Wanbo Davinci 1 Pro Projector Instruction Manual

Wanbo Davinci 1 Pro Projector

Product Information

Specifications

• Brand: Shenzhen Wanbo Technology Co., Ltd.
• Website: www.szwanbo.cn
• Product: Mobile Phone with the Same Screen

FAQ

• Q: How should I clean the projector?
• A: Before cleaning, ensure the power plug is unplugged. Avoid using volatile chemicals or rubber/vinyl products. Use a soft cloth or cleaning paper for glasses to clean the lens. Do not expose to high temperatures or use abrasive materials that may scratch the lens.

Important Safety Precautions

You are recommended to use the projector in a dark room to achieve the best effect.

1. Please don’t install in places that are directly blown by the cold and warm air of air-conditioning, water condensation or high temperature may lead to the failure of the machine.

2. Ensure adequate ventilation and vents are not blocked to prevent heat accumulation inside the machine.

3. Please prevent foreign matters such as nails or paper scraps from falling into the machine. Do not insert any metals such as iron wire or screwdriver into the machine.
   Please turn off the power immediately and turn to a professional technician to remove it if any foreign matters fall into the body.

4. Do not place any liquid on this machine to avoid the risk of electric leakage.

5. Please use soft packaging materials to move the projector, install a lens protection cover to protect the lens from scraping, in addition, keep the projector from violent vibration.

6. Areas near the exhaust will become hot during and after we use the projector, it may lead to scalding if we touch it with a hand.

7. Please don’t watch the lens directly when it’s on so as to protect our eyes from damage.

Note

• Don’t open the shell to prevent electric shock, Please turn to qualified professional maintenance personnel for the maintenance as there are no parts in the machine that users can repair themselves.
• Don’t expose the machine to rain or moisture to prevent a misfire or electric shock.
• The product is applicable to be used under a temperature of 0-35℃ for a safe side.

Projector Part Name and Function

• Please check whether the connection is correct according to the mark on the power cord.

Installation and Adjustment

Device Power-On and Power-Off

Power-On

• Method 1: Press the power button on the projector to start.
• Method 2: Point the remote control to the projector and press the power key to turn it on.

Power-Off

• Short press the power button or the “ ” key on the remote control, once the shutdown prompt box appears, short press the power button or the power key on the remote control again.

Adjusts Focal Length

• Focus Length: When the picture image is blurred (indicated as the right picture), adjust the lens focus through ” “ ” on the remote control to achieve the best definition.

Projector hanger installation steps

1. Remove the 4 pads
2. Adjust the hanger angle to align with the hole and then tighten screws
3. Fixed the hanger

Basic Parameters

Remote Control

Mobile Phone with the Same Screen
The following steps can help us to display the content of our mobile phone to a projection screen synchronously through wireless wifi, just enjoy a larger picture (Applicable for intelligent Android version only).
Equipment requirements: support devices above IOS6 and Android 5.3 Min.

Android Devices User Instruction

1. Ensure the Phone and Projector are under the same WIFI (For Android Only).
2. Open’Eshare” of the projector.
3. Choose the device with the same name as Eshare to complete the mirror.

Mobile Phone with the Same Screen
IOS Devices User Instruction

1. Ensure the Phone and Projector are under the same WIFI (For iOS Only).
2. Open the “Eshare” of the projector.
3. Open “AirPlay”/ “Mirror” of the Phone.
4. Choose the device with the same name as Eshare to complete the mirror.

Mobile Phone with the Same Screen
How to be with the same screen for iPhone under the status of No Wifi

1. If there is no WIFI, firstly open the 4G network of the iPhone, then open the WIFI hot spot in the “Settings” interface of the phone.
2. Collect the iPhone’s hotspot WIFI for the projector.
3. Open “Eshare”.
4. Open “Airplay” / “Screen Mirror”.
5. Find the projector and click.

Mobile Phone Projection

How to “push” contents to the projector
Note: The advantage of push is it does not affect the normal use of the mobile phone.

