MAGIC FX PART01085 Smokejet User and Installation Installation Guide

MAGIC FX PART01085 Smokejet User and Installation Installation Guide

WARNING
Read this manual carefully before installing and/or using this product. Failure to read the manual and to follow the printed instructions may lead to personal injury and/or damage to the product.
© 2019 MAGICFX® All rights reserved.

Nothing from this publication may be copied, reproduced and/or published by means of printing, photocopying or by any other means, without the prior written approval of MAGIC FX.
MAGIC FX reserves the right to modify specifications stated in this manual.

TRADEMARKS

Any brand names mentioned in this manual are registered trademarks of their respective owners.

LIABILITY

MAGIC FX accepts no liability for claims from third parties arising from unauthorised use, use other than that stated in this manual, and use other than in accordance with the General Conditions registered at the Chamber of Commerce.
We further refer to the General Conditions. These are available on request, free of charge.
Although considerable care has been taken to ensure a correct and comprehensive description of all relevant components, the manual may nonetheless contain errors and inaccuracies.
Should you detect any errors or inaccuracies in the manual, we would be grateful if you would inform us. This helps us to further improve our documentation.

FOREWORD

Congratulations! You have bought a great new product from MAGIC FX. This manual contains all information required for the intended use of the equipment. Deviation from the described intended use can result in a hazardous situation and/or property damage.
This manual includes notes and warnings on safe operation of the equipment. These notes and warnings are accompanied by the following icons. Read them attentively!

DANGER
Indicates a hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations.
WARNING
Indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
NOTICE
Indicates information considered important, but not hazardrelated (e.g. messages relating to property damage).
LANGUAGE
This document contains the original instructions in English. In case you require other languages please contact MAGIC FX.

REVISION TABLE

Doc nr| Revision| Date| Description| Author| Approved
---|---|---|---|---|---
PART01085| 01-00| 20-08-2018| Initial release| TVA| WH
PART01085| 01-02| 04-01-2021| New design| NE| LL

SAFETY INFORMATION

WARNING
Please read the following safety information carefully before operating the machine. Information includes important safety information about installation, usage, and maintenance. Pay attention to all warning labels and instructions in this manual and printed on the machine.

• If you have questions about how to operate the machine safely, please contact your local MAGIC FX dealer for help.
• Keep this device dry.
• Always connect to a grounded circuit to avoid risk of electrocution.
• Before connecting machine to power, always check voltage indicate on machine match to your local AC voltage. Do not use the machine if AC power voltage does not match.
• Disconnect the machine from AC power before servicing and when not in use.
• This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts, immediately unplug the machine and contact your local MAGIC FX dealer for advice.
• No user serviceable and modifiable parts inside. Never try to repair this product, unauthorized technician may lead machine to damage or malfunction.
• For adult use only. Never leave the machine running unattended.
• Installed in well ventilated area. Provide at least 50 cm space around the machine.
• Never add flammable liquid of any kind to the machine.
• Make sure there are no flammable materials close to the machine while operating.
• Only use MAGIC FX fluid. Other fluid may lead to heater clog and malfunction.
• If the machine fails to work, unplug the machine and stop operationimmediately. Contact your local MAGIC FX dealer for advise.
• Before transporting the machine, make sure the fluid tank is completely drained.
• Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it securely. In case of eye contact or if fluid is swallowed immediately look for medical advice.

MAIN PARTS

TECHNICAL DATA

13.6 in
Width| 193 mm                                        7.6 in
Height| 386 mm                                        15.2 in
Weight ** Weight| 11.1 kg (dry) 13.6 kg (full)          24.5 lb / 30 lb
Electrical| Voltage Input| 230 – 250 Vac
Voltage Frequency| 50 – 60 Hz
Power Consumption| 1420 W
Power Connector| Neutrik® powerCON TRUE1 (in & out)
Usage| Consumable(s)| MAGICFX® SMOKEJET fluid
Consumable Consumption| ** MAGICFX® SMOKEJET fluid 2.5 ml/s

PRODUCT IDENTIFICATION
MAG:CFX
MFX0901-SMOKEJET
Weight : 11.1kg / 24.5lb.
Power: 230Vac 50-60Hz 1420W
Breaker: 9A 250V
Build date: 2101
Serial: 00000

ACCESSORIES

Please contact MAGIC FX for additional possibilities.

FX FLUIDS

The MAGICFX® SMOKEJET uses MAGICFX® SMOKEJET FLUID to create the smoke effect. The fluid is delivered in a can. Do not use other fluids than those that are approved and supplied by MAGIC FX, see following table.

OPERATE SAFELY!

