eufy T8214 Video Doorbell with Chime User Guide

eufy T8214 Video Doorbell with Chime

AT A GLANCE

Front View

1. LED Light
2. Motion Sensor
3. Primary Camera Lens
4. Microphone
5. Ambient Light Sensor
6. LED Ring / Doorbell Button
7. LED Light
8. Secondary Camera Lens
9. Speaker
   

Rear View

1. Detaching Mechanism

2. Power Terminals for Existing Doorbell Wires (Optional)

3. SYNC Button
   Press to turn on the doorbell.
   Press and hold for 2 seconds until you hear a beep to set up the doorbell. (Optional)
   Press quickly 5 times within 3 seconds to turn off the doorbell.

4. Battery Compartment

5. QR Code (Scan to add the doorbell in the app
   

Doorbell Chime

1. SYNC Button

2. Speaker

3. microSD Card Slot
   Insert a microSD* to store recordings (Optional)

4. Status LED

5. Reset Hole

6. Power plug (varies by region)
   *Use at least a Class 10 microSD card with a maximum of 128 GB.
   

HOW THE SYSTEM WORKS

Works with Doorbell Chime

The video doorbell detects motion at your porch and lets you to answer the door anytime, anywhere. The WiFi doorbell chime works as an indoor digital chime and stores video clips on a microSD card (not included). When someone rings the doorbell, people in the house will be notified.

Works with eufy Security Home Base (Optional)

The video doorbell detects motion at your porch and lets you to answer the door anytime, anywhere. You can store video clips in the built-in storage of your eufy Security Home Base 2 or S380 Home Base (sold separately). When someone rings the doorbell, people in the house will be notified.

POWERING ON THE WI-FI DOORBELL CHIME

1. Attach the power connector to the doorbell chime.
   

2. Plug the doorbell chime into a wall outlet at your desired location. The LED indicator turns solid green when the doorbell chime is ready for setup.

CHARGING THE BATTERY PACK

1. Remove the pre-installed battery pack from the battery compartment.

2. Fully charge the rechargeable battery pack before installation.

3. Place the battery pack into the battery compartment.

SETTING UP THE SYSTEM

1. . Download and install the eufy Security app, then sign in or create an account.
   |
   ---|---
   

2. Follow the in-app instructions to add the video doorbell and the Wi-Fi doorbell chime.

DETERMING THE POWER OPTION

Option 1: Battery Powered

If you don’t have existing doorbell wiring at your front door, use the included battery. You are free to determine the location of the doorbell, and the mounting will be easy and quick.
When the battery is low, you will need to recharge it. Battery life varies with use. If you choose this option, please skip to DOORBELL MOUNTING (Battery Powered).

Option 2: Wire Powered

If you have existing and working doorbell wires at your front door, the video doorbell will be constantly powered by these wires. So there’s no need to detach and recharge after installation.

The mounting position is limited. If you choose this option, please skip to DOORBELL MOUNTING (Wire Powered).

DOORBELL MOUNTING (Battery Powered)

Choose a Location

1. Take the video doorbell to your front door and check the live view in the app. Choose a location where you can see the desired field of view. Consider the following factors:

   • Check if you can reuse the existing holes and anchors in the wall or door frame.
   • If you want to place the doorbell near a side wall, make sure the wall isn’t in the field of view. Otherwise, the IR light will be reflected and the night vision will be blurred.
   • If you are drilling the mounting holes for the first time, the recommended height is 48″ (1.2m) above the ground.
   • To adjust the angle, use the 15º mounting wedge as a supplementary mounting bracket.
     

2. Place the screw hole positioning card against the wall to mark the location. If mounting on a hard wall (brick, concrete, or stucco), use a 15/64″ (5.95mm) drill bit to drill 2 holes through the screw hole positioning card.
   

What you need: Phillips-Head Screwdriver; Power Drill (15/64″ Drill Bit)

Mount the Bracket

Use the provided screws to secure the mounting bracket on the wall.

Wooden Wall

• Without 15º Mounting Wedge

• With 15° Mounting Wedge

Hard Wall

• Without 15º Mounting Wedge

• With 15° Mounting Wedge

Install the Doorbell

Align the doorbell with the bottom of the mounting bracket, then press the top of the doorbell into place until it clicks.

Recharging the Battery

1. Insert the detaching pin into the pin hole on the top of the doorbell, then lift the top for removal.
   

2. Repeat steps in “CHARGING THE BATTERY PACK”.

You can purchase an extra battery pack for quick replacement.

DOORBELL MOUNTING (Wire Powered)

Check the Doorbell Wires

1. Ring the existing doorbell to check if it is working. If it doesn’t ring, your doorbell wires may be defective. Power on the doorbell by the built-in battery or consult an electrician to repair the wires.
2. Shut off the power at the circuit breaker. Turn the lights on and off to make sure the electricity in your home is properly shut off.

