Wanbo WPB84 Mozart 1 Pro Android LCD Projector Instruction Manual

Wanbo WPB84 Mozart 1 Pro Android LCD Projector

Specifications:

• Brand: Shenzhen Wanbo Technology Co., Ltd.
• Website: www.szwanbo.cn
• Product: Mobile Phone with the Same Screen

Product Usage Instructions

How to be with the same screen for iPhone under status of No Wifi:

1. If there is no WIFI, open the 4G network on your iPhone and then enable the WIFI hotspot in the Settings.
2. Connect the projector to iPhone’s hotspot WIFI.
3. Open Eshare on your phone.
4. Open Airplay/Screen Mirror.
5. Find the projector and click to connect.

Mobile Phone Projection:
Note: Advantage of push is it does not affect normal use of the mobile phone.

1. Ensure both the Phone and Projector are connected to the same WIFI network.
2. Open a video software on your mobile phone and look for the TV push icon (usually located in the top right or bottom right corners).
3. Click the icon to push videos to the projector. You can continue using your phone without any conflicts.

Singal Source Setting:

1. Enter the Setting interface on the main screen and select input source.
2. Enter into AV/HDMI signal channel and press OK to switch input source.

Note: Use the return key to go back to the previous layer and the main screen key to return to the main interface.

Cleaning Method:

• Ensure the power plug is unplugged before cleaning.
• Avoid using pesticides or volatile chemicals on the projector or lens.
• Avoid prolonged contact of rubber or vinyl products with the projector as it may damage the coating.
• Use a cleaning paper for glasses to clean the lens without scratching it.

FAQ:

• Q: Can I use this projector with devices other than iPhones?
  A: Yes, you can use this projector with other mobile phones that support screen mirroring or casting functions. Ensure both devices are connected to the same WIFI network for seamless projection.

• Q: How do I adjust the projection size and distance?
  A: The projection size and distance can be adjusted using keystone correction settings on the projector. Refer to the user manual for specific instructions on adjusting these settings based on your preferences.

Wanbo Projector Mozart 1

Introduction Manual

• Before using this product, please read this product manual carefully
• Thank you for purchasing our products. For your safety and benefit, please read this product manual carefully before using. If you fail to follow the product instructions or precautions, and cause any personal injury, property or other losses, the company will not bear any responsibility.

Important Safety Precautions

You are recommended to use the projector in a dark room to achieve the best effect.

1. Please don’t install in places that directly blown by cold and warm air of air-conditioning, water condensation or high temperature may lead to failure to the machine.
2. Ensure adequate ventilation and vent are not blocked to prevent heat accumulation inside the machine.
3. Please prevent foreign matters such as nails or paper scraps from falling into the machine. Do not insert any metals such as iron wire or screwdriver into the machine. Please turn off the power immediately and turn to professional technician to remove it if any foreign matters fall into the body.
4. Do not place any liquid on this machine to avoid risk of electric leakage.
5. Please use soft packaging materials to move the projector, install lens protection cover to protect the lens from scraping, in addition, keep the projector from violent vibration.
6. Areas near the exhaust will become hot during and after we use the projector, it may lead to scald if we touch with hand.
7. Please don’t watch lens directly when it’s on so as to protect our eyes from damage.

Note:

• Don’t open the shell to prevent electric shock, Please turn to qualified professional maintenance personnel for the maintenance as there are no parts in the machine that users can repair themselves.
• Don’t expose the machine to rain or moisture so as to prevent misfire or electric shock.
• The product is applicable to be used under a temperature of 0-35℃ for a safe side.

Important Safety Precautions

Projector Part Name and Function

*Please check whether the connection is correct according to the mark on the power cord.

Installation and Adjustment

1. Device Power-On and Power-Off
   Power-On

2. Method 1: Press the power button on the projector to start.

3. Method 2: Point the remote control to the projector and press the power key to turn it on. Power-Off
   Short press the power button or the “ ” key on the remote control, once shutdown prompt box appears, short press the power button or the power key on the remote control again.

4. Adjusts Focal Length

Focus Length: When the picture image is blurred (indicated as the right picture), adjust the lens focus through on the remote control to achieve the best definition.

Projector hanger installation steps

Basic Parameters

Remote Control

Mobile Phone with the Same Screen

• The following steps can help us to display content of our mobile phone to projection screen synchronously through wireless wifi, just enjoy with a larger picture (Applicable for intelligent Android version only).
• Equipment requirements: support devices above IOS6 and Android 5.3 Min.

Android Devices User Instruction

1. Ensure the Phone and Projector are under the same WIFI (For Android Only).
2. Open“Eshare”of the projector.
3. Choose the device with the same name with Eshare to complete mirror.

Mobile Phone with the Same Screen

IOS Devices User Instruction

1. Ensure the Phone and Projector are under the same WIFI (For IOS Only).
2. Open“Eshare”of the projector.
3. Open “AirPlay”/ “Mirror”of the Phone.
4. Choose the device with the same name with Eshare to complete mirror.

