Welding Industries Australia MC113-0 Stick TIG Welder Weldarc 200 DC Instruction Manual
- June 1, 2024
- Welding Industries Australia
Table of Contents
- Welding Industries Australia MC113-0 Stick TIG Welder Weldarc 200 DC
- Product Information
- Product Usage Instructions:
- SAFETY
- INTRODUCTION
- RECEIVING
- FEATURES
- SPECIFICATIONS
- CONTROLS
- INSTALLATION
- BASIC WELDING INFORMATION
- GENERAL MAINTENANCE
- TROUBLE SHOOTING CHART
- SERVICE INFORMATION
- ASSEMBLY & PARTS LIST – WELDARC 200DC POWER SOURCE
- AUSTRALIAN WARRANTY INFORMATION
- NEW ZEALAND WARRANTY INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Welding Industries Australia MC113-0 Stick TIG Welder Weldarc 200 DC
Stick/TIG Welder
Specifications :
- Model: MC113-0
- Serial Numbers: From M1132A*
- Manufacturer: Welding Industries Australia
- Division: A Division of ITW Australia Pty Ltd
- Contact: 1300 300 884 | info@welding.com.au
Product Information
The Stick/TIG Welder is designed for welding applications and is equipped with features to ensure safe and efficient operation. It is essential to follow the provided instructions for proper maintenance and usage of the equipment.
Product Usage Instructions:
-
Safe Practices:
Before operating the welder, familiarize yourself with the Safe Practices section in the manual to prevent any injuries due to misuse or improper welding applications. -
Eye Protection:
Always wear a helmet with safety goggles or glasses with side shields and appropriate filter lenses to protect your eyes from radiant energy and flying metal during welding, cutting, or chipping.
FAQ:
Q: What should I do if I encounter issues with the welding equipment?
A: Refer to the Troubleshooting Chart in the manual to identify and resolve
common issues. If problems persist, contact the manufacturer’s service
information provided in the manual for further assistance.
Stick/TIG Welder
OPERATORS MANUAL | MC113-0
- WELDING INDUSTRIES AUSTRALIA
- A Division of ITW Australia Pty Ltd ABN: 63 004 235 063 1300 300 884
- Email: info@welding.com.au
- welding.com.au
- WELDWELL NEW ZEALAND
- A Division of ITW New Zealand
- NZBN: 9 429 039 833 129
- GST NO: 080177186
- 0800 9353 9355
- Email: info@weldwell.co.nz
- weldwell.co.nz
READ FIRST
- The information contained in this manual is set out to enable you to properly maintain your new equipment and ensure that you obtain maximum operating efficiency.
- Please ensure that this information is kept in a safe place for ready reference when required at any future time.
- When ordering spare parts, please quote the model and serial number of the power source and part number of the item required. All relevant numbers are shown in lists contained in this manual. Failure to supply this information may result in unnecessary delays in supplying the correct parts.
SAFETY
Before this equipment is put into operation, please read the Safe Practices section of this manual. This will help to avoid possible injury due to misuse or improper welding applications.
PLASTIC HANDLES ON POWER SOURCE
- Please note that the handle fitted to the Weldarc 200DC inverter is intended for carrying the equipment by hand only.
- DO NOT use this handle for suspending or mounting the Weldarc in any other manner.
SAFE PRACTICES WHEN USING WELDING EQUIPMENT
These notes are provided in the interests of improving operator safety. They
should be considered only as a basic guide to Safe Working Habits. A full list
of Standards pertaining to industry is available from the Standards
Association of Australia, also various State Electricity Authorities,
Departments of Labour and Industry or Mines Department and other Local Health
or Safety Inspection Authorities may have additional requirements. Australian
Standard AS1674.2 provides a comprehensive guide to safe practices in welding.
Eye protection
NEVER LOOK AT AN ARC WITHOUT PROTECTION. Wear a helmet with safety goggles or
glasses with side shields underneath, with appropriate filter lenses protected
by clear cover lens. This is a MUST for welding, cutting, and chipping to
protect the eyes from radiant energy and flying metal. Replace the cover lens
when broken, pitted, or spattered.
Recommended Shade Filter Lens
Burn protection
- The welding arc is intense and visibly bright. Its radiation can damage eyes, penetrate light-weight clothing, reflect from lightcoloured surfaces, and burn the skin and eyes. Burns resulting from gas-shielded arcs resemble acute sunburn, but can be more severe and painful.
- Wear protective clothing – leather or heat resistant gloves, hat, and safety-toed boots. Button shirt collar and pocket flaps, and wear cuffless trousers to avoid entry of sparks and slag.
- Avoid oily or greasy clothing. A spark may ignite them. Hot metal such as electrode stubs and work pieces should never be handled without gloves.
- Ear plugs should be worn when welding in overhead positions or in a confined space. A hard hat should be worn when others are working overhead.
- Flammable hair preparations should not be used by persons intending to weld or cut.
