EVOMAGICTUBESET-01 Magic Tube Instruction Manual

EVOMAGICTUBESET-01 Magic Tube

Understanding of P roduct

Security Warning

• When unpacking and before disposing of the carton, check if there is any transportation damage before using the product. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
• Product should install in a cool place. Keep away from the wall 50cm
• Do not install the product or project the beam onto inflammable surfaces. Minimum distance is 5 M
• The product is only intended for installation, operation and maintenance by qualified personnel and read the user manual and labels on the lighting carefully before use
• Do not look directly at the lamp light (especially for epilepsy), so as not to cause damage to the eyes
• Keep the optical system clean. Do not touch the LED lens with bare hands. Do not use any alcohol liquid or any other liquid to clean the optical system. Use medicinal absorbent cotton to clean it.
• Please do not attempt to dismantle and/or modify the product inner structure. Otherwise, would not provide 1 year of free warranty.
• Electrical connection must only be carried out by qualified personnel.
• Before installation, ensure that the voltage and frequency of power supply match the power requirement of the product.
• It is essential that each product is correctly earthed and that electrical installation conforms to all relevant standards.
• Do not connect this device to any other types of dimmer apparatus.
• Make sure that the power cord is never crimped or damaged by sharp edges. Never let the power cord come into contact with other cables. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord
• There is no user serviceable parts inside the product, do not open the housing and never operate the product with the cover removed.
• There are protection structure and circuit for the battery inside the unit, any inappropriate dismount of the light or battery might break the protection function and lead to batter getting hot, smoking, deforming or fire.
• Never short circuit the unit
• Heating and burning will melt the battery separator, causing loss of protection function or burning of electrolyte and overheat will cause heating, smoking, deformation or burning of batteries
• Never use the unit in an environment over 40 not to charge the unit close to fire source or under direct sun. Even never wet or throw the unit to water, otherwise, the protection function inside the batter might lose or abnormal chemical reaction might arise, causing battery to be hot, smoking, deformation or fire
• It is dangerous charging not to use the supplied power adapter
• Never break the light or battery, not to weld the battery or dismount the battery to be used in other equipment, not to touch the leaked battery electrolyte
• Place the unit where kids can’t reach.
• If the charging time over the standard charging time for long, it is advised to stop charging. It will extend the charging time if charging while using, it is advised to turn off the light when charging
• Never place the unit inside microwave oven or any pressure container, instant heating or leakage (or abnormal smell), the unit should be abandoned and treated properly.
• Not to use the unit in an environment where there is static electricity, the battery protection circuit might easily get broken if the static electricity is over 1000V, causing battery working abnormally, heating, smoking, deforming or fire
• When using, keep away of hot source, high pressure, avoid kids, never throw or hit the
• Use the supplied power adapter only, never charging over 24 hours
• When not using the unit for long term, please save the unit properly in a dry place, battery should be half charged.
• Please bury the used unit, never throw to fire or water.

If you have any questions,don’t hesitate to consult our dealer or manufacturer.
Important : Before any installation, maintenance and cleaning, please ensure that the power cut off!

Main Technical Parameters

• Lithium battery
  • Charging Voltage: DC12.6V/2A
  • Battery Specification: 21700 4.2V/4.5Ah*12 cells (12.6V/18Ah)
  • Charge Time: 8~10 hours
  • Circulation Life: Not less than 300 times
  • Run Time Of Battery: Max. 20h
• LED
  • LED Type: 288pcs ×0.3Watts RGBW 4in1 full-color LED
  • Control Pixel: 32 Pixels
  • Rated Power: 50W
  • Colors: 16.7 million colors (0~100% saturation dimming)
  • Life: 50000 hours
• Control
  • Control Protocol: International standard DMX-512 signal
  • Channel Protocol: 7 kinds of control channel mode. 2CH; 4CH; 6CH; 11CH; 32CH -8 Pixels; 64CH -16 Pixels; 128CH -32 Pixels;
  • Control Mode: DMX-512,auto,master-slave,music, infrared remote control,wireless DMX-512 and Mobile APP WIFI control.
  • Wireless Protocol: W-DMX
• Wireless DMX Specs
  • 2.4G Communication Distance: 200M (clearing, it changes vary with different environments)
  • WIFI Communication Distance: 30M (clearing, it changes vary with different environments)
  • Band: 2.4G ISM, 126 channel frequencies
  • Maximum Transmit Power: 20dBm
  • Receiver Sensitivity: -94dBm
• Optical System
  • Dimmer: From 0~100 linear dimming.
  • Flashing Rate: 1~20Hz
  • Beam Angle: 180°
• Physical
  • Dimensions: 052 x 1190 mm
  • Weight: 1.72kg
• Security
  • Cooling System: Convection
  • Waterproof Rate: IP65
  • Temperature Protection: 60°C
  • Operating Environment: Indoor / Outdoor

