Apex 70256 Digital Thermometer Owner’s Manual

Apex 70256 Digital Thermometer

WARNING

• Read instructions thoroughly before using a digital thermometer.
• Choking Hazard: Thermometer cap and battery may be fatal if swallowed. DO NOT allow children to use this device without parental supervision.
• DO NOT use a thermometer in the ear. Designed use is for oral, rectal, or armpit (axilla) readings only.
• DO NOT place the thermometer battery near extreme heat as it may explode.
• Note: Use of the probe cover may result in a 0.2°F (0.1°C) discrepancy from actual temperature.
• Remove the battery from the device when not in operation for a long time.
• The use of temperature readings for self-diagnosis is dangerous. Consult your doctor for the interpretation of results. Self-diagnosis may lead to the worsening of existing disease conditions.
• DO NOT attempt measurements when the thermometer is wet as inaccurate readings may result.
• DO NOT bite the thermometer. Doing so may lead to breakage and/or injury.
• DO NOT attempt to disassemble or repair the thermometer. Doing so may result in inaccurate readings.
• After each use, disinfect the thermometer especially in case the device is used by more than one person.
• DO NOT force the thermometer into the rectum. Stop insertion and abort the measurement when pain is present. Failure to do so may lead to injury.
• DO NOT use the thermometer orally after being used rectally.
• For children who are two years old or younger, please do not use the devices orally.
• if the unit has been stored at temperatures over 41°F – 104°F (5°C – 40°C), leave it in 41°F – 104°F (5°C – 40°C) ambient temperature for about 15 minutes before using it.

PLEASE READ CAREFULLY BEFORE USING

This digital thermometer provides a quick and highly accurate reading of an individual’s body temperature. The digital thermometer is intended to measure the human body’s temperature in regular mode orally, rectally or under the arm, and the device is reusable for clinical or home use on people of all ages. To better understand its functions and to provide years of dependable results, please read all instructions first.

THIS APPLIANCE CONFORMS TO THE FOLLOWING STANDARDS: ASTM El 112 Standard Specification for Electronic Thermometer for Intermittent Determination of Patient Temperature, ISO 80601-2-56 Medical electrical equipment-Part 2-56:Particular requirements for basic safety and essential performance of clinical thermometers for body temperature measurement, IEC 60601-1-11 Medical electrical equipment-Part 1-11: General requirements for basic safety and essential performance-Collateral Standard: Requirements for medical electrical equipment and medical electrical systems used in the home healthcare environment and complies with the requirements of IEC 60601-1-2(EMC), AAMI/ANSI ES60601-1(Safety) standards. And the manufacturer is ISO 13485 certified.

PRECAUTION

The performance of the device may be degraded should one or more of the following occur:

• Operation outside the manufacturer’s slated temperature and humidity range.
• Storage outside the manufacturer’s slated temperature and humidity range.
• Mechanical shock (for example, being dropped).
• Patient temperature is below ambient temperature.
• Portable and mobile RF communications can affect the device. The device needs special precautions regarding EMC.
• Keep the thermometer away from Magnetic Resonance equipment.

SYMBOL EXPLANATION

| Direct Current| | Manufacturer
---|---|---|---
|

Type BF Applied Part

| | Storage and Transportation Temperature Limit:

-4°F~131°F (-20°C~55°C)

| Batch Code| |

Figure 1

SPECIFICATIONS

• Type: Digital Thermometer (Not Predictive)
• Measure Range: 90.0°F -109.9°F (32.0°C -42.9°C) (C°/°F chosen by manufacturer)
• Accuracy: ±0.2°F(±0.1°C) during 95.9°F ~ 107.6°F (35.5°C ~ 42.0°C) at 64.4°F ~ 82.4°F (18°C ~ 28°C ) ambient operating range ±0.4°F(±0.2°C) for other measuring and ambient operating range
• Measure time: < 45 seconds
• Expected service life: Three years
• Operating mode: Direct Mode
• Display: Liquid crystal display, 3 1/2 digits
• Memory: For storing the last measured value
• Battery: One 1.5 V DC. button battery (size LR41 or SR41, UCC 392)
• Battery life: Approx. 200 hours
• Dimension: 13.5cm x 3.4cm x 1.7cm (L x W x H)
• Weight: Approx. 22 grams including the battery
• Ambient operating range: Temperature: 41°F ~ I04°F(5°C~40°C)
• Relative humidity: 15% ~ 95%RH
• Atmospheric Pressure: 800hPa ~ 1060hPa
• Storage and transportation condition: Temperature: -4°F ~ 131°F(-20°C ~ 55°C)
• Relative humidity: 15% ~ 95%RH
• Atmospheric Pressure: 800hPa ~ 1060hPa
• Ingress Protection Rating: 1P27
• Classification: Type BF

