Honeywell 8733500 Electronic Deadbolt Instruction Manual

Digital Touchscreen Deadbolt
Instruction Manual

Important
Use the QR code below for the most up to date instructions:

https://hymaninc.com/a/qrcode-rsi/yYjpT9pDXu9vFA

Tools Needed for Lock Installation:

• Phillips Screwdriver

Read this manual carefully before installing and operating!
Model 8733500

Installation Overview

Package Includes:

Please carefully check the above list to confirm all items have been received. If any items are missing, please contact Consumer Assistance. (See back for contact information)

Install Enclosed Latch and Strike Plate

Do not over-tighten latch screws.

TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET :

1. Hold latch with numbers facing forward and thumb pressing on the bolt.
2. Rotate the cylinder cover clockwise.
3. Pull and twist the extension plate all the way out.
4. Rotate the cylinder counter clockwise so that the marking aligns with the 2-3/4” position indicator.

The latch plate on the door needs to be straight and not protruding from door. Make adjustment before installing or this will cause problems with bolt fitting into latch hole.

Preparation for Interior Assembly.

Remove (J) Screw from inside the battery compartment within the (B) Housing to release the Mounting Plate (C).

Screw Mounting Post (M) into holes on Mounting Plate (C).

Install Exterior Assembly

Check that the Rubber Gasket is secured on the Exterior Assembly. Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set in the VERTICAL POSITION.
Route the Control Wire through the door UNDER the Deadbolt Latch Set. Make sure the door is shut, lock and unlock using the key, ensure that the latch is operating smoothly and is aligned properly without scraping the strike plate.
If not, go back to step 2 and ensure you followed the steps.

Work with the door open (K) screw goes into the door to prevent the lock from shifting and is optional.

Install Interior Assembly

NOTE: Make sure the connector dots line up with the dots on the control wire

NOTE: Make sure the Turn Knob is in the vertical position.
Be careful not to pinch the control wire when assembling.

Test the lock

****

Lock and unlock using the turn knob make sure the latch is opening and closing easily. If not, go back to step 2 and ensure you followed the steps.

Install Batteries and Cover

This Electronic lock requires (4) High Quality AA Alkaline batteries. When all 4 batteries are installed in the correct position, you should hear 2 beeps and the touchscreen will illuminate.
The Lock motor will engage and do a series of locking and unlocking motions in order to automatically determine your door “Handing” (left or right handed door).
When completed the lock will beep and the touchscreen will flash.
NOTE: Do not touch the touchscreen or turn knob until the light turns off.
Do not use rechargeable batteries or non-alkaline batteries.

Testing Operation

Test the lock button with door open

Test unlocking

Before Opening Door Let Motor Complete Cycle
NOTE: Let lock operation complete before attempting another action
Preparing Door
Tools Needed for Door Preparation (if there is no knob hole):
NOTE: Skip this step if your door comes with pre-drilled holes.

• Drill
• 2 1/8” Hole Saw
• 1” Hole Saw
• 3/4” Chisel

Refer to Template included for Door Prep Instructions

Strike Plate Installation
NOTE: The strike plate on the door frame needs to be straight and not protruding from door frame. Make adjustment before installing or this will cause problems with bolt fitting into latch hole.

Programming Instructions

Read this manual carefully before Programming and operating!

Complete all the programming steps in the programming mode within 5 seconds
Do not press touchscreen until it stops illuminating, after you put in batteries

1. Creating Administrator Code
   Touch screen to wake up lock.
   Do not share admin code.

2. Adding a User Code
   Touch screen to wake up lock.

3. Unlocking Door with User Code
   Touch screen to wake up lock.
   TO LOCK DOOR, wake up lock and press Lock button
   PROGRAMMING RECORD****

4. Deleting a User Code
   Touch screen to wake up lock.

5. Deleting All User Codes
   Touch screen to wake up lock.

6. Additional Programming Functions
   Touch screen to wake up lock. Wake up lock before each function.
   Programming Symbols
   Lock / Clear
   Unlock / Programming
   Administrator Code
   Automatic Lock Function
   SET OR CANCEL AUTO LOCK
   You can set the lock to automatically close after each time the lock is opened. Time value range = 20 – 900 seconds, enter the following:
   Set Auto Lock: → Unlock →5 Unlock →  Time Value → Unlock
   Hear 1 beep and Light Indicator illuminates green.
   To cancel Auto Lock set the time to 00, enter the following:
   Cancel Time Value Auto Lock: →Unlock → 5 Unlock → 00→ Unlock Hear 1 beep and Light Indicator illuminates green.
   TEMPORARILY DISABLE:
   While in Auto-Lock mode, unlock door using . Immediately turn the locking knob back to the unlocked position. You will hear 1 beep and the light indicator will illuminate green.
   The Auto-Lock mode is now disabled.
   RESTORE:
   To restore the Auto-Lock function, turn the locking knob by hand to the locked position, wait more than 2 seconds or press the Lock button on the touchscreen.
   Vacation Mode
   With Vacation Mode enabled, the system enters into low-power consumption mode.
   During this mode, all buttons and functions will be disabled until they are re-enabled.
   ENABLE:
   Unlock → 10 → Unlock →1 →Unlock light indicator illuminates green.
   Once the door is locked, vacation mode will be engaged and all buttons and functions will be disabled.
   DISABLE:
   To disable the Vacation Mode, you must press and hold unlock for more than 3 seconds, then input followed by unlock to unlock the door. The light indicator will illuminate red.
   Vacation Mode is now disabled. NOTE: If you only press unlock for more than 3 seconds but do not input , Secure Lock-out period the system will remain in Vacation Mode.
   Warning sounds and LED flashes red after 4 incorrect code attempts: Touchscreen shuts down for 60 seconds.