WARNING
Please read the following safety information carefully before operating the machine. Information includes important safety information about installation, usage, and maintenance. Pay attention to all warning labels and instructions in this manual and printed on the machine.

If you have questions about how to operate the machine safely, please contact your local MAGIC FX dealer for help.

GENERAL SAFETY RULES

• Keep this device dry.
• Always connect to a grounded circuit to avoid risk of electrocution.
• Before connecting machine to power, always check voltage indicate on machine match to your local AC voltage. Do not use the machine if AC power voltage does not match.
• Disconnect the machine from AC power before servicing and when not in use.
• This product is for indoor use only! Do not expose to rain or moisture. If fluid is spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts, immediately unplug the machine and contact your local MAGIC FX dealer for advice.
• No user serviceable and modifiable parts inside. Never try to repair this product, unauthorized technician may lead machine to damage or malfunction.
• For adult use only. Never leave the machine running unattended.
• Installed in well ventilated area. Provide at least 50 cm space around the machine.
• Never add flammable liquid of any kind to the machine.
• Make sure there are no flammable materials close to the machine while operating.
• Only use MAGIC FX fluid. Other fluid may lead to heater clog and malfunction.
• If the machine fails to work, unplug the machine and stop operation immediately. Contact your local MAGIC FX dealer for advise.
• Before transporting the machine, make sure the fluid tank is completely drained.
• Smoke fluid may present health risks if swallowed. Do not drink smoke fluid. Store it securely. In case of eye contact or if fluid is swallowed immediately look for medical advice.

RIGGING

Please follow the European and national guidelines for safe rigging and trussing.

SAFETY SYMBOLS

| Read the manual carefully before use!

PRECAUTIONS FOR OPERATION
WARNING
Using a damaged or an improper installed machine can lead to death, serious injury or property damage. Always inspect the machine thoroughly before operation.
WARNING
Unauthorized operation of the machine can lead to death, serious injury or property damage. Never leave the machine unattended when the machine is ready for use
WARNING
Do not use the MAGICFX® SMOKEJET if alterations have been   made other than by or on behalf of MAGICFX
WARNING
Make sure there are no objects near the input grill that can block  the air to be sucked in.
CAUTION
Always follow the instructions as noted on the cans.
CAUTION
Missing or obscured safety symbols on the machine can lead to death, serious injury or property damage. Make sure all safe
NOTICE
Do not use other fluids than those that are approved and supplied by MAGIC FX, see Section 1.5.

SETTING UP

INSTALL THE MACHINE

1. Place the machine on a flat surface and in a suitable large area with at least 50 cm open space around the machine.

2. Fill the fluid tank with MAGICFX® approved fluid.

3. Connect the machine to suitable rated power supply. To determine the power requirement for the machine refer to the label on the back of the machine.
   WARNING Always connect the machine to a protected circuit and ensure it is properly grounded to avoid risk of electrocution.

4. Turn on the machine and allow it to heat up. Heat up takes approximatly 5 mintues. Once the machine has reached operating temperature, the LCD display will show “Ready To Fog”. Now the machine is ready for operation

5. To start making fog, locate the OUTPUT button on the control panel, and press the button to start making fog.

6. To turn off the machine, press STOP button and turn POWERCON TRUE1 to the OFF position.

OPERATION

CONTROL PANEL OPERATION

The machine can be operated with the onboard digital control interface.

CONTROL MENU

DMX512
Address: 1
Set DMX address from 1 to 504
Stand Alone
Set Master
Set machine as Master of Slave unit
Color Mode
On
Turn LED On or Of
Color Mode
Macro: 01
Set LED output color from macro 1 to 10
Color Mode
Chase: 01
Set LED chase from 1 to 15
Timer
Interval 15 Sec
Set interval from 15 to 360 seconds
Time
Duration 5 Sec
Set duration from 1 to 5 seconds
Wireless Setting
On
Turn On or Off wireless control
Wireless Setting
Button A:M01
Set wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
Wireless Setting
Button C:M01
Set wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
Wireless Setting
Button D:M01
Set wireless remote button function macro color 1 to 10 or chase 1 to 15 and off.
LED Setting
Fog Only
Setting for LED to turn on with fog only or always on.
LED Fade Out
Delay: 0 Sec
Set LED delay time from 0 to 5 seconds.
Run Last Setting
On
Turn On/Off run last setting function
2 Second Jet Mode
Off
Turn On/Off 2 Second Jet Mode
W-DMX512
Off
WiredDMXcontrol:W-DMX512 OFF
WirelessDMXcontrol :W-DMX512 ON
W-DMX Rest
Off
Reset W-DMX connection.