Toxic Fumes
- Adequate ventilation with air is essential. Severe discomfort, illness or death can result from fumes, vapours, heat, or oxygen depletion that welding or cutting may produce. NEVER ventilate with oxygen.
- Lead, cadmium, zinc, mercury, and beryllium bearing and similar materials when welded or cut may produce harmful concentrations of toxic fumes. Adequate local exhaust ventilation must be used, or each person in the area as well as the operator must wear an air-supplied respirator. For beryllium, both must be used.
- Metals coated with or containing materials that emit fumes should not be heated unless coating is removed from the work surface, the area is well ventilated, or the operator wears an air-supplied respirator.
- Work in a confined space only while it is being ventilated and, if necessary, while wearing an air-supplied respirator.
- Vapours from chlorinated solvents can be decomposed by the heat of the arc (or flame) to form phosgene, a highly toxic gas, and lung and eye irritating products. The ultra-violet (radiant) energy of the arc can also decompose trichlorethylene and perchloroethylene vapours to form phosgene. Do not weld or cut where solvent vapours can be drawn into the welding or cutting atmosphere or where the radiant energy can penetrate to atmospheres containing even minute amounts of trichlorethylene or perchloroethylene.
Fire and Explosion Prevention
-
Be aware that flying sparks or falling slag can pass through cracks, along pipes, through windows or doors, and through wall or floor openings, out of sight of the operator. Sparks and slag can travel up to 10 metres from the arc.
-
Keep equipment clean and operable, free of oil, grease, and (in electrical parts) of metallic particles that can cause short circuits.
-
If combustibles are present in the work area, do NOT weld or cut. Move the work if practicable, to an area free of combustibles. Avoid paint spray rooms, dip tanks, storage areas, ventilators. If the work can not be moved, move combustibles at least 10 metres away out of reach of sparks and heat; or protect against ignition with suitable and snug-fitting fire-resistant covers or shields.
-
Walls touching combustibles on opposite sides should not be welded on or cut. Walls, ceilings, and floor near work should be protected by heat-resistant covers or shields.
-
A person acting as Fire Watcher must be standing by with suitable fire extinguishing equipment during and for some time after welding or cutting if;
- Combustibles (including building construction) are within 10 metres.
- Combustibles are further than 10 metres but can be ignited by sparks.
- Openings (concealed or visible) in floors or walls within 10 metres may expose combustibles to sparks.
- Combustibles adjacent to walls, ceilings, roofs, or metal partitions can be ignited by radiant or conducted heat.
-
After work is done, check that area is free of sparks, glowing embers, and flames.
-
A tank or drum which has contained combustibles can produce flammable vapours when heated. Such a container must never be welded on or cut, unless
it has first been cleaned as described in AS.1674.2. This includes a thorough steam or caustic cleaning (or a solvent or water washing, depending on the combustible’s solubility), followed by purging and inerting with nitrogen or carbon dioxide, and using protective equipment as recommended in AS.1674.2. Water-filling just below working level may substitute for inerting. -
Hollow castings or containers must be vented before welding or cutting. They can explode. Never weld or cut where the air may contain flammable dust, gas, or liquid vapours.
Shock Prevention
- Exposed conductors or other bare metal in the welding circuit, or ungrounded electrically alive equipment can fatally shock a person whose body becomes a conductor. Ensure that the equipment is correctly connected and earthed. If unsure have the equipment installed by a qualified electrician. On mobile or portable equipment, regularly inspect condition of trailing power leads and connecting plugs. Repair or replace damaged leads.
- Fully insulated electrode holders should be used. Do not use holders with protruding screws. Fully insulated lock-type connectors should be used to join welding cable lengths.
- Terminals and other exposed parts of electrical units should have insulated knobs or covers secured before operation.
INTRODUCTION
-
MMAW (Stick Welding)
- Manual Metal Arc Welding (MMAW) is a process where an arc is struck between a flux-coated consumable electrode and the work piece. The arc and the weld pool are both shielded by gases generated by the flux coating of the electrode.
- The Weldarc 200DC has been designed to be used with 2.0mm, 2.5mm, 3.2mm and 4.0mm diameter electrodes. The smaller electrodes are used when welding at lower currents, such as sheet metal applications. Increasing the electrode diameter permits higher welding currents to be selected.
- WIA supplies a wide range of mild steel and special purpose electrodes which cater for home workshop, rural, and industrial requirements. Some popular AUSTARC electrodes are listed below. The correctly selected AUSTARC electrode will influence the quality of the weld, and the stability
of the arc.
