Fodenn MINIF10 Mini PC User Manual
- June 1, 2024
- Fodenn
Table of Contents
Fodenn MINIF10 Mini PC
Specifications
- Model: 6TFS.BOVBM
- Power Input: 0/5&/54
- Operating Voltage: #BTJD0QFSBUJPO
- Dimensions: VUUPOQPSUT
Product Usage Instructions
Thank you for choosing Fodenn. Please read the user manual carefully ,and keep it for future reference.
Powering On the Device
To power the device, press the ‘ON’ button located on the front panel. The power indicator light should illuminate.
Adjusting Settings
Use the control knob to adjust various settings such as volume, brightness, and mode selection. Rotate the knob clockwise or counterclockwise to make adjustments.
Connecting External Devices
To connect external devices, use the provided cables and ports located at the back of the device. Ensure a secure connection to avoid signal loss.
Packing List
- Mini PC*1
- Power Adapter*1
- HDMI Cable*1
- User Manual*1
- Hard disk fixing screws*4
- Mini PC copper fixing screws*2
- VESA Mounting Bracket*1
- VESA Mounting Bracket Screws*2
Basic Operation
Button & ports
- MIC headphone jack
- USB port
- Power button
- LAN port
- HDMI port
- DC in port
- Security keyhole
Failure to use the included power adapter may violate regulatory compliance
requirements and may expose the user to safety hazards.
Specifications are subject to the physical product.
The Following Operations Should be Started With the Power Off
DDR Memory Installation. (As shown in the picture)
- Align the memory module key along with the memory socket key and insert the memory at a 30-degree angle, Slide the module into place.
SSD Card Installation. (As shown in the picture)
- Align the notches on the SSD with the tabs in the M.2 slot on the motherboard.
- Slide SSD in then secure the SSD with a screw.
Note: The HDD installation guide is inscribed on the HDD cover.
Connection Steps
- Connect to the monitor with an HDMI cable
- Connect the keyboard and mouse
- Connect the power supply
Tips and FAQ
How to boot into the system for the first time?
When you start up your PC for the first time, you will be guided to configure
your Windows operating system.
Start up your Mini PC for the first time: Press the PC’s power button. Wait
for a few minutes until the installation interface appears.
-
Step 1: Select language/country(region)
-
Step 2: Select the inputting method, and click confirm
-
Step 3: Select the second inputting method, which can be” skipped”
-
Step 4: Networking: After selecting Wi-Fi enter the password to connect it. Or choose to plug a network cable for connection.
Networking will be updated automatically, and the update process will stay on an interface for a long time, which prolongs the start-up time.
(Skipping network connections is strongly recommended) -
Step 5: Accept License Agreement
-
Step 6: Set User Name and Password Once the installation process is complete, the desktop will appear.
How to connect a WiFi network?
- Find and click the Wi-Fi icon to turn on the Wi-Fi.
- Select an access point in the list of available Wi-Fi connections.
- Select one of the connections to start the network connection.
Note: You may be prompted to enter a security key to activate a Wi-Fi connection.
How to enter the BIOS setting page?
- The BIOS(Basic Input/ Output System is the first software loaded when the Mini PC starts.
- Enter Bios: Click the “Del” or”ESC” key.
- Under normal circumstances, the default BIOS settings apply in most cases to ensure optimum performance. Do not change the default BIOS settings except for the following situation. (You have installed new system components that require further BIOS settings or updates.)
- Warning! Inappropriate BIOS settings may cause instability or startup failure.
We strongly recommend that you only change the BIOS settings with the help of technical service personnel.
How to force the shutdown of your Mini PC?
If your Mini PC does not respond, press the power button for at least (4-6) seconds until your Mini PC is turned off.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. NOTE: This equipment
has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However. there is no
guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NOTE: This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, this equipment
should be installed and operated with a minimum distance of 20cm from the
radiator of your body. This device and its antenna(s) must not be co-located
or operated in conjunction with any other antenna nr transmitter.
IC warning
This device contains licence-exempt transmitters)/receivers)/ that comply with
Innovation Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- this device may not cause interference and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada’s radiation
exposure limits set forth for an uncontrolled environment; To maintain
compliance with IC’s RF Exposure guidelines.
This equipment should be. installed and operated with a minimum distance of
20cm the radiator your body. This device and its antenna(s) must not be co-
located or operated in conjunction with any athar antenna ortranemittor
Frequently Asked Questions (FAQ)
Q: How do I reset the device to factory settings?
A: To reset the device to factory settings, locate the reset button at the back of the device. Use a small tool to press and hold the button for 10 seconds until the device restarts.
Q: Can I use this product internationally?
A: Yes, this product is designed to support international voltage standards. However, you may need a plug adapter to fit different types of power outlets.
Q: What should I do if the device malfunctions?
A: If the device malfunctions, first try restarting it by unplugging it from the power source for a few minutes and then plugging it back in. If the issue persists, consult the user manual for troubleshooting tips or contact customer support for assistance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>