DAYTON AUDIO WP8BT IP55 Indoor-Outdoor Pendant Speaker User Manual

June 3, 2024
DAYTON AUDIO

DAYTON AUDIO WP8BT IP55 Indoor-Outdoor Pendant Speaker

DAYTON-AUDIO-WP8BT-IP55-Indoor-Outdoor-Pendant-Speaker-User-Manual-
product

Thank you for purchasing the Dayton Audio ® 8” pendant speaker.This rugged, all-purpose speaker is designed to deliver reliable, high-quality audio in commercial and residential applications, while withstanding outdoor environments. The WP8 features an IP55 weath-er-resistant ABS construction, 2-way coaxial speaker design.

  •  8″ woofer with coaxial 1″ tweeter
  •  Integral 70V/100V transformer with selectable taps and 8 ohm bypass
  •  Suitable for indoor or outdoor installation
  •  Available in black or white finish

Please read these instructions completely before you begin your installation.

Speaker Connection

Remove about 8″ of the cable jacket to expose the inner conductors. Strip 1/4″ of in-sulation from each conductor and connect to the speaker terminals. When connect-ing the wires to the speakers, be sure to observe proper polarity for the best sound. Most CL2 rated speaker cable will have red and black colored wires inside the jacket. Connect the red wire to the (+) terminal and the black wire to the (-) terminal. The red (+) and black (-) speakers wires should correspond to the same terminals on the amplifier.

NOTE: If this speaker will be used with a 70V/100V distributed audio system, do not set the 70V/100V tap to the 8 ohm setting. Doing so may damage your speaker when playing. To use this speaker with a conventional (non- 70V/100V) audio sys-tem, change tap to the 8 ohm setting. If you are unsure what type of audio system you have, consult a professional installer before continuing.

Step 1:
Remove the speaker end cap
Using a screwdriver or other flat-blade tool, turn the tap selector knob to the desired setting. Selecting the 8 ohm setting will remove the transformer from the signal path and allow a conventional amplifier to drive the speaker. If using a 70V/100V system choose the appropriate output setting for the application.

Step 2:
Reinstall speaker end cap
Once you have selected the correct setting and mounting bracket you can feed the speaker wire through the end cap and reinstall.

Choose Speaker Location

If you will be installing your speaker outdoors, select a location that is protected from rain, snow, and out of direct sunlight for extended product life.
CAUTION:
Be certain that there are no electrical wires, water pipes, or heating ducts in the planned installation area before you begin drilling. If there is an electri-cal outlet nearby, turn off the circuit breaker to avoid possible injury.
NOTE:
Your Dayton Audio WP8 speaker is compact, but substantial in weight. Speaker should be mounted to a solid structure, not drywall. If drywall mounting is required, use high-strength anchors designed for heavy loads such as light fixtures. To avoid personal injury, please make sure the location you choose for mounting your speakers can safely support their weight.

Troubleshooting

Should your speakers not work properly, check the following:No sound from speaker or quiet/strange sound:

  •  Make certain you observed proper polarity for speaker inputs. Check the con-nections at the back of the receiver, and then at the speaker.
  •  Verify that the amplifier is powered on and the volume is turned up.
  •  Check that the correct transformer tap is selected for your application. If you are using a stereo amplifier or a receiver, use the 8 ohm tap.
  •  Mute feature or protection mode is activated. Check for short circuits in speak-er wiring.

Amplifier/Receiver cuts out:

  • This could be caused by a short circuit between the positive and negative leads. Check the connections at the back of the receiver, and then at the speaker; make sure that no strands of wire from one connector are touching the other connector.

Specifications

  • Model number:…………………….. WP8BT/WP8WT
  • Description:…………………………. Commercial indoor/outdoor speaker
  • Woofer:……………………………….. 8″ mineral-filled polypropylene
  • Tweeter:………………………………. 1″ fabric
  • Frequency response:…………….. 50-20,000 Hz
  • Impedance:………………………….. 8 ohms/70V/100V
  • 70V/100V taps:…………………….. 8 ohms/3.75W, 7.5W, 15W, 30W, 60W
  • Power handling (RMS/Peak):…. 75W/150W
  • SPL:……………………………………. 89.5 dB @ 8 ohm setting, 2.83V/1m
  • Dimensions:…………………………. 12-1/4″ height, 9-1/8″ diameter
  • Color:………………………………….. Black or white available
  • Weight:……………………………….. 9.2 lbs
  • Ingress protection rating:……….. IP55

5-Year Limited Warranty
See daytonaudio.com for details daytonaudio.com
tel + 937.743.8248 info@daytonaudio.com 705 Pleasant Valley Dr. Springboro, OH 45066 USA

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DAYTON AUDIO User Manuals

Related Manuals