Sunco Lighting DL-SL4-NL-WH-2750K 4 Slim Selectable Nightlight User Manual
- June 1, 2024
- Sunco Lighting
Table of Contents
Sunco Lighting DL-SL4-NL-WH-2750K 4 Slim Selectable Nightlight
Product Details
- Voltage: 120V
- Wattage: 11W
- Wattage Equivalency: 110W
- Beam Angle:
- Weight: 0.55lbs
- Housing Material: Aluminium
- Dimmable: Yes
- Model: P-PKG1WB-WH MACL-153M-WH PD-6WCL-WH AYCL-153P-WH DVCL-153P-WH D26HD-2RW HS220 HS220P3
Product Usage Instructions
Before You Start
Safety Information: To reduce the risk of fire, electric shock, or physical injury, follow these guidelines:
- This device complies with Part 15 of the FCC rules.
- This device must accept any interference that may cause undesired operation.
- Review all instructions carefully before installation.
Quickstart Guide
- Use the template to cut the hole.
- Connect supply & junction wires.
- Attach fixture to junction box.
- Insert fixture into ceiling.
Installation Guide
STEP 1:
- a. Turn off the circuit breaker before installation.
- b. Cut out 4.33 housing size on the Installation Template, then tape it onto the ceiling in the desired location.
- c. Cut ceiling hole using the Installation Template as a guide.
FAQ
We’ve got you covered! Our troubleshooting section is here to shed some light and provide you with easy-to-follow solutions for any problem.
Installation:
- The light isn’t turning on.
- If the light isn’t turning on, double-check if the fixture is properly connected and ensure that the circuit breaker hasn’t been tripped.
- The light isn’t bright enough.
- If the light isn’t bright enough, make sure to check for proper wattage and ensure that the fixture is unobstructed.
- Dimming Light not dimming to the lowest setting.
- If the light is not dimming to the lowest setting, check the proper wattage and ensure that the minimum dimmer load requirement is met.
Whats in the Box?
Nightlight Selectable
Get Your Gear
Before You Start
Safety Information
To reduce the risk of fire, electric shock, or physical injury:
- Turn off the circuit breaker before installing this fixture.
- Professional installation is required. Safety gear is recommended.
- Abide by regional and local laws or regulations.
- Proper grounding is required to ensure safety.
- Do not alter, or remove wiring during installation.
- Do not make or alter any open holes in the wiring enclosure or electrical components during installation.
- Check for shipping damage before insatalling. If the product is damaged, do not use it.
- Keep fixture away from corrosive substances.
- Suitable for damp locations at temperatures ranging from 4°F to 113°F. Not for use where directly exposed to water.
- Clean the fixture regularly to ensure proper operation. Do not clean with harsh solvents.
- Use safety precautions and abide by regional and local laws or regulations.
- This product is not compatible with 3rd party sensors.
- This product is not compatible with photo controls.
- This product is not compatible with occupancy sensors.
- This product is not compatible with timing devices.
FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference that may cause undesired operation. Please review all instructions carefully before installation.
Quickstart Guide
- Step 1
- Use the template to cut the hole.
- Step 2
- Connect supply & junction wires
- Step 3
- Attach fixture to junction box.
- Step 4
- Insert fixture into ceiling.
Installation Guide
- STEP 1
- a. Turn off the circuit breaker before installation.
- b. Cut out the 4.33” housing size on the Installation Template, then tape it onto the ceiling in the desired location.
- c. Cut ceiling hole using the Installation Template as a guide.
- STEP 2
- a. Open the junction box and remove the appropriate knockout.
- STEP 3
- a. Connect supply and junction wires using wire nuts:
- Black to Black (Live)
- White to White (Neutral)
- b. Tuck connected wires inside the junction box & close the cover.
- STEP 4
- Slide the CCT Selection Switch to choose from five color temperatures. Insert the junction box through the ceiling hole.
- a. New Construction Applications: Secure to studs, joists, or similar fixed structural units.
- b. Remodel Applications: Do not require secure studs, joists, or similar fixed structural units.
- STEP 5
- a. Attach the fixture to the junction box using the connector as shown in the image (1). Tighten the connector by hand (2).
- b. Push up spring clips and insert fixture into ceiling. Turn on the circuit breaker and test the light.
- STEP 6
- Note: To toggle between the downlight and the nightlight, turn the wall switch and the night light off, wait 3 seconds, then switch on.
- To reset the fixture, turn it off, wait 5 seconds, then turn it on.
Product Details
Recommended Dimmers
| Brand | Model |
|---|---|
| LUTRON | P-PKG1WB-WH |
| LUTRON | MACL-153M-WH |
| LUTRON | PD-6WCL-WH |
| LUTRON | AYCL-153P-WH |
| LUTRON | DVCL-153P-WH |
| LEVITON | D26HD-2RW |
| KASA SMART | HS220 |
| KASA SMART | HS220P3 |
Scan for the full compatible dimmer list!
Specifications
Common Troubleshooting
- We’ve got you covered! Our troubleshooting section is here to shed some light and provide you with easy-to-follow solutions for any problem.
- If you still need some assistance, feel free to contact us. Our team of lighting experts is happy to help brighten your day.
Light Distribution Angle
Downlight Mode
- AVERAGE BEAM ANGLE (50%): 133.4 DEG
- C0/180: 144.8°
- C90/270: 122.0°
- UNIT: cd Luminous Intensity Distribution 1
Nightlight Mode
- AVERAGE BEAM ANGLE (50%): 96.5 DEG
- C0/180: 103.2°
- C90/270: 89.8°
- UNIT: cd Luminous Intensity Distribution 1
- Lighting distribution angle refers to the spread of light emitted from a light source. It is an important factor to consider when selecting a fixture or bulb, as it affects the way it will illuminate an area.
- There are two main types of lighting distribution angles: A symmetric lighting distribution emits light evenly in all directions, creating a cone-shaped pattern that provides a pool of light.
- This type of lighting is ideal for general lighting and illuminating large areas. Common applications for symmetric lighting include general area illumination, security lighting, and perimeter lighting.
- Symmetric lighting is also used to a certain degree in up-lighting. An asymmetric lighting distribution angle, also known as a beam angle, creates a pattern that focuses light in a specific direction.
- This type of lighting is ideal for task lighting as it reduces glare and light spills in other areas. Common applications include task lighting in spaces such as landscape settings, retail stores, museums, and much more.
- It is important to note that the lighting distribution angle can also be affected by other factors such as the reflector design of the light source, the type of lens used, and the distance between the light source and the surface being illuminated.
Customer Support
Warranty Policy
- This product is covered by our industry-leading 7-year warranty.
- It gets even better – scan the QR code for 2 extra years of protection!
30-Day Return Policy
- At Sunco we value our customers and stand by the quality and performance of our products.
- If you are not completely satisfied with your purchase, we accept returns within 30 days of your purchase date.
Customer Service
- Our Los Angeles team of lighting experts is here to assist you with all your needs! Contact us at:
- Email: support@sunco.com
- Text or Call: 844-334-9938 6AM – 6 PM PST Monday – Friday
- support@sunco.com
- 844-334-9938
Documents / Resources
|
Sunco Lighting DL-SL4-NL-WH-2750K 4 Slim Selectable
Nightlight
[pdf] User Manual
DL-SL4-NL-WH-2750K 4 Slim Selectable Nightlight, DL-SL4-NL-WH-2750K, 4 Slim
Selectable Nightlight, Selectable Nightlight, Nightlight
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>