-
Austarc 12P, Classification E4313-A
A popular general purpose electrode used with ease in all positions, vertical up or down. The smooth forceful arc makes it an ideal electrode for all general mild steel applications. -
Austarc 13S, Classification E4313-A
A smooth running electrode with a soft arc, particularly suited to light sheetmetal and smooth mitre fillet welds. -
Austarc 16TC, Classification E4916-A
A low hydrogen electrode with good arc stability and out-of-position welding characteristics. This electrode is ideal for medium carbon steels, or steels of unknown analysis. -
Unicord 312, Classification ES312-16
A high tensile, chromium nickel electrode specially formulated for joining all alloy steels and irons, and for tool and die maintenance. -
Staincord 316L-016, Classification E316L-16
For quality all position stainless steel welding. Extra smooth running, high arc stability, easy re-strike, excellent slag removal and bead appearance. -
Staincord 309Mo-16, Classification E309LMo-16
For high quality all position stainless steel welding. This extra low carbon alloy is specifically indicated for AISI 309Mo type alloys, but is also ideal for joining mild/low alloy steel to a range of 300 and 400 series stainless steels. Features extra smooth running, high arc stability, easy re-strike, excellent slag removal and
bead appearance. -
GTAW (TIG Welding)
Gas Tungsten Arc Welding (GTAW) is a welding process where the arc is struck between a non-consumable tungsten electrode and the work piece. A ceramic nozzle surrounds the tungsten electrode and directs a flow of inert gas, usually Argon, over the electrode and the weld zone. If filler metal is required, it is hand fed into the welding arc. The DC current output of the Weldarc inverter is suitable for welding most ferrous and non-ferrous metals.
RECEIVING
Check the equipment received against the shipping invoice to make sure the shipment is complete and undamaged. If any damage has occurred in transit, please immediately notify your supplier.
The Weldarc inverter package contains;
- Weldarc Inverter Power Source
- Twist-lock Electrode Holder 4m
- Work Clamp 3m
- (This) Operating Manual
- TIG Torch Complete with 8m cable with twist-lock connection.
- TIG Consumable KIT
- Argon flow gauge regulator REG003
- Gas hose
FEATURES
-
Fan on Demand
The machine has Fan on Demand feature. The fan will only operate when the temperature rise requires cooling. The Fan will run during power up, and power down. -
Voltage Reduction Device (VRD)
Whenever the welding output of the Weldarc inverter is open circuit (i.e. not arcing), the voltage across the welding leads is reduced to a safe level. This provides an increased level of safety to the welding operator during operations such as changing the electrode.
The “VRD SAFE” indicator on the front panel is on to confirm the output is in the safe condition.
The term VRD refers to a “Voltage Reducing Device” which complies with AS1674.2 for Category “C” conditions.
The machine will be supplied with VRD enabled or disabled, depending on the end market. -
VRD Disabled
The open circuit output voltage is maximum Volts DC. The ‘VRD SAFE’ indicator on the front panel will only light up momentarily during power up. Machine is supplied with an orange tag on the supply lead advising VRD is disabled. -
VRD Enabled
When not welding the ‘VRD SAFE’ indicator on the front panel will come on and the output voltage will be reduced
to approximately 23V, which is below the required safe level of 35V DC. -
Change VRD Function
If the VRD function does not suit the application, the VRD can be enabled or disabled by an authorised WIA service agent. -
Power Factor Correction (PFC)
PFC provides an input power conditioner system to smooth the input current.
On a conventional inverter machine the input current presents in short high current pulses every half mains cycle. These pulses, cause input voltage drop, on extension leads and generators.
The PFC spreads the current pulse over the whole mains cycle.
The overall effect is PFC provides stable operation, on challenging power supplies, particularly on long supply leads & generators.
SPECIFICATIONS
Manufactured to Australian Standard AS60974-1 IEC60974-10 6.3.2 6.3.3.
Term Value
- Rated Input Voltage 220 – 240 V
- Power Frequency 50/60 Hz
- Rated Input Capacity 6 KVA
- Generator Capacity 6 kVA Peak
- Rated Maximum Supply Current Imax 25 A
- Maximum Effective Supply Current Ieff 14 A
- Output No Load Voltage 78 V
- Supply Main Circuit Breaker 30 A
- Supply Cable 2.5mm2 & Plug Rating 15 A
- Extension Lead Rating 15 A
- Open Circuit Voltage
- VRD Enabled: Uo = 14 V
- VRD Disabled: Uo = 78 V
- Rated Output @ 40°C
- Stick MMA 180 A @ 27.2 V 30% Duty
- 127 A @ 25 V 60% Duty
- 99 A @ 24 V 100% Duty
- TIG 200 A @ 18 Volts 30% Duty
- 141 A @ 15.6 V 60% Duty
- 110 A @ 14.4 Volts 100% Duty
- Current Up Slope Time 0 – 10 S
- Current Down slope Time 0 – 10 S
- Pulse Frequency 0.2 – 500 Hz
- Pulse Ratio Width Adjustment 5 – 95 %
- Arc Force Control MMA 0-100% of preset value
- Arc Start MMA 0-100%
- Post Gas Time 0.5 – 15 S
- Pre Gas Time 0 – 5 S
- Cooling Type Fan on Demand
- Efficiency ≥ 85% n
- Power Factor 0.99 Cos§
- Insulation Degree H
- Cover Protection Degree IP23S
- Weight 12kg
- Shipping Weight 23kg
- Dimension L × W × H 500 mm x 215 mm x 345 mm
- Shipping Dimension L × W × H 690 mm x 320 mm x 440 mm
CONTROLS
-
VRD Safe Mode Indicator
When the machine is in MMA stick mode the light will be on when the voltage across the output terminals is reduced to safe level. The VRD will operate in accordance the requirements of AS1674.2 Category C Environment. -
Over Temperature Indicator
This light will come on if any internal thermal protection devices have operated due to overheating, caused by the duty cycle being exceeded.
