Sunco ODS_2H_BBT-WH-6500K Outdoor LED Emergency Light User Manual

Sunco ODS_2H_BBT-WH-6500K Outdoor LED Emergency Light

Product Information

Specifications

• Voltage: 120V-277V
• Wattage: 2.4W
• Power Factor: 0.48
• CRI: 80
• Weight: 2.09 lbs
• Housing Material: ABS+PC
• Dimmable: N/A
• Beam Angle: 6 degrees
• Lumens: 120
• IP Rating: IP65
• Battery: 3.6V2000mAh Ni-Cad Battery
• Power Source: 120V/0.025A, 277V/0.01A
• Amps: 1 Year Warranty

Product Usage Instructions

Before You Start

Safety Information: Before proceeding, consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.

WARNING: Cancer & Reproductive Harm- www.P65Warnings.ca.gov

Installation Guide

1. STEP 1: Unscrew the two screws on the side of the lamp cover using a Phillips screwdriver.
2. STEP 2: Use a flathead screwdriver to open the lamp cover by prying it along a notch on the side.

Common Troubleshooting
If you encounter any issues with the product, refer to the troubleshooting section in the user manual. If you need further assistance, feel free to contact our support team for help.

FAQ

Q: How long should I let the battery charge before normal operation?
A: After electricity is hooked up to the unit, let the battery charge for at least 24 hours before normal operation.

User Manual
Outdoor LED Emergency Light
SKU:ODS_2H_BBT-WH-6500K
support@sunco.com 844-334-9938

Whats in the Box?

Components

What You Need

Get Your Gear

IMPORTANT: Prior to fixture installation, install junction box in ceiling or wall. When re-lamping, use only lamps specified in the fixture. Using other lamp types may result in transformer damage or unsafe conditions. The battery in this unit may not be fully charged upon unboxing. After electricity is hooked up to the unit, let the battery charge for at least 24 hours. It is then ready for normal operation. Unused wires must be capped with a wire nut.

Before You Start

Safety Information

• Turn off circuit breaker before installing this fixture.
• Suitable for use in damp environments at temperatures ranging from 32°F to 104°F. Not for use where directly exposed to water.
• Not compatible with photo controls.
• Not compatible with occupancy sensors.
• Not compatible with 3rd party sensors.
• Not compatible with dimmers.
• Not compatible with timing devices.
• All electrical connections must be in accordance with local and National Electric Code (N.E.C.) standards.
• Please review installation manual carefully before proceeding. Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.

WARNING:
Cancer & Reproductive Harm- www.P65Warnings.ca.gov

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation. Please review all instructions carefully prior to installation.

Dimensions

Installation Guide

• STEP 1
  Using a Phillips screwdriver (not included) to unscrew the two screws on the side of the lamp cover.

• STEP 2
  Insert a flathead screwdriver (not included) along a notch on the side of the lamp cover to prise open the lamp cover. Repeat on the opposite side to unlatch the lamp cover.

• STEP 3
  Using a screwdriver, press against the lamp’s buckle, and using the other hand, hold and lift the unit up while the buckle is pressed in. Continue holding the unit to keep the buckle open and then press open the other buckle in the same way. Remove the unit from the housing.

• STEP 4
  Drill a hole on the back of the housing and attach the EVA insulation to the back plate, then pull the input wires out. Mount the housing onto the junction box and secure with screws.

• STEP 5
  Connect wires through the -box, (1) When using 120V AC, connect the black wire to the building utility. (2) if using 277V AC, connect the red wire to the building utility. Connect neutral wires to the white lead. Unused wires must be capped using enclosed wire nuts. (For detailed wiring diagrams, please refer to page 7)

• STEP 6
  Connect the battery only after continuous AC power can be provided to the unit.

• STEP 7
  Place the unit back into the housing. Replace the lamp cover and screw back onto the housing.

• STEP 8
  Press the “TEST” button to check for proper operation of the unit.

Product Details

Wiring Diagram

Specifications

Common Troubleshooting

Feeling in the dark about an issue with your product? No worries! Our troubleshooting section is here to shed some light and provide you with easy- to-follow solutions for any problem. If you still need some assistance, please feel free to contact us with any questions. Our team of lighting experts are happy to help brighten your day.

Customer Support

Warranty Policy

This product is covered by our industry leading 1 year warranty.
It gets even better – scan the QR code for 2 extra years of protection!

30 Day Return Policy

• At Sunco, we value our customers and stand by the quality and performance of our products.
• If you are not completely satisfied with your purchase, we accept returns within 30 days of your purchase date.

Customer Service
Our Los Angeles team of lighting experts is here to assist you with all your needs! Contact us at:

Email: support@sunco.com
Call or Text: 844-334-9938

support@sunco.com 844-334-9938

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>