BOLIN PD910 Series Dante AV-H Decoder Instruction Manual
- June 1, 2024
- BOLIN
Table of Contents
BOLIN PD910 Series Dante AV-H Decoder
Specifications
- Model No.: EG40DH
- Decoder (Video Output): Dante AV-H, AVC-H.264 / HEVC-H.265
- Codec Platform: Hardware FPGA-enhanced HEVC codec for FAST HEVC
- Video Resolutions:
- 3840 x 2160P @60/59.94/50/30/29.97/25/24/23.98
- 1920 x 1080P @60/59.94/50/30/29.97/25/24/23.98
- 1920 x 1080i @60/59.94/50
- 1280 x 720P @60/59.94/50
- Color Space(HDMI): –
- Audio Formats: –
- Video Streaming Latency: Results may vary depending on network configuration and management settings
- Bandwidth: Results may vary depending on network configuration and management settings
- Ecosystem Friendly
- Video IP IN: –
- Highest Resolution: –
- Highest Frame Rate: –
- Video Codec: –
- Video Format: –
- HDMI & SDI Codec: Decoder only
Product Usage Instructions
Dante Ecosystem Compatibility
- The EDGE Series Dante AV-H Decoder is designed to seamlessly integrate with the Dante ecosystem, providing compatibility with Dante AV-H cameras, encoders, mixers, and other audio devices.
Video Output Options
- The decoder offers HDMI and SDI outputs, allowing for simultaneous connection to monitors or vision mixers.
IP Decode Support
- The decoder supports FPGA decoding for various IP streams including RTSP, SRT, MPEGTS, HEVC, and FAST HEVC, ensuring compatibility with a wide range of cameras and decoders.
Audio Support
- The TRRS audio intercom on the front panel enables live production intercom functionality.
Dante Controller Integration
- Utilize the Dante Controller software for device discovery, management, routing, monitoring, and firmware upgrades, providing a user-friendly experience.
Video Upscaling and Power Options
- The decoder can upscale lower-resolution video to a maximum of 4K60 output and supports flexible power options including POE+ and 12VDC input.
Mounting Options
- The compact form factor allows for versatile mounting options such as rack mount, DIN rail, panel/wall mounts, VESA mounts, and tripod support.
FAQ
Q: Can the decoder handle audio embedded in the video output?
A: Yes, the decoder supports up to eight channels of audio essences embedded in the video output.
Q: What video formats and standards are supported by the decoder?
A: The decoder supports various resolutions including 3840 x 2160P, 1920 x 1080P, 1920 x 1080i, and 1280 x 720P, along with HDMI and SDI outputs.
Q: Does the decoder support Dante AV-H cameras?
A: Yes, the decoder is fully compatible with all Dante AV-H cameras and encoders within the Dante ecosystem.
EDGE Series Dante AV-H™ Network Video Decoder
- Dante AV-H is a software solution for SoC-based video products that brings the power and interoperability of Dante to H.26x video endpoints.
- Dante AV-H is less complicated and more flexible to install than point-to-point solutions and with low bandwidth, it’s the ideal AV solution for today’s networks.” (Audinate.com)
- Bolin EG40DH is a powerful FPGA-engineered IP decoder capable of receiving a single Dante AV-H video flow over a standard 1GB network and outputting up to 4K60 with embedded Dante audio through HDMI 2.0 and 12G-SDI. It is compatible with all
- Dante AV-H cameras and Dante audio devices. In addition, the EG40DH can decode RTSP IP streams via HEVC, and FAST HEVC, making it compatible with Bolin’s FAST HEVC cameras and decoders.
- Dante AV-H uses the industry standard H.264/H.265 codecs, offering excellent image quality and low bandwidth across the network. Dante AV-H video and audio routing and configuration are managed with the familiar, reliable, easy-to-use Dante Controller software. The EG40DH can also take advantage of Dante Domain Manager’s robust management and user access control.
- Dante AV-H flows can co-exist with Dante AV Ultra flows on the same network, providing excellent video quality with lower bandwidth.
- The EG40DH is a powerful, reliable option for decoding video flows from Dante AV-H PTZ cameras or PCs running Dante Studio software for output to monitors or Vision Mixers to swap between multiple sources.