The machine will not weld but the fan will continue to operate to cool the machine. When a safe temperature has been reached, the thermal protection device will reset and welding can continue. -
Power On
This light will be on when the input supply is turned on. -
Latch Mode 2T/4T
Latch mode provides a 2 STEP or 4 STEP trigger control while in TIG mode: -
Step
In this mode the torch trigger must be pressed on to initiate welding and held on till welding is finished.
Up slope and down slope, ignition current and crater current cannot used in the 2 STEP. -
Step
In this mode the torch trigger switch is pressed to start the arc.
After PRE-GAS time the Arc will initiate. The current will stay at the ARC IGNITION setting.
When trigger is released the current will increase to the WELDING CURRENT setting, according to the UP SLOPE time.
Output will continue at WELDING CURRENT setting.
When torch trigger is pressed again then the weld output will decrease down to CRATER CURRENT setting, according to the DOWN SLOPE time.
Weld output will remain at CRATER CURRENT until torch trigger is released, then gas will flow for POST GAS time. -
Adjustment Knob
This knob is used to adjust welding parameters.
The knob primary function is to adjust the welding current. Turning the knob will adjust the weld current which is indicated on the digital display.
Press and release the knob, will select one of the additional welding parameters (see 10) The selected parameter indicator will be lit and then the parameter can be adjusted by turning the knob. The parameter indicator is held for about 4 seconds before reverting back to normal current adjustment mode. -
Weld Mode Selection
The Weld Mode can be selected between the two mode of operation. -
Stick MMA Mode
In this mode the machine performs as a DC stick MMA welding machine. The HOT START and ARC FORCE parameters can be adjusted on the front panel by pressing the Adjustment Knob then rotating to change. -
TIG Mode
In this mode the machine will perform as a DC TIG machine. -
TIG Start Mode
Use This mode to select between High Frequency (HF) start, or LIFT TIG start. -
High Frequency (HF) arc start is when the tungsten is near the work piece and the torch trigger is pressed, then a high energy spark is created to jump from the tungsten to work piece and initiate an Arc.
-
Lift TIG start the tungsten is touched to the work piece and lifted to then start the arc.
-
Pulse Mode
The machine can operate with: -
Flat DC output or
-
Output that Pulses between two DC currents. In Pulse TIG the parameters for adjusting the pulse shape will be available for adjustment.
Peak Current, Pulse Ratio, Frequency Hertz, and Base Current can be adjusted, refer to 10.5
Pulse mode can be used for thin plate welding, maintaining good penetration, but with reduced Heat Effected Zone. -
Amps Display
The digital display will show Amps while adjusting current with knob 5, and then display weld Amps while welding is in progress. -
Welding Parameters
Press Adjustment Knob (5) to access welding parameters. -
Pre Gas
Pre gas flow can be set to a maximum of 5 seconds, to allow gas flow before Arc Start. -
Ignition Current
While in 4 STEP latch mode the arc will start and maintain the Ignition current output until the trigger torch is released.
The IGNITION CURRENT is adjusted 0-100% of the WELD CURRENT setting. -
Up Slope
The UP SLOPE time is the time taken for the weld current to transition from the IGNITION CURRENT value to WELD CURRENT value. The time can be adjusted from 0 to 10 seconds. -
Welding Current
The setting for actual weld current. -
Pulse Welding
Pulse welding allows the current to be pulsed between two different values, the frequency and ratio can be adjusted. This feature can be used on thin material. -
Peak Current
Set the Peak current Amps when in pulse mode. -
Pulse Duty
Set the ratio in % for the peak current compared to the back ground current. Range is 5% to 95%. -
Hertz
The frequency of the pulse can be set, as number of pulses per second (Hertz) 0.2Hz to 500Hz. -
Base Current
Set the Base current Amps when in pulse mode. The Base Current can
be adjusted to 10 to 95% of the Peak Current. -
Down Slope
The DOWN SLOPE time is the time taken for the weld current to transition from the WELDING CURRENT value to CRATER CURRENT value. The time can be adjusted from 0 to 10 seconds. -
Crater Current
The current at the end of WELD can be adjusted to a value which will allow controlled finish of the weld. The end of weld pool (Crater) can be filled. -
Post Gas
The Post Gas time can be adjusted to allow gas to flow after weld has stopped. This feature can be used to provide a gas shield to the cooling weld pool. Adjustable from 0 to 15 seconds. -
Arc Force
When machine is in Stick MMA mode, selecting the ARC FORCE allows adjustment of the increase in current that will occur when the arc starts to short circuit, or snap out. Adjusting this value can be useful when using cellulose electrodes.
