TP-Link DS105GP Omada 5-Port Gigabit Unmanaged Desktop Switch Instruction Manual

TP-Link DS105GP Omada 5-Port Gigabit Unmanaged Desktop Switch

Product Information

Regulatory Compliance
This product complies with FCC Rules and meets the following conditions:

• This device may not cause harmful interference.
• This device must accept any interference received.

CE Mark Warning
Class A product that may cause radio interference in a domestic environment. Compliance with EU directives.

UKCA Mark Warning
Class A product that may cause radio interference in a domestic environment. Compliance with UK regulations.

Contact Information

• Responsible Party: TP-Link USA Corporation
• Address: 10 Mauchly, Irvine, CA 92618
• Website: https://www.tp-link.com/us/
• Tel: +1 626 333 0234
• Fax: +1 909 527 6804
• E-mail: sales.usa@tp-link.com

Product Usage Instructions

Specifications

• Model: T120100-2B1
• For use with: DS116GE/ TL-SG116/ TL-SG116E/ S4500-8G/ SG2008/ T1500G-8T/ TL-SG2008
• Power Adapter Model: T535081-2-DT (For TL-SF1005LP/ TL-SF1008LP/ TL-SG1005LP)
• Responsible Party: TP-Link USA Corporation

Installation

1. Place the switch in a well-ventilated area.
2. Connect the power adapter to the switch and plug it into a power outlet.
3. Connect your network devices to the switch using Ethernet cables.

Operation

1. Power on the switch by pressing the power button.
2. Check the indicator lights to ensure proper functioning.
3. Configure your network settings as needed.

Maintenance

• Regularly check for dust accumulation and clean the switch if necessary.
• Avoid exposing the switch to extreme temperatures or moisture.
• Keep the switch firmware updated for optimal performance.

FAQs

• Q: What should I do if the switch is not powering on?
  A: Check the power adapter connection and try plugging it into a different outlet. If the issue persists, contact customer support.

• Q: How do I reset the switch to factory settings?
  A: Locate the reset button on the switch, press and hold it for at least 10 seconds until the indicators flash. Release the button to reset the switch.

Switch
© 2023 TP-Link 1910013525 REV2.0.0

For Class A switch with power adapter:

FCC Compliance Information Statement

• Product Name: Switch
• Model Number: DS105GP/ DS106GPP/ DS106P/ DS108GP/ DS110GMP/ DS110GMP2C/ DS111P/ DS116GE/ LS105GP/ LS105LP/ LS106LP/ LS108GP/ LS109P/ LS1210GP/ TL-SF1005LP/ TL-SF1005P/ TL-SF1006P/ TL-SF1008LP/ TL-SF1008P/ TL-SF1009P/ TL-SG1005LP/ TL-SG1005P/ TL-SG1006PP/ TL-SG1008P/ TL-SG105MPE/ TL-SG105PE/ TL-SG105PP-M2/ TL-SG108PE/ TL-SG116/ TL-SG116E/ TL-SG116P/ TL-SG1210MP/ TL-SG1210MPE/ TL-SG1210P/ TL-SG1210PP/ TL-SG605P/ TL-SG608P/ TL-SL1311MP/ TL-SL1311P/ S4500-8G/ S4500-8GP/ S4500-8GP2F/ S4500-16GP/ SG2008/ SG2008P/ SG2210XMP-M2/ SG2016P/ SG2210P/ T1500G-8T/ TL-SG2008/ TL-SG2008P/ TL-SG2016P/ TL-SG2210P/ ES205GP/ ES210GP

SG605P/ TL-SG608P/ TL-SL1311P/ S4500-8GP/
| S4500-8GP2F/ SG2008P/ SG2210P/ TL-SG2008P/ TL-SG2210P/
| ES205GP)
| T535243-2-DT (For DS110GMP/ DS110GMP2C/ TL-SG105MPE/
| TL-SG105PP-M2/ TL-SG116P/ TL-SG1210MP/ TL-SG1210MPE/
| TL-SG1210PP/ TL-SL1311MP/ S4500-16GP/ SG2016P/ TL-
| SG2016P/ ES210GP)
| T535337-2-DT (For SG2210XMP-M2)

Responsible party:
TP-Link USA Corporation.

• Address: 10 Mauchly, Irvine, CA 92618
• Website: https://www.tp-link.com/us/
• Tel: +1 626 333 0234
• Fax: +1 909 527 6804
• E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• Product Name: Power Adapter
• Model Number: T535081-2B4/ T535081-2-DT/ T535131-2-DT/ T535243-2-DT/ T535337-2-DT Responsible party:
• TP-Link USA Corporation.
  • Address: 10 Mauchly, Irvine, CA 92618
  • Website: https://www.tp-link.com/us/
  • Tel: +1 626 333 0234
  • Fax: +1 909 527 6804
  • E-mail: sales.usa@tp-link.com
• This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
• Product Name : Power Adapter
• Model Number: T120100-2B1
• Responsible party:
  • TP-Link USA Corporation.
  • Address: 10 Mauchly, Irvine, CA 92618
  • Website: https://www.tp-link.com/us/
  • Tel: +1 626 333 0234
  • Fax: +1 909 527 6804
  • E-mail: sales.usa@tp-link.com

