Farfarer British Design Swiss Made Watches Instruction Manual
- June 11, 2024
- FARER
Table of Contents
- Farfarer British Design Swiss Made Watches Instruction Manual
- WATCH CARE
- GENERAL CARE
- CLEANING
- STAINLESS STEEL CROWN WITH BRONZE CAP
- WATER RESISTANCE
- SERVICING & REPAIRS
- WATCH STRAPS
- WARRANTY & GUARANTEE
- BRITISH DESIGN. SWISS MADE.
- MANUAL WINDING
- SETTING THE TIME
- SETTING THE DATE
- SETTING THE DAY
- SCREW IN CROWN
- UNIDIRECTIONAL BEZEL
- INTERCHANGEABLE STRAPS
- RUBBER STRAP
- INTERCHANGEABLE STRAPS
- RUBBER STRAP
- METAL BRACELET
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Farfarer British Design Swiss Made Watches Instruction Manual
WATCH CARE
(Noun) Explorer Wayfarer, Seafarer, Farfarer
GENERAL CARE
Every Farer Automatic has been constructed to withstand the test of time. However, like all precision mechanical devices, your watch needs a regular service and proper care. Avoid excessive exposure to direct sunlight or heat. Normal sports activities will not affect the watch’s functionality. However, any type of violent shock may upset the movement and ability to keep correct time.
CLEANING
Watch case and steel bracelet. Gently wipe off the front and back of the
watch case or steel bracelet using a clean and slightly damp cloth. Dry and
polish your watch with the Farer superfine microfibre cloth.
Nato and rubber strap. Using luke warm water and hand soap gently rub the
strap until clean. Rinse with water, lay flat and leave to air dry.
STAINLESS STEEL CROWN WITH BRONZE CAP
The signature Farer bronze cap will patinate as it is exposed to the elements.
It may also over time develop a soft green tone depending on the acidity of
the wearer’s skin. If you wish to return the bronze cap to its original
condition,use a pinhead-size blob of metal polish and a fine polishing cloth
to gently remove any tarnish.
We recommend Peek metal polish.
WATER RESISTANCE
With the crown screwed in the WR is 200M/656FT. To screw the crown in, push
the crown right against the case and screw it carefully down clockwise until
it can turn no further.
IMPORTANT: After changing time, day or date Push the crown right against the
case and screw carefully down clockwise until it can turn no further to ensure
the full WR of your watch.
Your watch case, bracelet, nato and rubber strap should be rinsed thoroughly
in fresh water after being in contact with salt water. Wipe dry with a soft
cloth.
IMPORTANT: Do not use chemicals to clean your watch.
SERVICING & REPAIRS
All component parts are manufactured from the best materials. However, some parts are subject to natural wear. This is why we recommend that you have a maintenance service carried out on your watch every 3-4 years. Contact Farer for further information about our servicing programme or use a reputable watch technician who has an expertise in Sellita movements. If in doubt about the quality of service needed to uphold your warranty, please contact Farer. Your warranty may be affected if your watch is not properly serviced.
WATCH STRAPS
Watch straps are guaranteed to be free from manufacturing defects at the time of purchase but are not otherwise guaranteed because they are expected to undergo normal wear and tear. Leather watch straps typically have a finite life span, as perspiration and body oils degrade natural leathers over time.
WARRANTY & GUARANTEE
Your Farer watch is covered against manufacturing defects for 60 months / 5
years from date of purchase. Upon presentation of the warranty card duly
completed, dated and signed by the authorised Farer dealer, alongside proof of
purchase, the right of guarantee will be honoured by the official Farer
Service Centre.
This warranty excludes the watch case, glass, crown, straps and any damage
caused by excessive use or under conditions exceeding water resistance
limitations. Please contact Farer to obtain more information.
BRITISH DESIGN. SWISS MADE.
Congratulations on purchasing a Farer watch.
At Farer, we are passionate about creating watches that are the perfect
companions for life’s adventures. Farer watches are inspired by the halcyon
era of watchmaking, when bold colours and contrasting textures were combined
with the very best craftsmanship. Our watches are
named after iconic British explorers, vessels and locations that perfectly
define the true spirit of Farer: ambition beyond the ordinary.
Thank you for your support. Here’s to the journey.
MANUAL WINDING
Your watch has an automatic movement, which means that the motion of your wrist is all your watch needs to function. However, if you have not worn your watch recently, you can give the mechanism a boost either before or after you have set the time. Unscrew the crown anti- clockwise, gently pull out the crown to position 1,wind the crown clockwise 10-20 times to start the movement. This will power the mainspring of your watch. The rotor will continue to wind the watch as you wear it. Fully wound your watch has a power reserve of approximately 41 hours.
SETTING THE TIME
Unscrew the crown anti-clockwise, gently pull out the crown to position 3, turn the crown until the correct time is displayed.
SETTING THE DATE
Unscrew the crown anti-clockwise, gently pull out the crown to position 2,
turn the crown clockwise to advance the date indicator.
IMPORTANT: Only advance the date when the time is after 2AM and before 10PM
SETTING THE DAY
Unscrew the crown anti-clockwise, gently pull out the crown to position 2,
turn the crown anti- clockwise to advance the day indicator.
The day can be displayed in English or French. The mechanism automatically
displays only the language initially selected
IMPORTANT: Only advance the day when the time is after 2AM and before 10PM.
SCREW IN CROWN
To ensure the full WR of your watch the crown must be screwed in. Push the crown right against the case and screw carefully down clockwise until it can turn no further.
UNIDIRECTIONAL BEZEL
Turn the bezel anti-clockwise until the zero arrow marker is directly opposite the minute hand. As time passes, you can quickly and easily read the elapsed time on the bezel. The bezel has an in- built safety ratchet mechanism for diving so that the bezel can only be moved forward
INTERCHANGEABLE STRAPS
Our strap mechanism allows you to easily change the look of your watch in seconds, without the aid of a tool.
RUBBER STRAP
To fit the strap, pull back the levers to release the pins. Whilst holding back the levers, place pins into lug holes. Once lined up, release the lever to secure the strap.
INTERCHANGEABLE STRAPS
Our strap mechanism allows you to easily change the look of your watch in seconds, without the aid of a tool.
RUBBER STRAP
To fit the strap, pull back the levers to release the pins. Whilst holding back the levers, place pins into lug holes. Once lined up, release the lever to secure the strap.
METAL BRACELET
We recommend taking your watch and bracelet to a reputable watch store or
jeweller, who will measure your wrist and remove links to ensure an exact fit.
When measuring your wrist, there should be sufficient room for your index
finger to pass between your wrist and the strap.
After removing any links to fit to size, the Farer clasp should be central on
the strap and directly opposite the watch case.
To fit the bracelet pull back the levers to release the pins. Whilst holding
back the levers, position the bracelet between the lugs. Once lined up,
release levers to secure the bracelet
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>