DIFFERENT TEMPERATURE DIFFERENT COLOR:

At the completion of each measurement, the triangular arrow on the display will indicate different colors according to different temperature ranges.

°C/°F SWITCHABLE

• Temperature readings are available in the Fahrenheit or Celsius scale (°C/°F; located in the upper right corner of LCD.) With the unit off, press and hold the On/Off Button for approximately 4 seconds to change the current setting.

DIRECTIONS

1. Press the On/Off Button next to LCD display to turn on the unit. The display will briefly show 188.8°E with a backlit and beep tone. Followed by the last temperature or Lo°F or Lo°C (if no reading is stored in memory), the thermometer is now in the testing mode.
   Note: if the measured temperature is less than 90°F or 32°C, the LCD will display Lo, if the measured temperature is higher than 109.9°F or 42.9°C, the LCD will display Hi.

2. Position the thermometer in the desired location (mouth, rectum, or armpit.)

   • Oral Use: Place the thermometer under the tongue as indicated by “✓” position shown in Figure 2. Close your mouth and breathe evenly through the nose to prevent the measurement from being influenced by inhaled/exhaled air. Normal temperature between 96.3°F and 99.1°F (35.7°C and 37.3°C)
   • Rectal Use: Lubricate the silver probe tip with petroleum jelly for easy insertion. Gently insert the sensor approximately l cm (less than 1/2 “) into the rectum. Normal temperature between 97.2°F and 99.9°F (36.2°C and 37.7°C).
   • Armpit Use: Wipe the armpit dry. Place the probe in the armpit and keep the arm pressed firmly at the side. From a medical viewpoint, this method will always provide inaccurate readings, and should not be used if precise measurements are required. Normal temperature between 95.4°F and 98.1°F (35.2°C and 36.7°C).

3. The degree sign flashes throughout the testing process. When flashing stops an alarm will beep for approximately 10 seconds. The measured reading will appear on the LCD simultaneously. The minimum measurement time until the signaling tone (beep) must be maintained without exception. The measurement continues even after the alarm notification. The displayed temperature will not change when the thermometer is removed from its testing position. *Note: Normally the alarms are “Bi-Bi-Bi-Bi-“; Alarm beeps more rapidly when temperature reaches 100°F (37.8°C) or higher, and the alarms are “Bi-Bi-Bi—–Bi-Bi-Bi——- Bi-Bi-Bi”.

4. To prolong battery life, press the On/Off Button to turn the unit off after testing is complete. lf no action is taken, the unit will automatically shut off after around 10 minutes.

5. Clean and disinfect the thermometer and then store the thermometer in its protective case.

BATTERY REPLACEMENT

1. Replace the battery when “ ” appears in the lower right corner of LCD display.
2. Put a thin board such as a coin on the fillister of the cover. Turn the battery anti-clockwise until the cover is off. (See Figure 3)
3. Use a non-metal instrument such as a pen to remove the old battery from the battery holder (See Figure 4). Discard battery according to local law.
4. Place a new 1.5V DC button type LR41 or SR41, UCC392, or equivalent into the chamber with the positive side facing up. (See Figure 5).
5. With a thin pin turn the cover clockwise until the ” ” facing towards ” ” .(See Figure 6)

CLEANING AND DISINFECTION

1. Immerse the thermometer in distilled water for at least 1 minute;
2. Use a clean, soft cloth to wipe the thermometer down to remove any residue;
3. Repeat steps 1 and 2 three times;
4. For disinfection, immerse the thermometer in 0.55% OPA, such as CIDEX OPA, for at least 12 minutes under a temperature at 20°C;
5. Repeat steps 1 to 3; Note: Please operate according to the manual of OPA for reference. To prevent damage to the thermometer Please note and observe the following:
6. Do not use benzene, paint thinner, gasoline or other strong solvents to clean the thermometer.
7. Do not use ultrasonic washing to clean the thermometer.