Product Features

Using the latest LED control technology. The newest intelligent LED pixel tube light can realize intelligent operation and control through its special menu at the back. This product is designed for stage and around event sites and can be used to create stunning lighting effects, it is affordable also very powerful battery LED tube, A highly creative device that offers an infinite range of possibilities. Its main features include:

1. Product built-in lithium battery and the DMX signal wireless module.
2. Product built-in WIFI receiving module, which can be controlled by mobile APP.
3. Wireless DMX with transceiver function.
4. With music control function.
5. Custom color temperature settings.
6. Built-in commonly used film and television shooting effects.
7. With charging protection and current overload protection.
8. Intuitive and convenient battery display function.
9. The static power consumption of the control panel is 0.3W, and its efficiency will reach up to 97% during the process of high power output, which realizes the function of eco-friendly operation.
10. Overheating automatic protection function.
11. IR infrared remote control panel.
12. Touch button and LCD display.
13. Password protected keyboard.
14. 7 kinds DMX working mode.
15. Built-in 68 kinds of Auto effect.
16. Master-slave control, multi-units for synchronous wireless control.
17. Software system updates & upgrades are available through DMX 512 or wireless DMX.

Product Packing Information

Following accessories are packed together with the product, please check them carefully upon unpacking.

Product Installation

DMX Connection Method
When set the DMX512 address code be CH4 MODE, as below:

• Wireless DMX transmitter should be connected to the DMX-512 controller.
• Since CH4 MODE has 4 channels, the address code with 4 increment increasing progressively (e.g., 1,5,9,13…)
• Every DMX address code can be reused as needed.
• DMX address code can be any data between 001 and 512.

2.4G-Wireless Master-Slave Connection Method

As below:

• Set the wireless DMX signal of the first light to the sending state (Master), and the wireless DMX signal of other lights to the receiving state (Slave).
• When the Slave is set to DMX512 control mode, running auto effect or other static colors on the Master to achieve the wireless master-slave synchronization.
• The DMX address code of the Master and Slave can be any data between 001 and 512 without affecting master-slave online.

Mobile APP WIFI Master-Slave Connection Method

As below:

• Establish wireless communication between WIFI control of mobile phone and WIFI control of lights according to 3.5.7.
• Set the wireless DMX signal of the first light to the sending state (Master), and the wireless DMX signal of other lights to the receiving state (Slave).
• When the Slave is set to DMX512 control mode, running auto effect or other static colors on the phone APP to achieve the wireless master-slave synchronization.
• The DMX address code of the Master and Slave can be any data between 001 and 512 without affecting master-slave online.

Operation Method

Back panel functions introduction

2.4G Wireless DMX Connection Method

Working mode
2.4G wireless DMX transceiver uses the WDMX communication protocol which has two working modes Transmit mode and Receive mode.

• Find 【 S et 】 menu and press 【 ENTER 】 to enter system settings menu.
• Press 【 UP/DOWN 】 key to select 【 Wireless 2.4g 】 to enter 2.4g wireless DMX settings menu.
•  WIRELESS 】 for wireless DMX control ON/OFF.【 CONNECT 】 means the paired connection of wireless DMX module. 【 RESET 】 means reset the data of wireless DMX control setting, 【 MODE 】 has transmitting mode and receiving mode.

