THULE 307134 LED Strip Sideways 4m Instructions
- June 1, 2024
- THULE
Table of Contents
THULE 307134 LED Strip Sideways 4m
Product Information
Specifications
- Manufacturer: Thule
- Contact Email: infoRV@thule.com
- Website: www.thule.com
Product Usage Instructions
Installation
- Open the packaging and check that all parts are included.
- Follow the step-by-step guide provided in the user manual for installation.
- Secure the product following the recommended safety guidelines.
Operation
To operate the product:
- Ensure the product is correctly installed.
- Refer to the user manual for specific operation instructions.
- Practice using the product in a safe environment before full use.
Maintenance
Regular maintenance is essential for product longevity:
- Clean the product with a damp cloth and mild detergent.
- Check for any loose parts or damage regularly.
- Store the product in a dry and secure place when not in use.
Frequently Asked Questions
- Q: How do I contact customer support for this product?
- A: You can reach out to Thule customer support via email at infoRV@thule.com or visit their website for more information.
- Q: Is there a warranty for this product?
- A: Please refer to the warranty information provided in the user manual or on Thule’s website for details on product warranty.
Read this installation instruction and the safety instructions in the appendix thoroughly. No guarantee will be allowed for damages caused by wrong installation or operation.
WARNINGS
- Installing the LED strip should strictly be executed by professionals.
- It is mandatory to install the LED strip in such a way that it cannot be used with running vehicle engine. Driving around with shining LEDs is illegal.
- Preferably install the LED strip away from direct sunlight. Continuous exposure to direct sunlight will cause discolouring.
- Operate with 12V DC only.
INSTALLATION
- The LED strip can be cut to a desired length, in steps of 50mm. Cut only when the LED strip is disconnected. Cut only between the dots as indicated above. Seal the cut-off edge with silicone or shrink wrap.
- Before placing the LED strip, make sure the surface is clean, free of dust and grease.
- Peel off the protective sheet from the back of the strip and position the LED strip.
USAGE
- When using a high-pressure cleaner, keep at least 30cm distance from the LED strip.
SAFETY INSTRUCTIONS
Read these safety instructions thoroughly, before installing and starting up the device and store it in a safe place. If the device is handed over to another person, this manual is to be handed over along with it.
INSTALLATION
The electronic device may only be installed by qualified personnel from a
specialist company (in Germany in accordance with VDE 0100, Part 721).
The following information is intended for specialists who are familiar with
the guidelines and safety precautions to be applied
Caution!
Safety instruction: failure to observe this instruction can cause material damage or personal injury and impair the proper functioning of the device.
Caution!|
Safety instruction relating to the danger emanating from electrical currents or voltage: failure to observe this instruction can cause material damage or personal injury and impair the proper functioning of the device.
The manufacturer will not be held liable for claims for damage resulting from the following:
- Faulty assembly or connection
- Damage to the appliance resulting from mechanical influences and excess voltage
- Alterations to the device without express permission from the manufacturer
- Use for purposes other than those described in the operating manual
Warning!
To prevent short circuits, always disconnect the negative terminal of the electrical system before working on the vehicle. If the vehicle has an additional battery, its negative terminal should also be disconnected.
Warning!
Inadequate supply cable connections could result in short circuits with the consequence that:
- cable fires occur
- the airbag is triggered
- electronic control devices are damaged
- electric functions fail (indicators, brake light, horn, ignition, lights)
INSTALLING & CONNECTING THE POWER CABLE
Thule NV recommends that you connect the power cable to the fuse box or terminal block and not directly to the battery; Choose the safest and shortest installation route for the power cable. Shorten the power cable as required.
Caution!
- Only use cable clips that are suitable for the diameter of the power cable for the connection to the fuse box, terminal block or battery. If the wrong terminals are used, it could cause a voltage drop and increase heat formation at the terminal.
- Use the correct fuse to the connection with the vehicle’s power supply according to the wiring diagram and according EN 1648-1 & EN 1648-2.
Caution!
Installing the wrong fuse can cause cable fire in case of a short circuit or
malfunction!
If the length of the supplied power cable is not sufficient, the connection
cable must be replaced with a new connection cable with a larger cable
diameter.
Thule NV is not responsible for any misprints. This instruction may be changed
without prior notice. We do not accept responsibility for any possible errors
in the content
Product Overview
Installation Instructions
Contact
- Thule NV, Kortrijkstraat 343 – BE 8930 Menen, BELGIUM
- infoRV@thule.com
- www.thule.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>