The amount of current is preset, the adjustment is a % of the preset value. -
Hot start
When machine is in Stick MMA mode, selecting HOT START allows adjustment of the increase in current that will occur at Arc Start HOT START is useful for getting arc established on a cold start. The amount of current is preset, the adjustment is a % of the preset value. -
Power On/Off Switch
In the OFF position, this switch isolates the power source from mains power supply. The switch is located on the rear panel. -
Remote Control Adjustment
The output current of the machine can be controlled remotely by On/ Off trigger switch control and current control adjustment, located in the torch hand piece, or in foot control.
The Remote control adjustment will allow minimum to 100% of the current setting on the machine.
For example if the machine is set to 150A the remote adjustment will adjust 10-150A. -
TIG torch used for remote control adjustment
The TIG torch will require a trigger switch and current control potentiometer in the hand piece.
Control plug of the TIG torch is connected to the machine remote control socket FIG 7.
Turn the machine on.
First the machine needs to be adjusted to maximum desired current.
To do this the remote control knob
on the TIG torch needs to be adjusted to maximum.
Adjust to the desired maximum current (such as 150A) on the machine with the control knob FIG 1 (5). The AMPs digital display will then show 150A.
Adjust the control knob on the TIG torch, the AMPS display will then change as the knob is adjusted. -
Foot Control for remote control adjustment
The WIA foot control (part number AA76) has an in built trigger switch and current control and can be used to control the weld start and weld current.
Control plug of the TIG torch is connected to the machine remote control socket FIG 7.
Turn the machine on.
First the machine needs to be adjusted to maximum desired current
Select LIFT TIG MODE to prevent HF during setup.
Press the foot control pedal to maximum.
Adjust to the desired maximum current (such as 150A) on the machine with the control knob FIG 1 (5). The AMPs digital display will then show 150A.
Release the foot control pedal and the current will adjust down from 150A to 10A.
HF MODE can now be selected if required.
INSTALLATION
-
Do Not Touch Live Electrical Parts
Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit is electrically live whenever the output is on. The input power circuit and machine internal circuits are also live when power is on. In semi-automatic wire welding, the wire, wire reel, drive roll housing, and all metal parts touching the welding wire are electrically live. Incorrectly installed or improperly grounded equipment is a hazard. Do not touch live electrical parts. ELECTRIC SHOCK can kill. Wear dry, hole-free insulating gloves and body protection. Insulate yourself from work and ground using dry insulating mats or covers big enough to prevent any physical contact with the work or ground. -
Connection to Electrical Mains Power Supply
- The Weldarc 200DC is fitted with a 15 Amp plug, recognisable by a wide earth pin. Power supply authorities require that equipment fitted with a 15 Amp plug shall ONLY be connected to a 240 Volt, 15 Amp power point. DO NOT modify the plug.
- The minimum capacity of the main power supply wiring and power outlet supplying a welder is selected according to the Effective Primary Current of the equipment. Refer to Section 4.
- The minimum recommended main power supply circuit breaker ratings for the Weldarc 200DC inverters are listed in Section 4.
- If it becomes necessary to replace the mains flexible supply cable, use only cable with correct current rating. See Section 4.
- If it is necessary to use an extension power supply cable, ensure that it is rated as per Section 4. Voltage drop which will occur over long lengths of cable will reduce the maximum welding current available from the equipment.
- This machine has PFC feature. If the mains voltage supply is low, the PFC will require more mains current to provide the necessary weld power. Therefore, low mains voltage or mains voltage drop will increase mains current.
-
Successful Operation
- Welding equipment at maximum output require high current during operation, then minimum current during idle time.
- Mains supply circuit breaker tripping can sometimes occur.
-
Successful operation will depend on a number of factors:
- Variation in circuit breaker thresholds.
- Ambient temperature.
- Number of previous circuit breaker operations.
- Actual weld conditions, resulting in higher weld currents.
- Repeated starts can result in repeated surge currents raising circuit breaker threshold.
-
Low supply voltage, resulting in higher supply current.
-
Repeated Circuit breaker operation at weld start can sometimes be overcome by using a “D” curve circuit breaker.
-
To reduce nuisance tripping, a higher rated circuit breaker can be selected, but the supply circuit wiring capacity must be increased to suit.
Connection to Generator
- The Weldarc 200DC can be operated from a generator. The PFC feature will allow greater tolerance to variable generator outputs. However, it is not recommended that the equipment be powered from small engine-driven generator sets unless they have adequate voltage regulation. Poor regulation results in peaks of supply voltage which can occur with some equipment of this type. Excessive voltage peaks can damage the circuits of the welder.
- Generators used to power this equipment must have the recommended minimum capacity and incorporate output voltage regulation.
