SUNCO LIGHTING 240W LED Alh Area Light Instruction Manual

SUNCO LIGHTING 240W LED Alh Area Light

Introduction

WARNING

To reduce the risk of electrical shock, fire, or injury to persons; read and follow all warnings and installation instructions before installing. All installation should be performed by a qualified electrician.

Rick of Electrical Shock Ensure power is off before installation or inspection. All wirings are performed in accordance with Electrical Code and local electrical code.

Risk of Fire

Fixtures are rated for use in 120-277V, 50-60Hz protected circuit and 90°Crated supply wire.

FOR YOUR SAFETY

Gloves and safety glasses should be worn while performing the installation.

Any alteration or modification of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/ or product malfunction.

To prevent product malfunction and/or electrical shock, this product must be properly grounded. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects

Do not alter, relocate, or remove wiring, lamp holders, power supply, or any other electrical component.

SUITABLE FOR WET LOCATIONS.

INSTALLATION

Disconnect the power before installation. Exploded view of completed assembly with component call out. 1,2,3,etc.

INSIDE THE BOX

Photocell Quick-install

• Remove Shorting Cap
  

• Install Photocell
  

Square & Round Pole Mount

Step1: Unscrew the screws of the iron bar with a screwdriver, adjust the hole spacing of the iron bar in advance according to the hole position on the Square or Round Pole. Remove the junction box cover of the Pole Mount bracket.

Step2: Fix the iron bar to the inside of the light pole with screws (Note: the screw is only screwed into 1/3 of its length), and lead out the input wire.

Step3: Pass the rubber gasket and the Pole Mount bracket through the screw and input wire on the light pole. Tighten the screw and then lock the other screw.

Step4: Run the fixture’s AC input wire through the bracket. Hang the fixture on the bracket, and tighten the screws.

Step 5: Pull the fixture’s input wire through the wiring hole into the pole and connect the wires inside or pull the wires out from the access panel on the extrusion arm bracket to connect the wires. Close the pole’s top cover or extrusion arm bracket panel.

Slip Fitter Mount

Step 1: Disassemble the Slip Fitter with a wrench.

Step 2: Run the fixture’s AC input wire through the base, then tighten screws to attach the base to the fixture housing.

Step 3: Run the fixture’s input wire through the lamp holder and lock it.

Step 4: Loosen the 4 locking bolts on the Slip Fitter with a wrench.

Step 5: Connect the fixture’s AC input wire to pole-wire with connectors, L to L(black), N to N(White), G to G(Green); If need to connect dimming wires, please also use the connector to connect “Dim+”(purple)to “Dim +”(purple), “Dim-“(gray) to “Dim-“(gray).

Step 6: Tighten the 4 locking bolts.

Step 7: Loosen the locking bolt on the Slip Fitter with a wrench to adjust the fixture mounting angle, then tighten the locking bolts. Adjustable angle range ± 9.

Wall Mount

Step 1: Unscrew the screws of the front cover and remove the front cover.

Step 2: Install the back housing directly to the wall using the wall anchor holes and appropriate screws.

Step 3: Connect the front case set to the back housing and tighten the screws. Hang the fixture on the Wall Mount bracket and tighten screws.

Step 4: Complete wiring in the wall mount bracket, close the front cover and tighten the 2 screws in the front case.

Trunnion Mount

Step 1: Loosen the screws on both sides of the bracket with a wrench, adjust Trunnion Mount bracket’s angle to keep parallel with its installation surface.

Step 2: Mark the fixing holes locations on the wall with Trunnion Mount bracket, then drill the hole in 10mm diameter with an electric drill.

Step 3: Knock the two expansion bolts (not included) into wall with a hammer.

Step 4: Install the Trunnion Mount bracket to the wall with expansion screw by tightening the nut with a wrench. Connecting fixture AC input wire to L N G, then make waterproof processing to joints, put wires into junction box.

Note: The adjustable angel range is 0-180°.

Universal Bracket Mount

Step 1:

Unscrew the screws, remove the iron bar, open the junction box cover.

Step 2: Run the fixture’s AC input wire through the base, then tighten screws to attach the base to the fixture housing.

Square & Round Pole Mount 

Step 3: Put the iron bar inside of pole, fix it with a screw, but reserve gaps of 32mm, pass the Pole Mount bracket through the screw and hang it on the screw, tighten this screw, pass the 2nd screw through the holes of Pole Mount bracket, pole and iron bar, then tighten it with a wrench.

Note: When installing on a round pole, please remove the rubber gasket.

Step 4: Loosen the locking bolt on the Slip Fitter with a wrench to adjust the fixture mounting angle, then tighten the locking bolts. Adjustable angle range ± 90°.

Step 5: Pull the fixture’s input wire through the wiring hole into the pole and connect the wires inside or pull the wires out from the access panel on the extrusion arm bracket to connect the wires. Close the pole’s top cover or extrusion arm bracket panel.

Slip Fitter Mount

Step 1:

Unscrew the screws, remove the iron bar, open the junction box cover.

Step 2: Run the fixture’s AC input wire through the base, then tighten screws to attach the base to the fixture housing.

Step 3: Run the fixture’s input wire through the lamp holder and lock it.

Step 4: Connect the fixture’s AC input wire to pole-wire with connectors, L to L(black), N to N(White), G to G(Green); If need to connect dimming wires, please also use the connector to connect “Dim+”(purple)to “Dim +”(purple), “Dim-“(gray)to “Dim-“(gray).

Step 5: Tighten the 4 locking bolts. Loosen the locking bolt on the Slip Fitter with a wrench to adjust the fixture mounting angle, then tighten the locking bolts. Adjustable angle range ± 90°.

Adjustable Square & Round Pole Mount

Step 1:

Disassemble the Slip Fitter with a wrench.

Unscrew the screws, remove the iron bar, open the junction box cover.

Step 2: Run the fixture’s AC input wire through the base, then tighten screws to attach the base to the fixture housing.

Step 3: Adjust the hole spacing of the iron bar in advance according to the hole position on the Square or Round Pole. Fix the iron bar to the inside of the light pole with screws (Note: the screw is only screwed into 1/3 of its length), and lead out the input wire.

Step 4: Pass the Pole Mount bracket through the screw and hang it on the screw, tighten this screw, pass the 2nd screw through the holes of Pole Mount bracket, pole and iron bar, then tighten it with a wrench.

Note: When installing on a round pole, please remove the rubber gasket.

Step 5: Loosen the locking bolt on the Slip Fitter with a wrench to adjust the fixture mounting angle, then tighten the locking bolts. Adjustable angle range ± 90°.

Step 6: Pull the fixture’s input wire through the wiring hole into the pole and connect the wires inside or pull the wires out from the access panel on the extrusion arm bracket to connect the wires. Close the pole’s top cover or extrusion arm bracket panel.

TROUBLESHOOTING

1. Check that the line voltage at the fixture is correct. Refer to wiring directions.
2. Is the fixture grounded properly.

Wattage Selectable

Wiring Diagram

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>