FCC INFORMATION

Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CALIBRATION

• The thermometer is initially calibrated at the time of manufacture.
• lf the thermometer is used according to the use instruction, periodic readjustment is not required.  However, we recommend checking calibration every two years or whenever clinical accuracy of the thermometer is in question.
• Turn on the thermometer and insert into the water bath which the temperature is steady.
• ASTM laboratory accuracy requirements in the display range of 98.6 to 102.2°F (37.0 to 39.0°C) for electronic thermometers is ±0.2°F(±0.1°C).
• The above recommendations do not supersede the legal requirements.
• The user must always comply with legal requirements for the control of the measurement, functionality, and accuracy of the device which are required by the scope of relevant laws, directives or ordinances where the device is used.

LIMITED WARRANTY

• The thermometer is guaranteed for one year from the date of purchase.
• lf the thermometer does not function properly due to defective components or poor workmanship, we will repair or replace it free of charge.
• All components are covered by this warranty excluding the battery.
• The warranty does not cover damages to your thermometer due to improper handling.
• To obtain warranty service, an original or copy of the sales receipt from the original retailer is required.

ELECTROMAGNETIC COMPATIBILITY INFORMATION

The device satisfies the EMC requirements of the international standard IEC 60601-1-2. The requirements are satisfied under the conditions described in the table below. The device is an electrical medical product and is subject to special precautionary measures with regard to EMC which must be published in the instructions for use. Portable and mobile HF communications equipment can affect the device. Use of the unit in conjunction with non-approved accessories can affect the device negatively and alter the electromagnetic compatibility. The device should not be used directly adjacent to or between other electrical equipment.

Table 1

Guidance and declaration of manufacturer-electromagnetic emissions

The device is intended for use in the electromagnetic environment specified below.

The customer or the user of the device should assure that it is used in such an environment.

Emissions test| Compliance| Electromagnetic environment-guidance

RF emissions CISPR 11

|

Group 1

| The device uses RF energy only for its internal function. Therefore, its emissions are very low and are not likely to cause any interference in nearby electronic equipment.

RF emissions CISPR 11

|

Class B

| The device is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Harmonic emissions IEC 61000-3-2| N/A|
Voltage fluctuations/flicker emissions IEC 61000-3-3|

N/A

|

Table 2

Guidance and declaration of manufacturer-electromagnetic immunity

The device is intended for use in the electromagnetic environment specified below.

The customer or the user of the device should assure that it is used in such an environment.

IMMUNITY test| IEC 60601 test level| Compliance| Electromagnetic environment guidance
Electrostatic discharge (ESD) IEC 61000-4-2| ± 6 kV contact

± 8 kV air

| ± 6 kV

contact

± 8 kV air

| Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30 %.
Electrostatic transient/burst IEC 61000-4-4| ± 2 kV for power supply lines

± 1 kV for input/ output lines

| N/A|
Surge

IEC 61000-4-5

| ± 1 kV differential mode

± 2 kV common mode

| N/A|
Voltage dips, short interruptions and voltage variations on power supply input lines

IEC 61000-4-11

| < 5% UT (>95% dip in UT)

for 0.5 cycle

40% UT (60% dip in UT)

for 5 cycle

70% UT (30% dip in UT)

for 25 cycle

<5% UT (>95% dip in UT)

for 5 secretary

| N/A|
Power frequency (50/60 Hz)

magnetic field IEC 61000-4-8

| 3 A/m| 3 A/m| Power frequency magnetic fields should be at levels charactertic of a typical location in a typical comme-rcial or hospital environment.

Table 3

Guidance and declaration of manufacturer-electromagnetic immunity

The device is intended for use in the electromagnetic environment specified below.

The customer or the user of the device should assure that it is used in such an environment.