- Due to variation between generators by different manufacturers, it is impossible for WIA to validate operation from all generators. Therefore, correct operation of welding equipment on the generator should be confirmed by the manufacturer, before purchasing the generator.
BASIC WELDING INFORMATION
Stick Welding (MMAW)
Connection for Stick Welding
It is important to select the electrode polarity in accordance with the
manufacturers recommendations for that electrode. Most common electrodes,
including cellulose types, are operated with the electrode at positive
polarity, as illustrated in Figure 6.
Stick Welding
-
Be certain that you are wearing suitable protective clothing, gloves etc and that you are working in a non-hazardous area. If necessary, refer again to Section 1 – Safe Practices in this manual.
-
Connect the work clamp to the work piece. Place the desired electrode in the electrode holder.
-
Turn on the power switch located on the rear panel. Wait approximately 5 seconds as the unit goes through its initiation sequence.
-
Use the Weld Mode Selection button to select Stick Mode.
-
Select an appropriate welding current for the electrode diameter by setting the knob on the machine front panel. WIA AUSTARC electrodes will give the best results.
-
To strike the arc, drag the end of the electrode along the work piece as if striking a match. As the arc initiates, lift the electrode slightly away, aiming to establish an arc length of approximately 3mm.
-
As the electrode end is consumed, feed the electrode into the arc in order to maintain arc length. As a general rule, the arc should be held as short as possible while still giving stable burn off and good weld appearance. An arc which is too long causes an unwieldy flow of metal with
a rough weld appearance and reduced penetration. An arc too short leads to a narrow weld deposit and “stuttery” arc characteristics, and the electrode is liable to freeze onto the work piece. -
As the solidified weld deposit forms, move the end of the electrode slowly along the weld path, aiming to maintain a pool of molten weld metal behind the arc. Decreasing this rate of travel will result in a wider weld deposit, and similarly increasing it will narrow the weld deposit.
-
Always fill the crater which tends to form at the end of a weld deposit, by pausing momentarily before withdrawing the electrode to break the arc. Unfilled craters are a point of weakness, and can lead to weld cracking.
Current Range for General Purpose Electrodes
Diameter (mm) | Current (Amps) |
---|---|
2.0 | 40 – 60 |
2.5 | 60 – 85 |
3.2 | 90 – 130 |
4.0 | 130 – 180 |
TIG Welding (GTAW)
-
Connection for TIG Welding
For TIG Welding, the TIG torch is connected to the negative terminal. Figure 7 illustrates the correct connection of the welding torch and gas supply. Welding grade Argon is the shielding gas most commonly used for DC GTAW welding. The torch will require a tungsten electrode.
Before first use of the welding torch, allow gas to purge the torch and hoses for 1 minutes at approximately 10 litres/min. For welding purposes, the gas flow rate should be set in the range 5-11 litres/min. -
Electrode TIG
Thoriated Tungsten electrodes are normally used for DC welding current. -
Tungsten Electrode Preparation
- The tungstens needs to be ground to a point, the grinding should only be in the direction of the point and should be done on a fine grit grinding wheel. The resulting grind pattern will produce a sharp directed arc. Poor tip preparation will result in arc wander.
- A common practice is to grind the tip such that the length of the points is approximately 2 times the diameter. The result will be an included angle of 30 degrees.
- It is important to maintain the electrode point for DC. If the tip accidently touches weld pool it will become contaminated and the arc will become erratic, and will need to be re ground.
- Tungstens containing at least 2% lanthana will hold a point when used for DC TIG.
Tungsten Current Ranges
Electrode Diameter (mm)| Gas Cup Size| DC Current
Amps| Filler Wire Diameter (mm)
---|---|---|---
1.0| 6| 15-80| 1.6
1.6| 6| 70-150| 1.6-2.4
2.4| 8| 150-250| 2.4-3.2
- Safety Consideration Thoritated Tungsten.
- Thoriated Tungsten contains the element Thorium (Th). Thorium is a radioactive element which mainly emits alpha particles. Alpha particles cannot penetrate skin, or clothing, but can be a harmful carcinogen if released inside the digestive tract, or lungs.
- There is almost no release of radioactive material during arcing.
- There is no significant hazard in handling and storage. The Thoria is inside the tungsten electrode, it is enclosed in a tungsten matrix and so there is little radiation emitted externally.
- The greatest risk of exposure is during the grinding of the thoriated tungsten electrodes. Care needs to be taken, to control the dust. A dust mask should be worn, and grinder area clean up should be done with a vacuum cleaner.
- TIG Welding Operation
- Connect the Work Clamp to the work piece.
- Turn on the power switch located on the rear panel. Wait approximately 5 seconds as the unit goes through its initiation sequence.
- Use the Weld Mode Selection Switch to select LIFT TIG or HF TIG Mode.
- Select an appropriate welding current for the job by setting the knob on the machine front panel.
- HF Start
- When HF Start TIG is selected then the electrode tip is bought close to the work piece, but not touching.