FCC

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  • This device may not cause harmful interference.
  • This device must accept any interference received, including interference that may cause undesired operation.
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
  Issue Date: 2023/11/17

CE Mark Warning

• This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
• TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.
• The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce

UKCA Mark Warning

• This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
• TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
• The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)

Safety Information

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Keep the device away from water, fire, humidity or hot environments.
• Place the device with its bottom surface downward.
• For switch powered by power adapter:
  • Do not use damaged charger or USB cable to charge the device.
  • Do not use any other chargers than those recommended.
  • Adapter shall be installed near the equipment and shall be easily accessible.
  • Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us.
• For switch powered by power cord:
  • Plug the product into the wall outlets with earthing connection through the power supply cord.
  • The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.
  • The socket-outlet shall be installed near the equipment and shall be easily accessible. For switch powered by USB or standard PoE:
  • This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label

Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products.

Wall Mounting Requirements

• For LS105GP/ LS108GP/ LS1210GP/ TL-SG105PP-M2/ TL-SG1210PP:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 7.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

• For DS110GMP/ DS110GMP2C/ DS111P/ DS116GE/ TL-SG116/ TL-SG116E/ TL-SG116P/ TL-SG1210MP/ TL-SG1210MPE/ TL-SL1311MP/ TL-SL1311P/ ES210GP:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

• For TL-SG105PE/ TL-SG605P:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 7.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

• For DS105GP/ DS106GPP/ DS106P/ DS108GP/ LS105LP/ LS106LP/ LS109P/ TL-SF1005LP/ TL-SF1005P/ TL-SF1006P/ TL-SF1008LP/ TL-SF1008P/ TL-SF1009P/ TL-SG1005LP/ TL-SG1005P/ TL-SG1006PP/ TL-SG1008P/ TL-SG105MPE/ TL-SG108PE/ TL-SG608P/ S4500-8G/ S4500- 8GP/ S4500-8GP2F/ S4500-16GP/ SG2008/ SG2008P/ SG2210XMP-M2/ SG2016P/ SG2210P/ T1500G-8T/ TL-SG2008/ TL-SG2008P/ TL-SG2016P/ TL-SG2210P:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

• For ES205GP:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# standard and are more than 10 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4.5 mm.

For Class A switch with no power adapter:
FCC Compliance Information Statement

• Product Nam e: Switch
  Model Number: DS1008X/ DS1016G/ DS1018GMP/ DS1024G/ DS1016GE/ DS1024GE/ TL- SF1016/ TL-SF1016DS/ TL-SF1024/ TL-SF1024D/ TL-SF1048/ TL-SG1005P-PD/ TL- SG1008/ TL-SG1008MP/ TL-SG1016/ TL-SG1016D/ TL-SG1016DE/ TL-SG1016PE/ TL- SG1024/ TL-SG1024D/ TL-SG1024DE/ TL-SG1024S/ TL-SG1048/ TL-SG1218MP/ TL- SG1218MPE/ TL-SG1428PE/ TL-SL1218MP/ TL-SL1218P/ TL-SL1226P/ TL-SX1008/ S4500-8GHP2F/ S5500-8MHP2XF/ S5500-8XF/ S5500-16XF/ S5500-24F4XF/ S5500-24GP4F/ S5500-24GP4XF/ S5500-24MPP4XF/ S5500-48GP4F/ S5500- 48GP4XF/ SG2005P-PD/ SG2210MP/ SG2218/ SG2218P/ SG2428P/ SG3210/ SG3210XHP-M2/ SG3210X-M2/ SG3218XP-M2/ SG3428/ SG3428MP/ SG3428X/ SG3428XF/ SG3428X-M2/ SG3428XMP/ SG3428XPP-M2/ SG3452/ SG3452P/ SG3452X/ SG3452XP/ SL2428P/ SX3008F/ SX3016F/ SX3032F/ SX3206HPP/ TL-SG2210MP/ TL-SG2218/ TL-SG2218P/ TL-SG2428P/ TL-SG3210/ TL-SG3210XHP-M2/ TL-SG3428/ TL-SG3428MP/ TL-SG3428X/ TL-SG3428XF/ TL-SG3428X-M2/ TL-SG3428XMP/ TL-SG3428XPP-M2/ TL-SG3428X-UPS/ TL-SG3452/ TL- SG3452P/ TL-SG3452X/ TL-SG3452XP/ TL-SL2428P/ TL-SX3008F/ TL-SX3016F/ TL- SX3206HPP/ SG6428X/ SG6428XHP/ SG6654X/ SG6654XHP/ SX6632YF/SG2428LP
  *For SG6428XHP & SG6654XHP, if the pluggable power supply module PSM900-AC is used in in countries/regions using low voltage (e.g. Canada, Colombia, Costa Rica, Dominican Republic, Ecuador, El Salvador, Guatemala, Honduras, Japan, Mexico, Panama, Puerto Rico, Taiwan (China), and United States), please note that the module needs up to 12A AC input when the input voltage is 100-120V (included). In other countries/regions, the AC input requirement is 120 (not included)-240V~ 50/60Hz 10A.
• Responsible party:
  • TP-Link USA Corporation
  • 10 Mauchly, Irvine, CA 92618
  • Website: https://www.tp-link.com/us/
  • Tel: +1 626 333 0234
  • Fax: +1 909 527 6804
  • E-mail: sales.usa@tp-link.com
• This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  • This device may not cause harmful interference.
  • This device must accept any interference received, including interference that may cause undesired operation.
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

CE Mark Warning

• This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
• TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.
• The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce

UKCA Mark Warning

• TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
• The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/

Canadian Compliance Statement

• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
  • This device may not cause interference.
  • This device must accept any interference, including interference that may cause undesired operation of the device.