IMMUNITY test| IEC 60601 test level| Compliance level| Electromagnetic environment guidance
Conducted RF IEC 61000-4-6

Radiated RF IEC 61000-4-3

| 3 Vrms 150 kHz to 80 Mhz

3 V/m 80 MHz to 2.5 Ghz

| N/A

3 V/m

| Portable and mobile RF communications equipment should be used no closer to any part of the device, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.
| | | Recommended seperation distance 80 MHz to 800 MHz

800 MHz to 2.5 Ghz

| | | where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the

recommended separation distance in metres (m).

| | | Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less than the compliance level in each frequency range.
| | | Interference may occur in the vicinity of equipment marked with the following symbol:

Recommended separation distances between portable and mobile RF communications equipment and the device

The device is intended for use in an electromagnetic environment in which radiated therefore disturbances are controlled. The customer or the user of the device can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the device as recommended below, according to the maximum output power of the communications equipment.

Rated maximum output power of transmitter

W

| Separation distance according to frequency of transmitter m
---|---
80 MHz to 800 MHz

| 800 MHz to 2.5 GHz

0.01| 0.12| 0.23
0.1| 0.38| 0.73
1| 1.2| 2.3
10| 3.8| 7.3
100| 12| 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

NOTE1 At 80 MHz and 800 MHz, the separation distance for the higer frequency range applies.

NOTE2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.

Disposal of this product and used batteries should be carried out in accordance with the national regulations for the disposal of electronic products.

Manufactured for / Fabricado por: Compass Health Brands Corp. Middleburg Heights, OH 44130 www.compasshealthbrands.com

Phone / Teléfono 800.376.7263 Made in China / Hecho en China 42-70256_02 © 2018

FREQUENTLY ASKED QUESTIONS

What is the brand and model of the digital thermometer?

The brand is Apex, and the model is 70256 Digital Thermometer.

What special feature does the Apex 70256 Digital Thermometer offer?

The Apex 70256 Digital Thermometer boasts a Fast Reading System, providing quick and accurate temperature measurements.

What type of outer material is used in the construction of the Apex 70256 Digital Thermometer?

The outer material of the Apex 70256 Digital Thermometer is plastic, ensuring durability and lightweight design.

What type of display does the Apex 70256 Digital Thermometer have?

The Apex 70256 Digital Thermometer features a digital display, making temperature readings easy to read and understand.

What are the product dimensions of the Apex 70256 Digital Thermometer?

The product dimensions of the Apex 70256 Digital Thermometer are 5.3 x 1.3 x 0.7 inches, providing a compact and portable design.

What is the weight of the Apex 70256 Digital Thermometer?

The Apex 70256 Digital Thermometer weighs 0.3 ounces, ensuring it is lightweight and easy to carry around.

What type of battery does the Apex 70256 Digital Thermometer require?

The Apex 70256 Digital Thermometer requires 1 CR2 battery for operation.

Who is the manufacturer of the Apex 70256 Digital Thermometer?

AmazonUs/APEY9 is the manufacturer of the Apex 70256 Digital Thermometer, ensuring quality and reliability.

What is the price of the Apex 70256 Digital Thermometer?

The price of the Apex 70256 Digital Thermometer is $8.01, offering affordability without compromising functionality.

What is the warranty period for the Apex 70256 Digital Thermometer?

The Apex 70256 Digital Thermometer comes with a one-year warranty, providing assurance of quality and customer satisfaction.

What should I do if the Apex 70256 Digital Thermometer is not displaying any readings?

Firstly, ensure that the battery is correctly inserted and has sufficient charge. If the issue persists, try replacing the battery with a new one.

What steps should I take if the Apex 70256 Digital Thermometer display is malfunctioning?

Check for any visible damage to the display or connections. Try resetting the thermometer by removing and reinserting the battery.

What should I do if the Apex 70256 Digital Thermometer is not responding to button presses?

Ensure that the buttons are not stuck or obstructed. Try cleaning around the buttons with a soft cloth.

How can I troubleshoot connectivity issues with the Apex 70256 Digital Thermometer?

The Apex 70256 Digital Thermometer typically does not have connectivity features. However, if you're experiencing issues with temperature readings, ensure the thermometer is properly calibrated and positioned.

How can I troubleshoot a malfunctioning auto power-off feature on the Apex 70256 Digital Thermometer?

Check the settings to ensure the auto power-off feature is enabled. If it's enabled and still not functioning properly, try resetting the thermometer.

DOWNLOAD THE PDF LINK:Apex 70256 Digital Thermometer Owner’s Manual

REFERENCE:Apex 70256 Digital Thermometer Owner’s Manual- Device.Report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>