Always be careful when handling wires. If you’re not comfortable installing it yourself, have a qualified electrician to do it.

Detach the Existing Doorbell Button

If you already have existing doorbell wiring:

1. Remove the existing doorbell button with a Phillips-head screwdriver (not provided).
2. Pull the two wires out carefully when removing the existing doorbell. Straighten the wire ends if necessary.
   

Choose a Location

1. Take the video doorbell to your front door and check the live view in the app. Choose a location where you can see the desired field of view. Consider the following factors:
   

   • Check if you can reuse the existing holes and anchors in the wall or door frame.
   • If you want to place the doorbell near a side wall, make sure the wall isn’t in the field of view. Otherwise, the IR light will be reflected and the night vision will be blurred.
   • If you are drilling the mounting holes for the first time, the recommended height is 48″ (1.2m) above the ground.
   • To adjust the angle, use the 15º mounting wedge as a supplementary mounting bracket.
     

2. Place the screw hole positioning card against the wall to mark the location. If mounting on a hard wall (brick, concrete, or stucco), use a 15/64″ (5.95mm) drill bit to drill 2 holes through the screw hole positioning card.
   

What you need: Phillips-Head Screwdriver; Power Drill (15/64″ Drill Bit)

Mount the Bracket

Use the provided screws to secure the mounting bracket on the wall.

Wooden Wall

• Without 15º Mounting Wedge

• With 15° Mounting Wedge

Hard Wall

• Without 15º Mounting Wedge

• With 15° Mounting Wedge

Connect the Wires to the Doorbell

Connect the wires to the terminals on the back of the doorbell, then tighten the terminal screws. Wire can be connected to any terminal.

To prevent short-circuiting, make sure the wires are not touching each other after connecting them to the terminals.

If the wires are too short, use the extension wires and wire nuts to make them longer. Use electrical wiring tape instead if there is no more space on the wall for wire nuts.

Install the Doorbell

Align the doorbell with the bottom of the mounting bracket, then press the top of the doorbell into place until it clicks.

Restore Power

Switch the main circuit breaker back to ON. You’re all set!

SAFETY

• The suitable temperature for T8214 and accessories is -20°C to 50°C (Charging temperature is 0°C to 40°C).
• The suitable temperature for T8023 and accessories is 0°C to 40°C .
• Unless specifically indicated that it is safe to do so in the user guide or instruction manual, do not use this device in an environment that exceeds the recommended low or high temperature.
• Unless specifically indicated that it is safe to do so in the user guide or instruction manual, avoid exposing your device to direct sunshine or excessively wet environments.
• It is recommended to charge the device in an environment with a temperature that ranges from 5°C to 25°C.
• When charging, place the device in an environment that has a normal room temperature and good ventilation.
• For pluggable equipment, the socket-outlet shall be easily accessible.

CAUTION!
THERE IS A RISK OF EXPLOSION IF AN INCORRECT BATTERY TYPE IS USED.
DISPOSE OF USED BATTERIES ACCORDING TO THEIR INSTRUCTIONS.

Warning:

• Replacing a battery with an incorrect type may bypass safeguards and create danger;
• Disposal of a battery in a fire or other source of significant heat, or by crushing, or cutting, may result in an explosion as well as leakage of flammable liquids and gases;
• Leaving a battery in an extremely hot environment may result in an explosion as well as leakage of flammable liquids and gases;
• A battery subjected to extremely low air pressure may result in an explosion as well as leakage of flammable liquids and gases.

NOTICE

Declaration of Conformity

This product complies with the radio interference requirements of the European Community.

Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the
Web site: https://uk.eufylife.com/.

This product complies with the radio interference requirements of the United Kingdom.

This product complies with the radio interference requirements of the United Kingdom.
Hereby, Anker Innovations Limited declares that this product is in compliance with Radio Equipment Regulations 2017(SI2017/1206). The full text of the UK declaration of conformity is available at the following internet address: https://uk.eufylife.com.
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United Kingdom

Your product is designed and manufactured with highquality materials and components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information on the disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

RF exposure information:

The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use product that maintains a 20cm distance between the device and the human body.
Frequency bands and power as below:

The following importer is the responsible party (contract for EU matters):
Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807 Munich, Germany
The following importer is the responsible party (contract for UK matters):
Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United Kingdom

CUSTOMER SERVICE

Kunde service
12-month limited warranty
(US) +1 800-988-7973
support@eufy.com
Anker Innovations Limited
@EufyOfficial
@EufyOfficial
@EufyOfficial

References

• eufy | Built with Care | Up to 53% Off | eufy UK
• eufy | Built with Care | Up to 53% Off | eufy UK
• eufy | Built with Care | Up to 53% Off | eufy UK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>