WORKING

MODE

| ACTION| STATUS DESCRIPTION
---|---|---

W-DMX

Receive

| White| Connection is not established
Red fast flash| Connection is lost
Green fast flash| Connecting to transmitter
Green slow flash| Connected. Without DMX signal
Green| Connected. Receiving DMX signal

W-DMX

Transmit

| Red| Deleting all receivers’ connection
Blue fast flash| Connecting with the Receiver(s)
Blue slow flash| No DMX signal input
Blue| Transmitting DMX signal

Note : The wireless transceiver will remember the chosen protocol even after you disconnecting the power supply. There is no need for repeated setting.

Working mode

• According to step 3.2.1 set the Slave to 【 Receive 】 mode.
• Select 【 Reset 】 menu to reset wireless connection. At this time, the indicator light is white, indicating that the wireless module is not connected to transmit module and is ready to receive the paired signal.
• According to step 3.2.1 set the Master to 【 Transmit 】 mode. At this time, the indicator light is blue slow flash, indicating that the wireless module is not connected to DMX signal.
• Select 【 Reset 】 menu to reset wireless connection. At this time, the indicator light is red, indicating that the connected receiving module is being deleted.
• Select 【 CONNECT 】 to transmit wireless paired signal, at this time the indicator light is blue fast flash.
• When the Slave receive the paired signal from Master, the indicator light is Green fast flash which means the connection is established.

Infrared Remote Controller Instruction

• Dimming up
• Dimming down
• Off light off
• ON light on
• R/G/B /W for 4 single color, A / UV (None)
• 9 number keys meas 9 kinds of static mix colour (AC1……AC9)
• The “0” key for is to enter DMX-512 control state
• AUTO key is color change mode, press up and down key to adjust speed
• STROBE key is in color strobe mode (32 types are optional), press up and down key to adjust speed.
• FADE key is for color fading mode, press up and down key to adjust speed.
• SOUND key is for sound control mode, press up and down key to adjust the sound control sensitivity.
  Note : The IR remote controller should be pointed at the IR infrared receiver. Otherwise, the light will not be controlled.

Menu Display

Menu Overview

DMX Mode

| ****

001–512

|  | ****

DMX address setting and Receive mode

| DMX console

mode

Show

| ****

Auto

| Auto Mode：0-68| 68 kinds of Auto effect| ****

Auto mode

Speed：1-16| 1-16 from slow to fast on speed setting

Color：0-15

| Color setting, 0 for automatic color

change, a total of 15 colors

Sound

| Sound Mode：1-4| 4 sound control modes optional| ****

Sound mode

Sens：1-100| Sound sensitivity setting

Color ：0-15

| Color setting, 0 for automatic color

change, a total of 15 colors

Static

| Dimmer：000-255| Overall dimming| ****

Static color mode

Strobe：000-255| Strobe
Red：000-255| Red dimming
Green：000-255| Green dimming
Blue：000-255| Blue dimming
White：000-255| White dimming

Color

| Red| Cyan| Blue+W| ****

Built in static color mode

Green| Purple| Yellow+W
Blue| Warm White| Cyan+W
White| Red+W| Purple+W
Yellow| Green+W| Full

CCT

| 2800K，3000K，3200K，3500K，3800K，4000K，4500K，5000K，

5600K，6000K，6500K，7000K，7500K，8000K，8500K，9000K，

9500K，10000K

| Color temperature

mode

WIFI

| On the phone, connect WIFI address “Led_XXX” and turn on the

APP【LED LAMP】to control

| ****

WIFI mode

Set

| DMX Channel| 2CH/4CH/6CH/11CH/32CH/64CH/128CH| 7 DMX channel modes
DMX Fail| Hold / Blackout| Status of light fixture after DMX fail
 | Display

Reverse

| OFF / ON| Display Reverse OFF / ON
---|---|---|---
Display On

Time

| 30S / 60S| Display start time
Menu Lock| OFF / ON| When Menu Lock is ON, the button will is locked after 30 seconds without any operation, and press the UP+DOWN

button for 5 seconds to unlock.

