ROOST CONCEPTS 719.475.2624 Mullet License Plate Holder Instruction Manual
- June 1, 2024
- ROOST CONCEPTS
Table of Contents
INSTALL DIRECTIONS Rev2: THE MULLET PLATE HOLDER
Tools: Marking pen, drill bits and power drill.
Fitment Notes
Most stock license plate fenders will work with The Mullet. However, here are some numbers to check. Max allowable thickness of mounting surface on dirt bike is 0.25in (6.4mm). There is no minimum thickness. If fender length is shorter than 4.3in (110mm) The Mullet will require horizontal installation to avoid contact with the taillight/main fender.
STEP 1: Mount plate to The Mullet
- Your plate mounts on the flat side (1a) of The Mullet holder.
- Install the plate mounting hardware into the four corners of the plate. Note the washers should be touching The Mullet holder on the backside (1b). No washers are needed under the screw heads.
- Tighten the four stainless steel bolts until The Mullet arms just start to compress. Do not overtighten. Stainless Nylok nuts are included to secure the bolts at low torque.
719-475-2624-Mullet-License-Plate-Holder-overview-1.jpg" alt="ROOST CONCEPTS 719 475 2624 Mullet License Plate Holder - overview 1" width="1041" height="282" srcset="https://manuals.plus/wp-content/uploads/2024/04/ROOST- CONCEPTS-719-475-2624-Mullet-License- Plate-Holder-overview-1.jpg 1041w, https://manuals.plus/wp- content/uploads/2024/04/ROOST- CONCEPTS-719-475-2624-Mullet-License- Plate-Holder-overview-1-550x149.jpg 550w, https://manuals.plus/wp- content/uploads/2024/04/ROOST- CONCEPTS-719-475-2624-Mullet-License- Plate-Holder-overview-1-1024x277.jpg 1024w, https://manuals.plus/wp- content/uploads/2024/04/ROOST- CONCEPTS-719-475-2624-Mullet-License- Plate-Holder-overview-1-768x208.jpg 768w" sizes="(max-width: 1041px) 100vw, 1041px" />
STEP 2: Mark and Drill Holes
- Determine desired position of the plate on the fender. Use the mounting template and the Mullet holder to check for interference with the taillight or any main fender features. Mounting template color may vary.
- Use the included drill template to mark and drill the holes. Refer to table on next page for drill bit sizes.
- Use a punch (or nail tip) to indent the drill locations. This prevents the bit from wandering off location.
- Use light pressure drill pressure when drilling plastic.
- Deburr the hole edges using a box cutter blade, or hobby knife blade.
- Continue to STEP 3 on next page.
719-475-2624-Mullet-License-Plate-Holder-overview-2.jpg" alt="ROOST CONCEPTS 719 475 2624 Mullet License Plate Holder - overview 2" width="1006" height="336" srcset="https://manuals.plus/wp-content/uploads/2024/04/ROOST- CONCEPTS-719-475-2624-Mullet-License- Plate-Holder-overview-2.jpg 1006w, https://manuals.plus/wp- content/uploads/2024/04/ROOST- CONCEPTS-719-475-2624-Mullet-License- Plate-Holder-overview-2-550x184.jpg 550w, https://manuals.plus/wp- content/uploads/2024/04/ROOST- CONCEPTS-719-475-2624-Mullet-License- Plate-Holder-overview-2-768x257.jpg 768w" sizes="(max-width: 1006px) 100vw, 1006px" />
| Center Hole | Vertical Orientation | Horizontal Orientation |
|---|---|---|
| Required | Required for vertical plate orientation (check | |
| local laws before using this orientation) | Required for horizontal plate |
orientation
1/4” Drill Bit (6.4mm)| 5/16” Drill Bit (8mm)| 5/16” Drill Bit (8mm)
STEP 3: Mount the Mullet
- Place The Mullet holder onto the fender, choosing your preferred mounting orientation. The Mullet locating pin should fall into one of the two 5/16” (8mm) holes depending on the desired orientation.
- Horizontal mounting is required in most locations to be legal.
- Vertical mounting is best for low profile storage of the plate when it is not needed.
- Thread the thumbscrew through the backside of the fender and into the plate holder.
- When turning the thumbscrew, it must grab into the material of The Mullet. This makes the first install require slightly more torque to get it going. This is normal.
- Keep tightening until the knob tightens The Mullet holder securely on the fender.
- Torque tightly using only your hands.
- To remove it, simply undo the knob and remove the plate. Consider stashing the knob in the holder center hole.
Now, get after it!
Questions ? Email us at support@roost-concepts.com
719-475-2624-Mullet-License-Plate-Holder-icon.jpg" alt="ROOST CONCEPTS 719 475 2624 Mullet License Plate Holder - icon" width="291" height="150" />
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>