.
• Stored position can only be overwritten but not to be cleared.

Customizing Desk Height – setting new upper & lower limits for your desk Setting Upper Limit 

• Operate the system and stop at the preferred upper limit height.
• Press together, and release Twithin 3 seconds (before it goes to reset mode)
• Keep holding and press T button 5 times continuously.
• One ‘beep’ sound will indicated successful completion of setting.

TROUBLESHOOTING

• If your desk is not functioning properly it may need to be reset. Unplug the power cord for 20 seconds. Plug the power cord back in and follow the RESET procedure.
• Reset may be needed from time to time in events like non-movement, uneven movement, sudden power outage, over-load, overheat and etc.

ERROR CODE FOR DESK WITH MEMORY CONTROLLER

WI-Fl control box setting

• Please download and install the “TT RGB DESK” APP.
  Android version: TT RGB DESK.
  iOS version: TT RGB DESK.

• Please confirm that the WI-Fl function of the mobile device is turned on, and enter the WI-Fl

• Open the APP, click on the WI-Fl list, select the WI-Fl name, enter the password and connect to use the APP. For the latest User Installation Guide , please visit: www.thermaltake.com

Industry Canada statement: This device complies with ISED’s licence- exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FOR MOBILE DEVICE USAGE { >20cm/low power)
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>