IR Remote| OFF / ON| Infrared remote control OFF / ON

Wireless 2.4g

| Wireless| OFF / ON| Wireless DMX OFF / ON
Connect| NO / YES
Reset| NO / YES
Mode| Receive / Transmit
Factory Reset| NO / YES| YES: Restore factory settings

Info

| Name| MAGIC
Version| V1.3

DMX Address Settings ( Dmx512)

• Find 【 DMX Mode 】 menu and press 【 ENTER 】 to enter DMX address code setting.
• Press 【 UP/DOWN 】 button to adjust parameters.
• After setting the DMX address code, p ress 【 ENTER 】 to save the settings

Auto Effect Settings (Auto)

• Find 【 Aut o 】 menu and press 【 ENTER 】 to enter auto effect setting.
• Press 【 UP/DOWN 】 button to select 【 Auto Mode 】 【 Speed 】 or 【 Color 】
• Press 【 ENTER 】 to enter the settings
• Press 【 UP/DOWN 】 button to select auto effect, speed, or color, press 【 ENTER 】 to save the settings.

Sound Effect Settings ( Sound)

• Find 【 Sound 】 menu and press 【 ENTER 】 to enter sound effect setting.
• Press 【 UP/DOWN 】 button to select 【 Sound Mode 】 【 Sens 】 or 【 Color 】
• Press 【 ENTER 】 to enter the settings
• Press 【 UP/DOWN 】 button to select sound effect, sound control sensitivity or color effect, press 【 ENTER 】 to save the settings.

Static Color Settings ( Static)

• Find 【 Static 】 menu and press 【 ENTER 】 to enter static color setting.
• Press 【 UP/DOWN 】 button to select 【 Dimmer 】 【 Strobe 】 【 Red 】 【 Green 】 【 Blue 】 or 【 White 】
• Press 【 ENTER 】 to confirm menu and press 【 UP/DOWN 】 button to adjust parameters, then p ress 【 ENTER 】 to save the settings.

Built-in Static Color Settings ( Color)

• Find 【 Color 】 menu and press 【 ENTER 】 to enter built-in static color setting.
• Press 【 UP/DOWN 】 button to select 【 Red 】 【 Green 】 【 Blue 】 15 built-in colors.
• Press 【 ENTER 】 to save the settings.

Color Temperature Settings ( CCT)

• Find 【 CCT 】 menu and press 【 ENTER 】 to enter color temperature setting.
• Press 【 UP/DOWN 】 button to select 【 2800K 】【 3000K 】【 32 00K 】 … 18 kinds of color temperature effect.
• Press 【 ENTER 】 to save the settings. Hold 【 ENTER 】 for more than 3 seconds to enter the screen for customizing the current color temperature.
• Built-in 【 Red 】 【 Green 】 【 Blue 】 【 White 】 4 base colors with 0~255 brightness adjustment, can freely customize the current color temperature according to your needs.

Mobile APP Control Mode Settings ( WIFI

• Find 【 WIFI 】 menu and press 【 ENTER 】 to turn on WIFI.
• “Led_XXX” displayed on the screen is the WIFI address of the light fixture.
• Scan the above QR code to install 【 LED LAMP 】 APP first on mobile phone.
• On the phone, find WIFI and search WIFI address, and the words beginning with LED appear. For example, “LE D XXX”, click the link
• Turn on the 【 LED LAMP 】 APP installed on the phone and show the link is successful then you can control it.

System Settings ( Set)

• Find 【 Set 】 menu and press 【 ENTER 】 to enter system setting.
• Press 【 UP/DOWN 】 button to select corresponding function setting.
• After setting, press 【 ENTER 】 to save the settings.

Menu Lock Function Menu Lock

• Form 【 Set 】 menu to find 【 Menu Lock 】 menu
• Press 【 ENTER 】 button to enter select 【 ON 】
• When the menu locked, at the same time long press button ▼▲ , the display appears a small lock icon and have a number count down to  “O”, it will unlock successfully.

