Miele 11605080-04 Professional Vented Dryer Instruction Manual

11605080-04 Professional Vented Dryer
Instruction Manual

PDR 914/514 EL

Installation notes

Installation requirements
Risk of injury or damage to property due to improper installation.
Incorrect installation of the tumble dryer can lead to personal injury or damage to property.
The tumble dryer must only be installed and commissioned by Miele Customer Service Department or an authorised dealer.

• The tumble dryer must be installed in accordance with all relevant regulations and standards.
• The dryer must only be operated in a room that has sufficient ventilation and which is frost-free.
• The tumble dryer must not be installed behind a closeable door or a sliding door. The maximum opening angle of the tumble dryer door must not be limited by objects or doors. It must be possible to fully open the tumble dryer door at any time.

Electrical connection
The electrical connection must be established by a qualified electrician.

• The electrical connection may only be made to an electrical system provided in accordance with all appropriate local and national legislation, regulations and guidelines. Please also observe the regulations set out by your insurance  provider and energy supplier, accident prevention regulations, as well as recognised codes of practice.

• Reliable and safe operation of this tumble dryer is only ensured if it has been connected to the mains electricity supply.
  The required supply voltage, power rating and fuse rating can be found on the data plate on the tumble dryer. Ensure that the supply voltage matches the voltage quoted on the data plate before establishing the electrical connection to the  tumble dryer.
  Connection to a supply voltage other than the one quoted on the data plate can damage the tumble dryer if the voltage is too high.

• If more than one voltage is specified on the data plate, the tumble dryer can be converted for connection to the relevant input voltage. This conversion must be performed by the Miele Customer Service Department or by an  authorised dealer. During the conversion, the wiring instructions given on the wiring diagram must be followed.
  Tip: We recommend connecting the tumble dryer to the power supply via a plug and socket so that it is easier to  conduct electrical safety checks (e.g. during maintenance or repair work).

It is advisable to connect the product via a suitably rated plug and socket in accordance with IEC-60309, otherwise for a hardwired connection an all pole means of isolation must be installed at the site.
An isolation device is a switch which ensures a contact opening of more than 3 mm. These include circuit breakers, fuses and contactors (IEC/EN 60947).
If the mains supply cannot be permanently disconnected, the isolation device (including plug and socket) must be safeguarded against being switched on either unintentionally or without authorisation.

• The tumble dryer must not be connected to devices such as timers which would switch it off automatically.
  If local regulations require that a residual current device (RCD) is installed, a type B residual current device (sensitive to universal current) must be used.

• After installing the tumble dryer, equipotential bonding must be established. The equipotential bonding must comply with the local and national installation specifications.

Air intake/exhaust air
The tumble dryer may only be operated when the ducting has been connected properly and the room is sufficiently ventilated.
Accessory parts may only be fitted when expressly approved by Miele. If other parts are used, warranty, performance and product liability claims will be invalidated.

PDR 914/514, electrically heated

Dimensions

Installation

Dimensions quoted in millimetres

Installation (standard/UG)

UG Box plinth
B Drill hole/anchor point
Installation (on concrete plinth/offshore)

BS Concrete plinth
B Drill hole/anchor point

Technical data

Possible voltage variants
Voltage variant 1

| Standard connection
---|---
Supply voltage| 3N AC 400 V
Frequency| 50/60 Hz
Power rating| 14.1 kW
Fuse rating (on site)| 3×25 A
Minimum cross-section for connection cable| 5×4.0 mm²
Cable gland| M32

Voltage variant 2

| Standard connection
---|---
Supply voltage| 3 AC 230 V
Frequency| 50/60 Hz
Power rating| 14.1 kW
Fuse rating (on site)| 3×35 A
Minimum cross-section for connection cable| 4×6 mm²
Cable gland| M32

Exhaust air

As relative humidity inside the exhaust ducting can be as high as 100 %, suitable measures must be taken to prevent a backflow of
condensate into the machine.

Air intake

Standard connection: air intake from installation site

Recommended free air intake cross-section into the room:
(equivalent to 3 times the exhaust air cross-section of a machine).
There must be sufficient air intake to the installation site to match the air outlet volume.| 763 cm²
---|---

Alternative connection: air intake connection directly from outdoors

Removing the protective cover exposes live parts. For safety reasons, a pipe must be installed from the tumble dryer’s central fresh air intake (over a minimum length of 900 mm) and secured with 2 screws.
Equipotential bonding (optional)

Accessories for equipotential bonding are not supplied and need to be ordered separately.
Peak-load negotiation (optional)

Miele recommends using a flexible connection cable with an additional isolation option to establish the connection. The isolator should remain visible once the tumble dryer has been installed and must be freely accessible.
Machine data

Fixing options
Fixing without plinth

| Quantity| Screw size
---|---|---
Tensioning strips| 2|
Wood screws DIN 571 (Ø × length)| 2| 6×40 mm
Plugs (Ø × length)| 2| 10×50 mm

If the tumble dryer is being installed without a plinth, fixing it in place is recommended.
Fastenings for floating screed must be supplied by the customer on site.

Fixing to concrete plinth

| Quantity| Screw size
---|---|---
Tensioning strips| 2|
Wood screws DIN 571 (Ø × length)| 2| 6×40 mm
Plugs (Ø × length)| 2| 10×50 mm

If the tumble dryer is being fixed to a concrete plinth on site, fixing in place is absolutely essential.
Fastenings for floating screed must be supplied by the customer on site.
Fixing to Miele plinth

| Quantity| Screw size
---|---|---
Tensioning strips| 4|
Wood screws DIN 571 (Ø × length)| 4| 8×65 mm
Plugs (Ø × length)| 4| 12×60 mm

If the tumble dryer is being fixed to a Miele plinth (optional accessory available to purchase separately), fixing in place is absolutely essential.
Fastenings for floating screed must be supplied by the customer on site.
Options/Accessories
Miele plinth (optional accessory available to purchase separately)

Concrete base (on site)

The quality of the concrete and its strength must be assessed according to the machine load. The on-site concrete plinth must be fixed adequately to the floor.

Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gutersloh
Germany
Telefon: 05241 89-0
Internet: www.miele.com/professional

References

• Professional

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>