U Disk Support Format

Note: Specific operation contents are subject to actual situation due to irregular update of the product system.

Mobile Phone with the Same Screen

How to be with the same screen for iPhone under status of No Wifi

1. If there has no WIFI, firstly open 4G network of iPhone, then open WIFI hot spot in the “Settings” interface of the phone.
2. Collect iPhone’s hot spot WIFI for the projector.
3. Open “Eshare”.
4. Open “Airplay” / “Screen Mirror”.
5. Find the projector and click.

Mobile Phone Projection

How to “push” contents to the projector

• Note : Advantage of push is it does not affect normal use of the mobile phone.

  1. Ensure the Phone and Projector are under the same WIFI.
  2. Open video software of the mobile phone and finds the TV push icon in the four corners (it’s usually on the top right or on the bottom right) (Each APPs have different push icon design).

• Note: Not all video software have function of push. 3. Click this icon to push videos to the projector. At the same time, we can have other. operations on the phone, it will have no conflict.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
• Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.
• The device has been evaluated to meet general RF exposure requirement.
• To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).

Projection Distance Reference

Projection size (under status of no keystone correction / Inch)| Screen length

• width (cm)| Lens ~ screen (m)
  ---|---|---
  55| 122 × 68| 1.49
  60| 133 × 74| 1.63
  70| 155 × 87| 1.9
  80| 177 × 100| 2.17
  90| 199 × 112| 2.44
  100| 221 × 125| 2.71
  110| 244 × 137| 2.98
  120| 266 × 149| 3.25

Note: Projection size and distance are calculated according to projection ratio, which may have a deviation and subject to actual status.

Singal Source Setting

Enter Setting interface in the main screen and select input source. Enter into AV/HDMI signal channel, Press “OK” ” to switch input source.

Note:

• If you want to return to the previous layer, please press the return key;
• If you want to return to the main interface, please press the main screen key.

Cleaning Method

• Please make sure the power plug is unplugged before cleaning.
• Do not use pesticides or other volatile chemicals on the projector or lens. Do not let rubber or vinyl products contacts the projector for a long time, which will damage the coating and make it peeled off.

Clean the Projector

1. Wipe with a soft, dry cotton cloth. If it’s dirtied seriously, we can wipe with soft cloth that stuck with diluted neutral detergent, then dry with a clean and dry cloth. Please pay more attention if used with chemical fiber cloth.
2. Don’t use thinner, benzene or any other solvents to avoid quality reduction or coating peeling off etc.
3. A brush can be inserted into the front of the vacuum cleaner to remove dirt inside the vents. Please don’t use vacuum cleaner with no connector, or clean with vents directly.
4. Please don’t scrape the machine with nails or any other hard objects so as to avoid scratches.

Lens Cleaning

Clean lens with the same method for camera lens: please use professional blow dryer or cleaning paper for glasses, ensure lens are not scratched.

Inlet and Outlet Dust Cleaning

1. Dust in the inlet and outlet will prevent ventilation and increase the internal temperature, which will cause defect.
2. Disconnect power line after turn off the projector.
3. Clean the exterior with an electric vacuum cleaner, please install brush head adapter on the vacuum cleaner first. Kindly take note: don’t use vacuum cleaner with no connector or brush.

Poisonous and Harmful Substance, Element Name and Content

Lead
（Pb）| Mercury（Hg）| Cadmium
（Cd）| Hexavalent chromium（Cr(VI)）| Polybro minated Biphenyls（PBB）| Polybro minated Diphenyl Ethers（PBDE）
Shell| O| O| O| O| O| O
Optical Machine| O| O| O| O| O| O
Circuit Board| O| O| O| O| O| O
Fan| O| O| O| O| O| O
Other Wires| X| O| O| O| O| O
Remote Control| O| O| O| O| O| O
Power Supply| O| O| O| O| O| O

• O: Content of the hazardous substance in all homogeneous materials of the component is under the limits of SJ/T11363-2006.
• X: Content of the hazardous substance exceeds the limit requirements specified by SJ/T11363-2006 in at least one homogeneous material of the component. The components labeled “X” ” have no substitutive due to global technology development limits. Circuit board assembly *: including printed circuit board and its components, electronic components, etc.

The number in the logo represents the normal environmental service life of the product. (Battery Excluded)

Warranty Card

1. We offer “three guarantees ” for this product, One year warranty for non- artificial damaged since purchasing (subject to purchase record).
2. We will provide warranty service for any default caused by product technical reasons during warranty period.
3. Following situations are out of the range of guarantee:
4. Accessories out of the mainframe
5. Unauthorized disassembly and repair without our consent.
6. Damage that caused by external force and other natural disasters.
7. Please fill this card and contact your distributor when products have quality problem
8. This warranty is limited to product maintenance during the warranty period, no other liability

Shenzhen Wanbo Technology Co., Ltd.
www.szwanbo.cn

References

• Wanbo万播投影仪|探索光影的无限可能

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>