1. Ensure the Phone and Projector are under the same WIFI.

2. Open the video software of the mobile phone and find the TV push icon in the four corners (it’s usually on the top right or the bottom right) (Each APPs has a different push icon design).
   Note: Not all video software has a function of push.

3. Click this icon to push videos to the projector. At the same time, we can have other. operations on the phone, it will have no conflict.

Singal Source Setting

Enter Setting interface in the main screen and select an input source. Enter into/the HDMI signal channel, and Press “OK” ” to switch the input source.
Note
If you want to return to the previous layer, please press the return key;
If you want to return to the main interface, please press the main screen key.

U Disk Support Format

Video

| AVI,DAT,FLV,MKV,MOV,MPG,MPEG,MP4,RM,RMVB,SWF, 3GP,TS,VOB
Audio| AMR,FLAC,M4A,MP3,MP2,OGG,WAV

Note: Specific operation contents are subject to the actual situation due to irregular updates of the product system.

Projection Distance Reference

Note: Projection size and distance are calculated according to the projection ratio, which may have a deviation and is subject to the actual status.

Cleaning Method

Please make sure the power plug is unplugged before cleaning.
Do not use pesticides or other volatile chemicals on the projector or lens. Do not let rubber or vinyl products contact the projector for a long time, which will damage the coating and make it peel off.

Clean the Projector

1. Wipe with a soft, dry cotton cloth. If it’s dirtied seriously, we can wipe it with a soft cloth that is stuck with diluted neutral detergent, then dry it with a clean and dry cloth. Please pay more attention if used with a chemical fibre cloth.
2. Don’t use thinner, benzene or any other solvents to avoid quality reduction or coating peeling off etc.
3. A brush can be inserted into the front of the vacuum cleaner to remove dirt inside the vents. Please don’t use a vacuum cleaner with no connector, or clean with vents directly.
4. Please don’t scrape the machine with nails or any other hard objects to avoid scratches.

Lens Cleaning

1. Clean lens with the same method for camera lens: please use a professional blow dryer or cleaning paper for glasses, and ensure lenses are not scratched.

Inlet and Outlet Dust Cleaning

1. Dust in the inlet and outlet will prevent ventilation and increase the internal temperature, which will cause defects.
2. Disconnect the power line after turning off the projector.
3. Clean the exterior with an electric vacuum cleaner, please install the brush head adapter on the vacuum cleaner first. Kindly take note: don’t use a vacuum cleaner with no connector or brush.

Poisonous and Harmful Substance, Element Name and Content

• O: Content of the hazardous substance in all homogeneous materials of the component is under the limits of SJ/T11363-2006.
• X: Content of the hazardous substance exceeds the limit requirement specified by SJ/T11363-2006 in at least one homogeneous material of the component. The components labelled “X” ” have no substitutive due to global technology development limits. Circuit board assembly *: including printed circuit board and its components, electronic components, etc.
• The number in the logo represents the normal environmental service life of the product. (Battery Excluded)

Warranty Card

1. We offer “three guarantees ” for this product, One one-year warranty for nonartificial damage since purchase (subject to purchase record).
2. We will provide warranty service for any default caused by product technical reasons during the warranty period.
3. Following situations are out of the range of the guarantee:
   • Accessories out of the mainframe
   • Unauthorized disassembly and repair without our consent.
   • Damage caused by external force and other natural disasters.
4. Please fill out this card and contact your distributor when products have a quality problem
5. This warranty is limited to product maintenance during the warranty period, no other liability

After-Sale Service Card

• Customer Name:……………………… Purchase of Shop:…………………………………..
• Customer ID:……………………………. Customer Tel:……………………………………….
• Fault Description (Please describe in detail for quick maintenance):…………….

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, According to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Suppose this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. In that case, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Before using this product, please read this product manual carefully

Thank you for purchasing our products. For your safety and benefit, please read this product manual carefully before using it. If you fail to follow the product instructions or precautions and cause any personal injury, property or other losses, the company will not bear any responsibility.

• Shenzhen Wanbo Technology Co., Ltd. www.szwanbo.cn.

References

• Wanbo万播投影仪|探索光影的无限可能

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>