Contour Design RollerMouse Pro Mouse User Guide

June 12, 2024
contour design

Contour Design RollerMouse Pro Mouse User Guide
Contour Design RollerMouse Pro Mouse

What’s in the Box?

  1. RollerMouse Pro
  2. Wrist rest
  3. Keyboard Risers
  4. USB charging cable (mounted)

What’s in the Box
What’s in the Box

User guide
What’s in the Box

Functions

A. Cursor speed
B. Power switch (no function for wired unit)
C. Rollerbar
D. Copy
E. Paste
F. Left-click
G. Right-click
H. Scroll wheel
I. Double-click

Functions Instructions
Functions Instructions

Connection

Connect the USB cable from your RolerMouse into an available USB port on your computer. Your computer will recognize your new device and connect automatically.

Cursor Speed (DPI)

Press the Cursor speed (button A) to cycle through cursor speeds. There are speed selections which range from slow (600 DPI) to fast (2800 DPI). Speed can be identified by the LED lights as shown. Hold Cursor speed (button A) for 8 seconds to default settings.
Cursor Speed

600 800 1000 1200 1400
1600 1800 2000 2400 2800

Rollerbar click force adjustment

Click force refers to the level of resistance when clicking the Rollerbar. To adjust click force, press and hold both button A (Cursor speed) and button F (Left-click) for two seconds, the LED light will show the current click force setting. While continuing to hold button A, release button F and use button H (Scroll wheel) to change click force settings. Release button A to select click force.

To disable the Rollerbar click function, adjust the click tension until all LEDs are illuminated.

Rollerbar click volume adjustment

The Rollerbar has 6 different click volume settings. To change the click volume, press and hold button A (Cursor speed) and button G (Right-click) for two seconds, the LED light will show the current click volume setting. To adjust click volume continue to hold button A and release button G, then move button H (Scroll wheel) up/down to adjust the click volumen. Release button A to confirm.

To disable the Rollerbar click volume, adjust the click volume until alle LEDs are illuminated.

Keyboard risers
Before using your RollerMouse Pro, please take a moment to adjust your keyboard.

If you are using other keyboards than Contour’s Balance Keyboard, you can use the Keyboard risers to achieve the desired keyboard height and angle. Simply place the Keyboard risers under your keyboards feet – as the keyboard was lying on the table.

For a proper ergonomic position the front edge of the the keyboard should be as close to the Rollerbar as possible. We recommend to use negative tilt helping you to hold a neutral wrist position and decreasing the extension of your fingers.

  • Negative tilt
    Negative tilt

  • Neutral flat
    Neutral flat

  • Neutral elevated
    Neutral elevated

  • Postive tilt
    Postive tilt

Software driver
All Contour’s ergonomic products are plug-and-play. If you want to customize your RollerMouse Pro, we recommend to download the free driver available at: contourdesign.com/drivers
Software driver

FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

IC Statement
This device complies with Industry Canada’s licenceexempt RSSs. Operation is subject to the following two conditions:

  1. This device may not cause interference; and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

The term “IC:“ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.

Warranty

If there is a functional defect due to faulty manufacturing, we will replace the product. This warranty does not cover damage that results from misuse of the product.

Attention!
If you attempt to dismantle your “RollerMouse Pro” you will invalidate your warranty

Contour

Contour Design Nordic A/S
Nyropsgade 41-43, 1. floor
DK-1602 Copenhagen V, Denmark

Phone: +45 70 27 02 27
Email: info@contourdesign.com

Contour Design, Inc. 10 Industrial Drive
Windham, New Hampshire 03087, USA

Phone: 603-893-4556
Email: ergoinfo@contourdesign.com

For more information please visit: www.contourdesign.com

Tested to comply with FCC and IC standards.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

contour design User Manuals

Related Manuals