Industry Canada Statement
CAN ICES-3 (A)/NMB-3(A)

Safety Information

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

• Place the device with its bottom surface downward.

• Keep the device away from water, fire, humidity or hot environments.
  Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid. (Only for SG2005P-PD)

• Plug the product into the wall outlets with earthing connection through the power supply cord.

• The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.

• The socket-outlet shall be installed near the equipment and shall be easily accessible.

• This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1. (Only for switch powered by USB or standard PoE)

• Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device.

• Please use this product with care and operate at your own risk.

• Please be cautious if the following two symbols are found in your product.

Explanation of the symbols on the product label
Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products.

For Class B switch with power adapter

FCC Compliance Information Statement

Product  Name: Switch
Model Number: DS105G/ DS105G-M2/ DS105X/ DS108G/ DS108G-M2/ DS105GE/ DS108GE/ LS1005/ LS1005G/ LS1008/ LS1008G/ LS105G/ LS108G/ TL-SF1005D/ TL- SF1008D/ TL-SF1016D/ TL-SF1024M/ TL-SG1005D/ TL-SG1008D/ TL-SG105/ TL-SG105E/ TL-SG105-M2/ TL-SG105S/ TL-SG105S-M2/ TL-SG108/ TL-SG108E/ TL-SG108-M2/ TL- SG108S/ TL-SG108S-M2/ TL-SG605/ TL-SG605E/ TL-SG608/ TL-SG608E/ TL-SX105/ ES205G

Responsible party:
TP-Link USA Corporation

• Address: 10 Mauchly, Irvine, CA 92618
• Website: https://www.tp-link.com/us/
• Tel : +1 626 333 0234
• Fax: +1 909 527 6804
• E-mail: sales.usa@tp-link.com

Note

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• Product Name: Power Adapter
• Model Number: T050060-2B1 / T090060-2B1 / T090060-2I1 / T120100-2B1 / T120200-2B1
• Responsible party:
  • TP-Link USA Corporation
  • Address: 10 Mauchly, Irvine, CA 92618
  • Website: https://www.tp-link.com/us/
  • Tel: +1 626 333 0234
  • Fax: +1 909 527 6804
  • E-mail: sales.usa@tp-link.com
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

CE Mark Warning

• This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
• TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
• The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce

UKCA Mark Warning

• This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
• TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
• The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)

Safety Information

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Keep the device away from water, fire, humidity or hot environments.
• For metal-shell switch:
  • Place the device with its bottom surface downward.
• For switch powered by power adapter:
  • Do not use damaged charger or USB cable to charge the device.
  • Do not use any other chargers than those recommended.
  • Adapter shall be installed near the equipment and shall be easily accessible.
  • Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’t hesitate to contact us. (For switch powered by power adapter)
• For switch powered by power cord:
  • Plug the product into the wall outlets with earthing connection through the power supply cord.
  • The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.
  • The socket-outlet shall be installed near the equipment and shall be easily accessible. For switch powered by USB or standard PoE:
  • This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label
Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products.

Wall Mounting Requirements

• For TL-SG1005D:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# standard and are more than 10 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4.5 mm.

• For TL-SG1008D:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# standard and are more than 10 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4 mm.

• For DS105G-M2/ DS105X/ DS108G-M2/ DS105GE/ DS108GE/ LS105G/ LS108G/ TL-SG105E/ TL-SG105-M2/ TL-SG105S-M2/ TL-SG108E/ TL-SG108-M2/ TL-SG108S-M2/ TL-SG605E/ TL-SG608E/ TL-SX105:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 7.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

• For LS1005G/ LS1008G:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 2.5 mm.

• For TL-SF1016D:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6# standard and are more than 9 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 3 mm.

• For DS105G/ DS108G/ TL-SG105/ TL-SG105S/ TL-SG108S/ TL-SG605:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 7.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

• For TL-SG108/ TL-SG608:
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4#, (5#), 6#, 8# standard and are more than 8.5 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 1.5 mm.

• For ES205G
  To mount the device on a wall, use 2 screws which complies with ANSI B1.1 4# or 6# standard and are more than 11 mm in length. When the screws are fixed on the wall, the distance between the screw head and the wall should be more than 4.5 mm.

References

• Link: Simple, secure one-click payments
• TP-Link Product Support - Wireless Networking Equipment Support
• Regulatory Compliance | TP-Link
• WiFi Networking Equipment for Home & Business | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>