Bolin Dante AV-H Decoder Workflow
Dante Ecosystem Friendly
- Full compatibility with all existing and future Dante-enabled products.
- Discovery, routing, and management with the familiar and reliable Dante Controller software Dante Studio, and Dante Viewer.
- Compatible with Dante Domain Manager
- Operates on a standard 1GB network infrastructure.
- Can Co-exist with Dante AV Ultra flows on the same network (Dante AV-H devices can only be subscribed to other Dante AV-H devices.)
- Perfect for Houses of Worship, Video Conferencing, Education, Live Performance, Hospitality, Green Rooms, and any situation where excellent quality, low bandwidth, and Dante compatibility are required.
OUTPUT
OVERVIEW
- Up to 4K60 video over standard Gigabit Ethernet
- 2 channels of Dante audio embedded with video
- Low latency, low bandwidth video performance
- HDMI 2.0 and 12G-SDI output
- Video upscalable max from 720P up to 4K60 (UHD)
- Discoverability, routing, and management with Dante Controller software
- Supports unicast and multicast for video and audio flows with separately routable audio and video streams.
- Seamless integration with existing Dante audio or Dante AV networks
KEY FEATURES
High Quality, Low Bandwidth Video Output
- The EG40DH outputs up to 4K60 video with low latency and very low bandwidth (±50 Mb) across the Dante AV network, giving customers additional flexibility and network management options.
Dante AV-H™ and Dante Audio Compatible
- Full compatibility with all Dante AV-H cameras and encoders and all Dante-enabled Mixers, audio devices, and encoders, with support for up to eight channels of audio essences embedded in the video output.
HDMI and SDI Output
- Support for simultaneous HDMI 2.0 and 12G-SDI outputs to monitors or Vision Mixers.
IP Decode Support
- FPGA decoding support for RTSP, SRT, MPEGTS IP streams, HEVC, and FAST HEVC, making it compatible with Boliln’s FAST HEVC cameras, decoders, and all standard HEVC streams.
Production Audio Support
- TRRS Audio intercom on the front provides support for live production intercom.
Full Dante Controller Support
- Device discovery, management, routing, monitoring, and firmware upgrades are enabled through the familiar and reliable Dante Controller software, providing a simple, plug-and-play experience.
Video Upscalable
- Upscales lower resolution HDMI and SDI video to the maximum from 720P up to 4K60 (UHD) output. Downscaling is available.
Flexible Power Options
- Support for POE+ power over the network and 12VDC power input (supplied).
Convenient Mounting Options
- The small, 1/3RU form factor offers a variety of horizontal and vertical mounting options, including rack mount, DIN rail, panel and wall mounts, VESA mounts, and tripod support.
Video Format and Standard
Full Format
- 3840 x 2160P 60/59.94/50/30/29.97/25/24/23.98
- 1920 x 1080P 60/59.94/50/30/29.97/25/24/23.98
- 1920 x 1080i 60/59.94/50
- 1280 x 720P 60/59.94/50
Upscalable
- Max From 720P Up to 4KP60
SDI Standard
- SMPTE 292(1.5Gb/s)
- SMPTE 424
- SMPTE 425-A(3Gb/s)
- SMPTE 2081(6Gb/s)
- SMPTE 2082-0/1(12Gb/s) with SMPTE 352 SDI Metadata
Dante AV-H™ / FAST HEVC / HEVC
- EG40DH Dante AV-H decoder Decodes
- Dante AV-H – when used within the Dante AV-H environment
- HEVC – when used with any SoC HEVC IP cameras
