OzSpy Spy Shop NIHV2000 Night Vision Binocular User Manual
- June 1, 2024
- OzSpy Spy Shop
Table of Contents
- Congratulations
- ◆ Accessories
- ◆Over View
- ◆Battery Installation
- ◆Inserting / Removing the SD card
- ◆Instructions for Use
- Turning off the Night Vision device
- ◆Focusing the image
- ◆Key functions
- ◆LCD screen information
- ◆Using the zoom function
- ◆Using IR light in complete darkness
- ◆Transmitting videos and photos to your computer
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OzSpy Spy Shop NIHV 2000 Night Vision Binocular
Congratulations
Congratulations on your purchasing this high quality night vision device. The
device can be used not only during the day but also in low light conditions or
in complete darkness with the built-in infrared light.
You can take pictures and video which can be stored on a micro SD card. Use
the supplied USB cable to connect your computer and download the images to
your computer. You can view, delete, move, or copy any videos and photos.
◆ Accessories
Night Vision Device
USB Cable
Neck Strap
Storage Pouch
User Manual
◆Over View
Parts overview (Fig.1)
- Infrared filter cap
- Objective focus
- USB port
- Micro-SD card slot
- Mode button
- Power button
- IR button
- Snap-button
- Zoom-button
- Ocular
- AA Battery case
- AA Battery case
- Tripod adapter
◆Battery Installation
Open battery compartments and install the 8×AA batteries each being sure to follow the polarity markings inside the battery compartment. Close the battery cover.
◆Inserting / Removing the SD card
Insert the micro SD card into the micro SD card port and push until it locks in place. To remove the inserted micro SD card, please push the micro SD card inward to release it. Storage capacity: 4GB to 32GB is recommended
Note : If you do not insert the micro SD card, the device will show the icon “ ”
◆Instructions for Use
Power On : Press the [Power] button still for about 4seconds to start the
Night Vision device.
Taking Photo : Press [MODE] button and select the photo mode. The icon “
” will appear in the top left corner of the screen. Press the [SNAP] button to
take photos.
Taking Video : Press [MODE] button and select the video mode. The icon “
” will appear in the top left corner of the screen. Press the [SNAP] button to
start recording video. Press the [SNAP] button again to stop recording.
Note : When in bright conditions, please cover the objective lens with
attached IR-filter cap.
When using device in dark conditions, please remove the IR-filter cap.
Browsing Videos and Photos:
Press the [MODE] button and select playback mode. Press [IR] button to switch
photos or videos. Press [SNAP] button to play/stop video.
Deleting/Protect Videos and Photos:
In playback mode, press the [ZOOM] button to set up. Press [IR] button to
select delete/protect, press [SNAP] to confirm. Press [SNAP] again to confirm
delete/protect.
If you want to cancel delete/protect, press [ZOOM] button can back to playback
interface.
Turning off the Night Vision device
Press the [Power] button for about 3 seconds to turn off the Night Vision device.
◆Focusing the image
Target the object you would like to view and turn the object-focusing ring located just below the objective lens until the image on the screen comes sharp and clear.
◆Key functions
【MODE】 | Video / Photo / Playback In 【Menu】 【Setup】 mode: Up |
---|---|
【SNAP】 | In video mode: Press it to take video. Press it again to stop |
recording. In photo mode: Press it to take photo. In playback mode: Play and
stop Video In 【Menu】【Setup】mode: OK/Confirm
【ZOOM】| In video mode: Press it to zoom out. In photo mode: Press it to
zoom out. In playback mode: Press it once into 【Setup】 mode. Press it continue
twice into【Menu】mode. Press【ZOOM】button again to exit.
【IR】| In Video/Photo mode: Press it to turn on the infrared light. With
each additional click, the IR brightness will increase. In playback mode:
Press it to switch the video and picture. In 【Menu】【Setup】 mode: Down
◆LCD screen information
The screen display in video mode:
1
| Taking video
---|---
2
| Recording time
3
| Zoom
4
| Intensity the brightness of IR from 1 to 4 while using the battery, Intensity the brightness of IR from 1 to 4 while plug in the USB power.
5
| Micro card
6
| Battery power
7
| Date and time
The screen display in photo mode:
1 | Taking photo |
---|---|
2 | Zoom |
3 | Intensity the brightness of IR from 1 to 4 while using the battery, |
Intensity the brightness of IR from 1 to 4 while plug in the USB power.
4| Micro Card
5| Battery power
6| Date and time
The screen display during 【Setup】 interface:
On playback interface, press [ZOOM] button once can enter [Setup] interface.
Delete|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
---|---
Protect|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
The screen display during 【Menu】 mode:
On playback interface, continuously press [ZOOM] button twice can enter [Menu] interface.
Video Resolution|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
---|---
Photo Resolution|
IR/MODE->Select SNAP->OK ZOOM ->Esc
White Balance|
IR/MODE–>Select SNAP ->OK ZOOM->Esc
Exposure|
There are thirteen exposures for your choice. IR/MODE ->Select SNAP ->OK ZOOM ->Esc
---|---
Record Audio|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Date Stamp|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Date/Time|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Auto Power Off|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Power saving mode: The NV can be set to automatically shut down when not
operating after the selected period of time.
Screen Saver|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Language|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Frequency|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Bright|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
---|---
Format|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Default Setting|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
Version|
IR/MODE ->Select SNAP ->OK ZOOM ->Esc
◆Using the zoom function
The zoom function can be used while taking video or photo. Press the [ZOOM] button to select 6x digital zoom.
◆Using IR light in complete darkness
The IR light can be used in complete darkness environment.
Press the [IR] button to activate the infrared light and remove the IR Lens
cover.
Press the [IR] button to select between the 4 levels of brightness.
◆Transmitting videos and photos to your computer
Using a USB cable, you can connect the night vision device with your computer. You can find the photo/video files on the computer by looking under “My computer/removable disk”. When the night vision connects your computer, you can view, delete, move, or copy any videos and photos.