Saci E-Pool Swimming Pool Pump Instruction Manual

Saci E-Pool Swimming Pool Pump Instruction Manual

1 SAFETY RULES

⚠ Before installing and using the product:
– Carefully read the whole of this manual.
– Check that the data indicated on the plate is desired information and is appropriate for the installation, and in particular that the nominal voltage of the pump is compatible with that of the installation.
-The installation and maintenance must be carried out solely and exclusively by authorised personnel, responsible for making the electrical connections in accordance with the current safety regulations.
– The pump must not be used by people with reduced physical, sensory or mental capabilities, or without the due experience or knowledge, except if a person responsible for their safety has explained the instructions and supervised their operation of the pump.
– Do not let children play with the pump.
– The manufacturer accepts no liability for damage caused by improper use of the product and shall not be held responsible for damage caused by maintenance or repairs carried out by unqualified staff and/or with non-original replacement parts.
– The use of unauthorised replacement parts, alterations of the product or improper use shall automatically render the product guarantee null and void.

⚠ During normal operation:
– Before removing the cover of the variator, connect the mains voltage and wait 5 minutes for the electronic circuit board to discharge any residual voltage inside.
– Never disconnect the variator while the motor is rotating. This action can cause irreparable damage to the speed variator and affect the other electronic systems connected to the same electric grid.
– Although the pump is not operational, the electrical supply must still be cut off to the whole variator for any maintenance work. – If there are any anomalies in the installation, the speed variator can be stopped manually using the button STOP for this purpose.
– If the inputs and outputs of the speed variator have not been wired, ensure the cable glands are tightened properly, so that the electronics of the speed variator remain sealed from the moisture in the room.

2 TECHNICAL DATA

Nominal values:
Limits of use:
– Minimum ambient temperature: -10ºC
– Maximum ambient temperature: +40ºC
– Variation in the supply voltage: +/- 10%

3 INSTALLATION / ASSEMBLY

⚠ BEFORE INSTALLING THE PUMP, CAREFULLY READ THE WHOLE OF THIS MANUAL AND CONSULT THE SAFETY RULES VALID IN EACH COUNTRY.
Installation of the pump:
– It must be installed in a well ventilated area, protected from damp and direct exposure to the sun and rain.
– Before making the electrical connections, ensure the cable used to provide power to the pump is not live.
– Carefully verify the electrical data indicated in the specifications plate of the speed variator before connecting the electric current.
– The electric power cables to the pump must be of the correct size for the nominal consumption of the motor and the length of cable required.
– Also ensure that the grid has electrical protection; a high-sensitivity differential switch (30 mA, class B for industrial applications) is particularly recommended.
– In addition to the differential switch, it is advisable to install magnetothermal protection and a voltage disconnect switch to control the power supply to the pump.

4 ELECTRICAL CONNECTIONS

5 SCREEN FORMAT

6 MAIN SCREEN

This screen will show the current status of the pump:

You can directly view the instantaneous rotational frequency of the motor, the pressure of the installation (only if the pressure transducer is installed) and the instantaneous consumption of motor. In brackets, just to the side of the instantaneous consumption, you can see the nominal consumption of the motor entered in the start-up wizard (point 8 of this manual).

From this screen, if you click on the keys ( ▲) or (▼ ) you can directly access the display menu. This acts a short cut for checking data you need view without having to access the settings menu.

7 OPERATION MODE

Like all pumps designed for swimming pool filtration, its main objective is to keep the water clean and in optimum condition. Its main characteristic and new feature is that, with the logic of the speed variator, this process achieves high energy savings thanks to simple and intuitive management software, providing greater protection for the pump, and completely eliminating the need to install a conventional electric panel.

The system it allows one single pump to operate in an installation, or a variety of pumps connected together in parallel (up to 8 pumps) using its speed variator.

We have a daily setting of various filtration sequences (up to 4 sequences every day), in which we can also indicate how many pumps participate in this filtration (if there is more than one pump installed), and the operating frequency of the pumps.

You can configure the settings for the days needed from the menu to alternate the operation of the pump(s) that will be involved in the filtration (from 1 day to 14 days).

The default of pump operation mode is filtration. Once time bands and the days of the week on which filtering is required have been indicated, the pump(s) will filter at the frequency indicated for each band. It is here where we must take into account that the longer the time the greater the energy savings.

If there is a pressure transducer installed, the system will monitor the pressure of the installation at all times, to warn if it detects excess soiling in the filter. Once this warning has been received, or at any other time, when the button “BACK WASH” is pressed, a simple wizard will guide you through the installation filter cleaning. This wizard will tell you to move the filter valves to cleaning mode, then rinse and finally back to filtration.

8 FIRST START-UP

N.B.: It is important to know that, if there is a set of pumps connected together, only one of the pumps should be programmed, as all of the information entered is automatically copied to the other pumps that make up the network. The only action that must be performed on the rest of the pumps is to select the rotation direction, since it is the only data that is particular to each pump.
The first time you apply voltage to your unit, you will see parameter 1.1 that belongs to menu 1 General Setup, which at the same time is the start-up wizard.

This is the last screen of the start-up wizard, and it is the only one that must be done individually for each of the pumps that make up the filtration pump network, as it is independent for each model. The rest of the parameters entered in the wizard are automatically copied from one pump to the next.

9 SETUP MENU (DIAGRAM)

10 SETUP MENU

11 WARNINGS/ALARMS

12 WARRANTY

THE GUARANTEE OF THE VARIATOR IS 24 MONTHS FROM THE DATE OF PURCHASE: THE USE OF NON-ORIGINAL SPARE PARTS, ALTERATIONS OR IMPROPER USE SHALL RENDER THE PRODUCT WARRANTY VOID.

13 DISPOSAL AND ENVIRONMENTAL ASPECTS

To dispose of the parts that comprise the variator, you must abide by the current regulations and laws of the country where the product is used. In any case, do not dispose of polluting parts into the environment.

14 DECLARATION OF CONFORMITY

Bombas Saci, S.A., CL/ Can Cabanyes 50-58, Pol. Ind. Circuit de Catalunya, 08403, Granollers (Spain) declares, under its full responsibility, that the product to which this manual refers complies with the following European Directives and national action provisions:

– Directive 2004/108/CE about electromagnetic compatibility (EMC)
– Directive 2006/95/CE about low voltage
– Directive 2002/96/CE and 2003/108/CE about hazardous substances (RAEE)
– Directive 2002/95/CE about hazardous substances (ROHS)
– Basic EC regulation EN 55011 (EMC)
– Basic EC regulation EN 61000-6-2 (EMC)
– Basic EC regulation EN 61000-6-1 (EMC)
– Basic EC regulation EN 62477-1 (Safety)

CERTIFICADO DE PRUEBAS, TEST CERTIFICATE,

BARCELONA – Oficinas centrales
Can Cabanyes, 50-58
Pol. Ind. Circuit de Catalunya
08403 GRANOLLERS
Barcelona – Spain
Tel. +34 93 384 23 51
Fax +34 93 384 29 00
saci@sacipumps.com

A CORUÑA – Delegación
Pol. Ind. Pocomaco
Parcela D-31
15190 A CORUÑA
Spain
Tel. +34 98 129 96 88
Fax +34 98 129 96 16
sacicoruna@sacipumps.com

sacipumps.com

Cat. MeM Rev. 01-10-2017

Documents / Resources

| Saci E-Pool Swimming Pool Pump [pdf] Instruction Manual
E-Pool Swimming Pool Pump, E-Pool, Swimming Pool Pump, Pool Pump, Pump
---|---

References

• BOMBAS SACI

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>