- FAST HEVC – when used with Bolin’s FAST HEVC cameras to gain ultra-low latency
FPGA-Based FAST HEVC Platform
- Instead of an SoC, the EG40DH utilizes Bolin’s FPGA-based FAST HEVC platform to provide a higher level of performance:
- Dual output 12G-SDI and HDMI 2.0 video with independent resolution setup
- Upscaling from low resolution up to UHD (4K60) video output, in addition to decoding 4K60 IP streaming
- Ultra-low latency when used with Bolin’s FAST HEVC camera
SPECIFICATIONS
Model No. | EG40DH |
---|---|
Decoder (Video Output) | HDMI & SDI |
Codec
Encoder/Decoder| Decoder only
Video Codec| Dante AV-H, AVC-H.264 / HEVC-H.265
Codec Platform| Hardware FPGA-enhanced HEVC codec for FAST HEVC
Video Resolutions| 3840 x 2160P @60/59.94/50/30/29.97/25/24/23.98
1920 x 1080P @60/59.94/50/30/29.97/25/24/23.98
1920 x 1080i @60/59.94/50
1280 x 720P @60/59.94/50
Color Space(HDMI)| 4K60: RGB 8bit, YUV4:4:4 8bit, YUV4:2:2 12bit,
4K30 & below: RGB 8bit/10bit, YUV4:4:4 8bit/10bit, YUV4:2:2 12bit
Audio Formats| 3.5mm Jack, analog audio, stereo (unbalanced); audio intercom,
Line out – HDMI audio output
Video Streaming| 1 stream
Latency (Results may vary depending on network configuration and management
settings)| <4 frame ( <70 ms between encoder and decoder)
Bandwidth
(Results may vary depending on network configuration and management settings)
| 4K60 4:2:2/12bit; 20-60Mbps
1080p60 4:2:2/12bit; 10-35Mbps
Ecosystem Friendly| Dante AV-H, Instant Dante Ecosystem compatibility with
existing Dante AV-H enabled products; Unified control of audio and video using
Dante tools – Dante Controller
Video codec is compatible with standard AVC/HEVC, H.264/265, or Dante AV-H to
output video without having ultra-low latency; Pair with Bolin’s Fast HEVC
camera or encoder to decode output extremely low latency video.
Video
Video| Highest Resolution| Up to 4K (3840×2160)
Highest Frame Rate| Up to 60
IP IN| Video Codec| Dante AV-H,AVC-H.264 / HEVC-H.265
Video Format| 3840 x 2160P @60/59.94/50/30/29.97/25/24/23.98
1920 x 1080P @120/60/59.94/50/30/29.97/25/24/23.98
1280 x 720P @60/59.94/50
Frame Rates (Hz)| 23.98, 24, 25, 30, 29.97, 50, 59.94, 60
Application Protocols| Dante AV-H,RTP, RTSP. MP2TS over UDP, TS over RTP, TS
over SRT, HTTP, IGMP v1/v2, DHCP, SSH,
802.1X Authentication
Multi-stream| 1 stream
HDMI OUT| Format| HDMI 2.0
Supported Resolutions| 3840 x 2160P 60/59.94/50/30/29.97/25/24/23.98
1920 x 1080P 120/60/59.94/50/30/29.97/25/24/23.98
1920 x 1080i 60/59.94/50
1280 x 720P 60/59.94/50
Upscaling| Yes, upscale from 720P up to FHD, and from FHD to 4K60 resolution
Frame Rates (Hz)| 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
Color Space| 4K60: RGB 8bit, YUV444 8bit, YUV422 12bit,
4K30 & below: RGB 8bit/10bit, YUV444 8bit/10bit, YUV422 12bit
SDI OUT| Format| 12G-SDI
Supported Resolutions| 3840 x 2160P @60/59.94/50/30/29.97/25/24/23.98
1920 x 1080P @60/59.94/50/30/29.97/25/24/23.98
1920 x 1080i @60/59.94/50
1280 x 720P @60/59.94/50
Upscaling| Yes, upscale from 720P up to FHD, and from FHD to 4K60 resolution
Frame Rates (Hz)| 23.98, 24, 25, 29.97, 30, 50, 59.97, 60
Color Space| YUV422 10bit
Standard| SMPTE 292(1.5Gb/s), SMPTE 424, SMPTE 425-A(3Gb/s), SMPTE 2081, SMPTE
2082-0/1 With SMPTE352 SDI
Metadata Supported
Audio
Audio Transport Formats| Audio Compression| AAC-LC, MPEG-2
Audio S/N Ratio| ≥85dB
Audio THD+N| ≤0.05%
