IKEA MITTZON Desk Sit Stand Desk Electric User Guide

IKEA MITTZON Desk Sit Stand Desk Electric

USER GUIDE

An electro-mechanical height-adjustable work surface with a control interface to adjust the height up and down. This product can be used by children aged from 14 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved by a person responsible for their safety.

Children shall not play with the product. Cleaning and user maintenance shall not be carried out by children without supervision.

Translated from the original instructions.

Advice and instructions for MITTZON sit/stand desk.

This product shall only be used together with the included power supply unit.

Every person who is responsible for this table at installation or employment of the table in daily use or in service and repair work should carefully read these instructions. Keep these instructions close to your sit/stand table.

Installation instructions

The table is assembled according to separate assembly instructions. Connect one side of the 90-degree connection cable (50mm long) to the M1 port
on the control box, then connect the other side to the cable from the leg. Connect the cable from the other leg to the M2 port on the control box. Connect the hand controller to the HS port and the power supply to the AC port on the control box. The control box should be placed in the tray created by the frame, and the electrical cable should be placed in the felt tray on the back. Position the electrical cable so it does not get damaged. Please check the assembly instructions. Connect the electrical cable to a wall socket (or a socket placed in the felt tray).

Note! The electrical cable must have full mobility.

The table is now ready for use. The motors will stop automatically when the table reaches its lowest or highest position respectively.

Usage of the table

The table shall only be used as a working table with the possibility to continuously adjust the working height between sitting and standing positions. The table shall only be used indoors and in dry premises (office environment or similar).

The table must not be overloaded – maximum load is 80 kg/176 lbs.
The motors may be run continuously for a maximum of 2 minutes. Afterwards, the motors must rest for approx. 18 minutes. before they can be used again.

Follow these instructions when adjusting table height:

1. Make sure all cables are connected firmly in place.
2. Make sure no objects are in the way of the table so that the height can adjust freely.
3. Press the up/down buttons on the hand controller to adjust the desk height.

Safety regulations

When the table moves up/down, keep the necessary safety distance to avoid the risk of entrapment between the moving table top and fixed objects in the surrounding area. When the table moves up/down, the user shall keep watch so that nobody is injured or no object is damaged. The table top must not be blocked by a fixed object which may risk that the table overturns. Always remove any office chair before the table moves up/down. The table tripod must not be altered or reconstructed in any way. In service and repair work of the table, the electrical cable must always be disconnected from the wall socket (the connected socket). Alterations to the control box and hand controller are absolutely forbidden! Alterations to the legs are absolutely forbidden! The table must not be used as a hoisting device for persons.

Maintenance and repair instructions

After approx. 1 week of use, check that the screws are properly tightened. If the table cannot be lowered or raised, check the connections between the desk power plug and the wall socket (the socket) and ensure that all cables are connected firmly in place. If any part of the electrical height-adjustable table needs to be replaced, the electrical cable must be first disconnected from the wall socket (the socket). After finishing the replacement, then connect the electrical cable to the wall socket (the socket) and then finish the reset process according to the reset instructions. After resetting successfully without any problems, the table is ready for use. If the table still does not work, please contact your nearest IKEA store or customer service.

Product servicing

Do not attempt to repair this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks.
Manufacturer: IKEA of Sweden AB
Address: Box 702, SE-343 81 Älmhult, SWEDEN
Telephone no.: +46(0)476-648500

SAVE THESE INSTRUCTIONS

The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or landfills and minimise any potential negative impact on human health and the environment. For more information, please contact your IKEA store.

EU Declaration of Conformity is included in the packaging as a separate document.

Handset operation instructions:

Collision detection

The system is designed to avoid possible damages to equipment due to collision. When the desk detects a sudden change in resistance, it will stop the movement and move in the reverse direction by approximately 30 mm-50 mm (depends on the movement speed, collision force and the load during collision).

Troubleshooting MITTZON

2. Unplug the desk from the wall socket for approximately one minute and reconnect.| 2. Follow the instructions to perform a reset. If the problem remains, contact !KEA customer service.
Only one leg is moving. Orange light blinks.| 1. Make sure that all cables are undamaged and connected firmly in place.| 1. Reconnect all the cables.
2. Unplug the desk from the wall socket for approximately one minute and reconnect| 2.Follow the instructions to perform a reset  If the problem remains, contact !KEAcustomer service.
The table stops and reverses during operation.| 1. Make sure that the table is not overloaded. (Max load 80 kg/176 lbs)| Remove the heavy things from the desk.
2. Make sure that nothing is blocking the table.| Remove the obstacle. Follow the instructions to perform a reset.
3. Check that the electrical cable has full movement when the desk is in its highest position and has reasonable slack| If the electrical cable is trapped, release it. Make sure it has enough length when the desk is in its highest position.
The table has stopped working.
Burning smell from short-circuit/ motor/power supply/control units.| Unplug the desk from the wall.| Identify the burned parts, then contact IKEAcustomer service.
Abnormal noise from table leg.| Check that the sound is normal or abnormal when you move the desktop up and down.| Follow the instructions to perform a reset. If problem remains, identify the defective parts andcontact IKEA customer service.
One segment of the 3-segment leg does not move.| I| Follow the instructions to perform a reset. If problem remains, identify the defective leg and contact IKEA customer service.
Overheat protection status.| I| This is not an error status, but due to the motor working continuously, overheat protection may activate. After approx.18 minutes of rest, the blue light will turn off and normal operation can be resumed.

Specifications:

• Model: MITTZON

• Input: AC 110V or 230V, 50/60Hz

• Sound Level: Lower than 50 dB(A)

• Standby Power Consumption: [Specify the value]

• Height Setting Interval: [Specify the range]

• Maximum Load: [Specify the maximum weight capacity]

• Temperature Interval at Usage: [Specify the recommended
  temperature range for usage]

• Temperature Interval at Storage: [Specify the recommended
  temperature range for storage]

• Humidity: [Specify the recommended humidity level]

• Power Supply Unit: [Specify details about the power supply
  unit]

Frequently Asked Questions (FAQ):

Q: What is the maximum load capacity of the MITTZON sit/stand desk?

A: The maximum load capacity is [specify the weight limit].
Exceeding this limit may damage the desk.

Q: Can I use the desk on carpeted floors?

A: It is recommended to use the desk on a flat, hard surface for stability and safety reasons.

© Inter IKEA Systems B.V. 2023

Documents / Resources

| IKEA MITTZON Desk Sit Stand Desk Electric [pdf] User Guide
MITTZON, MITTZON Desk Sit Stand Desk Electric, MITTZON Desk Sit Stand Desk Electric, Desk Sit Stand Desk Electric, Sit Stand Desk Electric, Stand Desk Electric, Desk Electric, Electric
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>