- Pressing the trigger will produce a high voltage spark that will jump to the work piece and initiate an arc.
- HF TIG can be used where work piece contamination by the electrode is a concern. Also where repetitive starts causes contamination of the electrode, which produces an unstable arc.
LIFT TIG Operation
When the Welding mode is set to LIFT TIG then the arc start can be achieved
with the following procedure.
-
Touch the electrode lightly against the work piece.
-
Press the torch trigger switch. The shielding gas will start to flow and a small current will pass through the electrode.
-
While still holding the electrode against the work piece, roll the hand piece over until the cup rests on the work piece.
Use the cup as a pivot point to roll the hand piece over allowing the electrode to lift of the work piece.
The arc will ignite. -
Immediately lift the cup of the work piece, the current will rise to the welding level within the up-slope time.
Use of a copper striking plate
can be used to avoid electrode contamination. The electrode can also be contaminated by contact with the filler rod. A contaminated electrode produces an unstable arc. If this occurs regrind the electrode tip.
GENERAL MAINTENANCE
Before removing the power source covers, ENSURE that the equipment is disconnected from the mains power supply. When the equipment is energised LETHAL VOLTAGES are present on the electrical components enclosed.
Dust
Care should be taken to prevent excessive build-up of dust and dirt within the
welding power source. It is recommended that at regular intervals, according
to the prevailing conditions, the equipment covers be removed and any
accumulated dust be removed by the use of a dry, low pressure compressed air,
or a vacuum cleaner. The machine should be blown out with compressed air at
least every 12 months as grinding dust can settle on PCB componentry causing
failure. Failure to maintain machines may void warranty.
EXTERNAL TROUBLE SHOOTING
- If you are in Australia and the following checks do not identify the fault condition, the equipment should be returned to a WIA Service agent. Phone 1300 300 884 for details of your nearest service agent.
- If you are in New Zealand and the following checks do not identify the fault condition, the equipment should be returned to the original place of purchase with proof of purchase, or contact Weldwell on 06 8341 600.
TROUBLE SHOOTING CHART
SERVICE INFORMATION
-
If the welding machine requires service or repair, take the machine to an authorized service agent.
- Australian service agents can be located on the welding.com.au website.
- Alternatively call customer service; Australian 1300 300 884
- New Zealand 0800 9353 9355
- When contacting a service agent please have an accurate description of the fault, and the machine serial number located on the base on the machine.
- M1132A……………………
-
CAUTION: The following information is intended for use by qualified service personnel. When the unit is energised LETHAL VOLTAGES are present on the electrical and electronic components. It is not intended that persons without suitable training and knowledge attempt to perform service tasks on the components of this welder.
-
Before removing the equipment cover, ENSURE that the equipment is disconnected from the mains power supply. When the equipment is energised LETHAL VOLTAGES are present on the electrical components enclosed.
If the supply cable is damaged it must be replaced by the manufacturer, their service agent or a similarly qualified person. -
IMPORTANT NOTICE: Warranty may be voided if equipment is powered from an unsuitable engine driven generator.
Generators used to power this equipment must have a minimum rated capacity as per Section 4
and incorporate output voltage regulation. Due to variation between generators by different manufacturers, it is impossible for WIA to validate operation from all generators. Therefore, we recommend that operation of equipment on the generator is received from the manufacturer before purchasing the generator. -
The electrical components of the equipment are shown in the circuit diagram below. The Weldarc inverter is an inverter type design, where the mains supply is first rectified, passed through a PFC boost circuit, filtered then chopped to a high frequency before being applied to the welding transformer. The output of this transformer is rectified to form the welding output of the machine.