Audio Noise (RMS)| ≤-90dB
Bit Depths| AAC-LC, MPEG-2 (sampling rate: 48KHz/44.1KHz, 24bit, 64-256Kbps
selectable)
Intercom| MIC / Headset| Reserved
Output Signal Types| Embedded Audio over
HDMI
| Stereo 2-channel, Dante AV-H ( Audio Flow x 4 Flows / 2 Channels per Flow)
Embedded Audio over SDI| Stereo 2-channel
Format| PCM
Line-out| 3.5mm Jack, analog Line-out
Communication/Connector
Ethernet| Ethernet General| Standard 1Gbps Ethernet
Auto-switching, auto-negotiating, auto-discovery, full/half duplex
Ethernet with PoE| IEEE 802.3at compliant 1000BASE-T Ethernet port
IEEE 802.3at Type 3 compliant, PoE+ Class 4
HDMI OUTPUT (Decoder only)| HDMI 2.0 Type-A connector, female; HDMI digital
video/audio output
SDI OUTPUT| BNC| 75Ω
PTZ Camera IR Receiver| Front and Back, bidirectional
LED Indicator| Power| Yes, board powered and active (Bolin Logo corner)
Codec| Yes, video codec active
Low latency| Yes, light up for low latency mode
System| Yes, system status
Control| Interface| –
Protocol| Bolin Restful API
System Firmware Upgrade| Upgrade via the IP web interface or Dante Controller
for Dante AV-H
Reset| Yes, long press for 5 seconds to reset
Power| Power Input| 12V DC, 2A
Power Button| Yes
Connector Type| 5.5mm×2.1mm Male DC Power Plug Connector & Screw Lock Female
Panel Socket Mount Adapter
Interface| HDMIx1, SDIx1, 12V DC power portx1, Power switchx1, Reset buttonx1,
RJ45x1 (LAN/PoE+), Infrared Receiverx2 (front & back), Line outx1, Intercom
Mic inputx1, LED Indicatorx3
General
Power| Power Consumption| 18W
PoE| PoE+, IEEE 802.3at Type 3 class 4 compliant
Power Adaptor| 12V DC, 2A
12V DC IN has priority over Ethernet PoE. Ethernet PoE will become active a
fraction of a second after 12V DC IN is
disconnected.
Storage Temperature| -40° to 60° C (-40°F to 140°F)
Operating Temperature| 0° to 50° C (32°F to 122°F)
Humidity| 10% to 90% (non-condensing)
Heat Dissipation| Cooling fan, 3 Level – Automatically adjust the fan speed
according to the temperature
Acoustic Noise| NC35 or less, variable with cooling fan speed adjustment
Dimension| 14215044mm (LxDxH), 14215050.5mm(with feet mats)
Net Weight| 1.05kg (2.31lb)
Enclosure
Chassis| Metal, black finish, heat dissipation surface, fan cooled; vented
front and rear
Mounting| Included| HDMI cable secure mount, Base mount
Optional| 19″ Single-rack mount, 19″ Tri-rack mount, Din rail mount, Surface
mount
Size of Screw Hole for Tripod| 1/4”
What’s Included| Decoderx1, Power Adapter x1 & Power Cord x3 (US, EU, UK),
Thank You Card x1
ORDER INFORMATION
- EG40DH (HDMI 2.0+12G-SDI) Decoder
- Included: • B-BM10 (Base Mount)
- B-SM10 (Surface Mount)
Optional
- B-RM20 (Single-Rack Mount)
- B-RM22 (Dual-Rack Mount)
- B-RM23 (Tri-Rack Mount)
- B-DR10 (Din Rail Mount)
INSTALLATION MOUNT
- Rack Mount
- Base Mount
- Surface Mount
- Pole Mount
- Din Rail Mount
- Tripod Mount
ACCESSORY
Items marked * are optional to purchase
DIMENSIONS
- All models and specifications are subject to change without notice.
- All brand names and registered trademarks are the property of their respective owners.
- www.bolintechnology.com
Documents / Resources
|
BOLIN PD910 Series Dante AV-H
Decoder
[pdf] Instruction Manual
PD910 Series Dante AV-H Decoder, PD910 Series, Dante AV-H Decoder, AV-H
Decoder, Decoder
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>