Charging Display

Note: In the process of charging, the display screen will have a charging display. If the lamp needs to work while charging, press 【 MENU 】 button to enter for operate menu.

Control Channel

DMX Channel Table

2CH 2CH Mode:

Channel| DMX| Data| Control function| Detail description
---|---|---|---|---
1| 0| 255| Overall dimmer| Linear dimming from 0~100%

2

| 0| 10| NO FUNCTION| ****

CCT

11| 24| 2800K
25| 38| 3000K
39| 52| 3200K
53| 66| 3500K
67| 80| 3800K
81| 94| 4000K
 | 95              108| 4500K|
---|---|---|---
109              122| 5000K
123              136| 5600K
137              150| 6000K
151              164| 6500K
165              178| 7000K
179              192| 7500K
193              206| 8000K
207              220| 8500K
221              234| 9000K
235              248| 9500K
249              255| 10000K

4CH 4CH Mode:

6CH 6CH Mode:

2

| 0| 10| ****

Strobe

| NO FUNCTION
11| 255| From slow to fast(1HZ-20HZ)
3| 0| 255| Red dimmer| Linear dimming from 0~100%
4| 0| 255| Green dimmer| Linear dimming from 0~100%
5| 0| 255| Blue dimmer| Linear dimming from 0~100%
6| 0| 255| White dimmer| Linear dimming from 0~100%

11CH 11CH Mode:

Channel| DMX| Data| Control function| Detail description
---|---|---|---|---
1| 0| 255| Overall dimmer| Linear dimming from 0~100%

2

| 0| 10| ****

Strobe

| NO FUNCTION
11| 255| From slow to fast(1HZ-20HZ)

3

| 0| 10| ****

Static macro

| NO FUNCTION
11| 255| 17 values for each color

4

| 0| 16| ****

Macro background color

| NO FUNCTION
17| 255| 17 values for each color
5| 0| 255| Macro background color brightness| Linear dimming from 0~100%
 | 0| 10| ****

Macro

| NO FUNCTION
11| 220| 3 values for each macro effect

6

| 221| 228|  | Sound control mode 1
---|---|---|---|---
229| 236| Sound control mode 2
237| 244| NO FUNCTION
245| 255| Sound control mode 3
7| 0| 255| Macro speed| From slow to fast
8| 0| 255| Red dimmer| Linear dimming from 0~100%
9| 0| 255| Green dimmer| Linear dimming from 0~100%
10| 0| 255| Blue dimmer| Linear dimming from 0~100%
11| 0| 255| White dimmer| Linear dimming from 0~100%

32CH 32CH Mode:

64CH 64CH Mode:

128CH 128CH Mode:

Maintenance

Product Maintenance
To prolong the life of the product, it is very important to do maintenance work. The environment is hash outdoors, or if the product is idle for a long time, damp, smoke or particularly dirty surroundings can cause greater accumulation of dirt on its LED lens cover, fan vents and housing. So it should be cleaned to maintain an optimum light output and at the same time to prevent it from corrupted by acid gas. Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning products should be used for cleaning. It is recommended to clean product at least one every 20 days.

Friendly Notice : Please do not use any organic solvent, e.g.alcohol to clean housing of the apparatus, le st cause damage.

Trouble Shooting

The product doesn’t switch on

| The battery is dead. Charging it.
Power supply is damaged or abnormal. Call a qualified personnel to fix it.
Control section is damaged. Call a qualified personnel to fix it.
Connection of internal circuitry is not correct. Call a qualified personnel to fix it.
The product can turn on, but LEDs do not emit

light and are out of control

| DMX address is wrongly setting up. Resetting it according to instruction book.
DMX Signal wrongly connected. Connect it correctly according to instruction book.
Control section is damaged. Call a qualified personnel to fix it.
The beam appears dim| The product is too hot. Take ventilation measures to make it cool.

Remark : This product warranty for one year. We provide pay needed maintenance service after the warranty. But because of natural and man-made disasters or improper operation caused damage not under warranty range.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>