CIRCUIT DIAGRAMS – POWER SOURCE
Fig 13 Weldarc 200 DC Circuit Diagram
ASSEMBLY & PARTS LIST – WELDARC 200DC POWER SOURCE
Fig 14 Weldarc
200 DC Power Source Assembly
WELDARC 200DC PARTS LIST
Item # | Part # | Description | Qty |
---|---|---|---|
1 | M0109 | Handle | 1 |
2 | PAN178 | Metal Cover | 1 |
3 | PWA098 | Emc Filter Board | 1 |
4 | PWA077 | IGBT Inverter Board | 1 |
5 | PWA078 | High Frequency Board | 1 |
6 | M0110 | Front Plastic Panel | 2 |
7 | PWA076 | Front Panel Control Pcb | 1 |
8 | M0104 | Potentiometer Knob | 1 |
9 | CX58 | Panel Mount Dinse Socket | 2 |
10 | M0094 | Argon Gas Connector M10 | 1 |
11 | E0079 | Socket 5 Pin | 1 |
12 | L0035 | Current Sensor | 1 |
13 | PWA060 | Rectifier Board | 1 |
14 | PWA079 | PFC Board | 1 |
15 | FAN021 | Fan | 1 |
16 | E0078 | Rocker Switch | 1 |
17 | N/A | Power Cable 2.5mm2 | 1 |
18 | E0100 | Gas Valve | 1 |
19 | REG003 | Argon Regulator | 1 |
20 | CLA002 | Work Clamp | 1 |
21 | TIG010 | TIG Torch | 1 |
ASSEMBLY AND PARTS LIST – TORCH
Part # | Description | Qty |
---|---|---|
10N31 | Collet Body 1.6mm | 1 |
10N32 | Collet Body 2.4mm | 1 |
10N28 | Collet Body 3.2mm | 1 |
10N23 | Collet 1.6mm | 1 |
10N24 | Collet 2.4mm | 1 |
10N25 | Collet 3.2mm | 1 |
10N50 | Ceramic Nozzle Size 4 (6mm) | 1 |
10N49 | Ceramic Nozzle Size 5 (8mm) | 1 |
10N48 | Ceramic Nozzle Size 6 (10mm) | 1 |
10N47 | Ceramic Nozzle Size 7 (11mm) | 1 |
10N46 | Ceramic Nozzle Size 8 (12.5mm) | 1 |
57Y04 | Short Back Cap | 1 |
57Y03 | Medium Back Cap | 1 |
57Y02 | Long Back Cap | 1 |
E0087 | Cable Plug | 1 |
M0131 | Snap Gas Connector | 1 |
AUSTRALIAN WARRANTY INFORMATION
WIA Weldmatic MIG & Weldarc MMA Equipment
3 Year Gold Shield Warranty Statement
- Effective 1st January 2022
- Welding Industries of Australia (WIA) warrants to the original retail purchaser that the Weldmatic welding machine purchased (Product) will be free from defects in materials and workmanship for a period of 3 years from the date of purchase of the Product by the customer. If a defect in material or workmanship becomes evident during that period, Welding
- Industries of Australia will, at its option, either:
- Repair the Product (or pay for the costs of repair of the Product); or
- Replace the Product.
- In the event of such a defect, the customer should return the product to the original place of purchase, with proof of purchase, or contact Welding Industries of Australia on 1300 300 884 to locate an authorised service agent.
- Products presented for repair may be replaced by refurbished products of the same type rather than being repaired. Refurbished parts may be used to repair the product.
- Replacement of the product or any part does not extend or restart the Warranty Term. The repair of your products may result in the loss of any user-generated data. Please ensure that you have made a copy of any data saved on your product.
- Any handling and transportation costs (and other expenses) incurred in claiming under this warranty are not covered by this warranty and will not be borne by Welding Industries of Australia.
- Welding Industries of Australia will return the replacement product, if original found to be faulty, freight free to the customer.
- This warranty covers the Weldarc power source only, and does not extend to
- the accessories included in the original purchase package.
- The obligation of Welding Industries of Australia under this warranty is limited to the circumstances set out above and is subject to:
- The customer being able to provide proof of purchase of the Product and the purchase price paid for the Product;
- The relevant defect in materials or workmanship;
- The Product not having been altered, tampered with or otherwise dealt with by any person in a manner other than as intended in respect of the relevant Product; and
- The Product not having been used or applied in a manner that is contrary to customary usage or application for the relevant Product or contrary to any stated instructions or specification of Welding Industries of Australia.
For products purchased in Australia
- Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits given by this warranty are in addition to other rights and remedies which may be available to the customer under any law in relation to goods and services to which this warranty relates.
- Warranty provided by:
- Welding Industries of Australia
- (ABN 63 004 235 063)
- A Division of ITW Australia Pty Ltd
- 5 Allan Street, Melrose Park
- South Australia 5039
- Ph: 1300 300 884
- Email: info@welding.com.au
- Web: www.welding.com.au
NEW ZEALAND WARRANTY INFORMATION
WIA Weldmatic MIG & Weldarc MMA Equipment
3 Year Gold Shield Warranty Statement
- Effective 1st January 2022
- In the event of defects listed in the Australian warranty conditions, the customer should return the Product to the original place of purchase, with proof of purchase, or contact Customer Service on 0800 9353 9355.
- The warranty shall not apply to parts that fail due to normal wear.
- For customers located in New Zealand, you can contact:
- Weldwell New Zealand
- Division of ITW New Zealand
- 59 Thames Street
- Napier 4110
- New Zealand
- Ph: 0800 9353 9355
- Email: info@weldwell.co.nz
- Web: www.weldwell.co.nz
WELDING INDUSTRIES AUSTRALIA
- A Division of ITW Australia Pty Ltd ABN: 63 004 235 063
- 1300 300 884
- Email: info@welding.com.au welding.com.au
WELDWELL NEW ZEALAND
- A Division of ITW New Zealand NZBN: 9 429 039 833 129 GST NO: 080 177 186
- 0800 9353 9355
- Email: info@weldwell.co.nz
- weldwell.co.nz
References
- Innovative welding products & solutions for NZ, Australia & South Pacific | Weldwell NZ
- Innovative welding products & solutions for NZ, Australia & South Pacific | Weldwell NZ