WIRELESS OPERATION.
Wireless remote control system consists of a transmitter equipped with four buttons to activate four user configurable LED setting and fog; with an onboard receiver attached to the rear panel of SmokeJet

**Remote

Wireless Receiver

**

Wireless settings are configurable through onboard control panel, refer to control menu section to setup each buttons.
In a free open space the effective distance is 50 meters, actual usage depending on obstacle level the effective distance is 10-25 meters.

REGISTERING TRANSMITTER.
Transmitter can be paired or deleted from the receiver. Each receiver can pair up to 10 transmitters. Follow the steps below to pair or delete transmitter from receiver.

1. Power off SMOKEJET
2. Press and hold [DOWN] button
3. Turn power on and release [DOWN] button when LCD display blinks
4. Follow the menu instruction to pair or delete transmitter

TRANSMITTER BATTERY REPLACEMENT.
If the effective distance seems to be decreased, it is possible that the battery level is low and requires a replacement. In order to replace the battery, undo the three screws on the back of transmitter to release the cover. Replace with same batterytype and specification of battery which is 27A-12V.
DMX CONNECTOR PIN ASSIGNMENT
The machine provides 5 pin XLR connector for DMX connection. Diagram below indicate pin assignment information.

DMX CHANNEL FUNCTION

CLEAN UP

• Do not allow the machine to become contaminated.
• Remove dust from air vents with air compressor, vacuum or a soft brush.
• Only use a damp cloth to clean the casing.
• Before storing run distilled water through the system to help avoid condensing the pump or heater.
• It is recommended to run the machine on a monthly basis in order to achieve best performance and output condition.
• Excessive dust, liquid and dirt built up will degrade performance and cause overheating.

MAINTENANCE

To achieve the maximum service life of the MAGICFX® SMOKEJET you must regularly clean the MAGICFX® SMOKEJET and test if it is functioning correctly.
Contact MAGIC FX if the MAGICFX® SMOKEJET is not functioning correctly.

DANGER
Do not replace parts yourself; always consult MAGIC FX

TROUBLESHOOTING

Always contact MAGIC FX if any malfunctions or errors occur that cannot be solved with the instructions as described in this manual.
BREAKER RESET
Breaker
230V = 9A 250V

WARNING
Disconnect AC power before reset breaker. Only replace fuse with same type and rating

1. Disconnect AC power
2. Flip breaker to ON position
3. Turn on machine to test

FAQ
Why does the machine not respond on any wired DMX input? Make sure the W-DMX512 is turned OFF.

CORRECT DISPOSAL

This symbol on the product and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product to designated collection points where it will be accepted free of charge.
Alternatively, in some countries you may be able to return your products to your local retailer upon purchase of an equivalent new product.
Disposing of this product correctly will help save valuable resources and prevent any potential negative eff ects on human health and the environment, which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

EC DECLARATION OF CONFORMITY

According to Annex III A Machinery Directive 2006/42/EC
MAGIC FX B.V. declares as manufacturer and composer of the technical construction file that the product with the following specifications:

Name machine : SMOKEJET
Type : MFX0901
Voltage : 230–250 Vac 50-60Hz
Serial number : on product
Year of construction : on product

Is in conformity with the minimal safety regulations as stated in the following directive(s):

• LVD (2014/35/EU) Low Voltage Directive
• EMC (2014/30/EC) ElectroMagnetic Compatibility
• RoHS (2011/65/EU) Restriction of the use of certain Hazardous Substances
• WEEE (2012/19/EU) Waste Electrical & Electronic Equipment

The following harmonized standards were applied:

• NEN-EN-ISO 12100:2010 Safety of machinery – General principles for design – Risk assessment and risk reduction.
• NEN-EN-IEC 60204-1:2018, Safety of machinery – Electrical equipment of machines – Part 1: General requirements.
• NEN-EN-IEC 61000-6-3:2007/A1:2011, Electromagnetic compatibility (EMC) – Part 6 3: Generic standards – Emission standard for residential, commercial and light-industrial environments.

Original declaration of conformity
Translation of the original declaration of conformity

Name manufacturer : MAGIC FX BV
Address : Schouwrooij 27, 5281 RE BOXTEL
Country : The Netherlands
CEO : B. Veroude
Date : 4-1-2021

Signature :

Documents / Resources

| MAGIC FX PART01085 Smokejet User and Installation [pdf] Installation Guide
PART01085 Smokejet User and Installation, PART01085, Smokejet User and Installation, User and Installation, Installation
---|---

References

• MAGIC FX - Mind blowing special effects - MAGIC FX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>