7. Additional Programming Functions
   SOUND ON AND OFF
   You can “mute” or turn the “sound on” on your lock by entering the following.
   (Factory setting is sound on).
   →Unlock →6 → Unlock → 1 or 2→ Unlock
   1 = Sound Off
   2 = Sound On
   Sound Off (1) – Light Indicator illuminates green.
   Sound On (2) – Hear 1 beep and Light Indicator illuminates green.

Restore Factory Settings
To reset the lock to the original factory settings including the
Programming Code and all User Codes follow these steps:

1. Remove one battery for 10 seconds.
2. Reinsert the battery and wait for a long and short beep
3. Press Lock 3 times within 3 seconds.
4. The lock will beep and the light indicator will turn green.

Low Battery Warning
Beeps and LED flashes red 7 times. Replace with good quality alkaline batteries.
Note: Removing batteries does not erase active Administrator or User Codes.
Consumer Friendly Message Guide

attempt
Power on:| 1 long beep and 1 short beep and LED illuminates green
Chip Reset:| 1 long beep and 1 short beep and LED illuminates green (may occur several times or once in a while)
Lock Error:| 3 long beeps LED flashes red three times
Repeat operation after Lock Error:| 2 short beeps three times LED flashes red six times

Troubleshooting

incorrect position.
• Remove Interior Assembly and reposition the Interior Knob. With the Deadbolt Latch retracted verify that the tailpiece is vertical.
Lock will not function electronically| • Check that all batteries are fresh high quality Alkaline Batteries.
• Check for proper polarity (+ -) of all batteries.
• Check that the Control Wire is attached to the Interior Assembly and not damaged.
• Check each wire for loose or disconnected wires.
• Disconnect the wiring harness and reconnect the wiring harness.
Lock gives error signal when opening or
locking and Deadbolt Latch will not extend or retract completely when door is closed| • Unlock door using Key or Interior Knob. While door is open, check that the Deadbolt Latch operates smoothly.
• Check for proper alignment of the strike plate, adjust as needed to assure there is no binding against the Deadbolt Latch.
• Make sure tail piece is in the vertical position and straight up and down.
Deadbolt Latch is sticking| Installation screws of the lock may be too tight and have to be loosened.
• Remove Interior Assembly.
• Slightly loosen the Mounting Plate screws.
• Lock and unlock using the Key.
• Reattach Control Wire and Interior Assembly.
Touchscreen not working| • Wait 60 seconds, touchscreen may be locked out due to incorrect code.
• Replace with 4 high quality alkaline batteries.
Touchscreen beeps and LED flashes| • Replace with 4 high quality alkaline batteries.

DO NOT RETURN TO STORE!
Problems Installing or Using this Product?
Call Us First!
Contact Us 1-800-860-1677 Ext. 1801
locks@LHLPinc.com
Support hours M-F 8am – 8pm EST

CONSUMER ASSISTANCE

EMAIL: LHLPCustomerService@LHLPinc.com WEBSITE: www.honeywellsafes.com
ADDRESS: Consumer Assistance Dept. LH Licensed Products, Inc., 860 East Sandhill Avenue Carson, CA 90746 USA
TELEPHONE: US/Canada 1-800-860-1677 Ext. 1801 (Toll Free)
Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-860-1677 to complete your call. (Toll Free)
Australia 0011-800-5325-7000 (Toll Free)
Germany/New Zealand 00-800-5325-7000 (Toll Free)
Other Countries XX-310-323-5722 (Toll Charges Apply)
XX- Dial U.S. Country Code first
CALL CENTER HOURS: US/Canada 8am – 5pm (Pacific) Mon – Fri (Subject to change)
CALL BACK HOURS: Other Countries 8am – 5pm (Pacific) Mon – Fri (Subject to change)
Pacific**- Local time in Los Angeles, CA, USA

• Insert correct Country Code
  Local Time based on Los Angeles California USA
  INTERNATIONAL CALL BACK HOURS:
  If you need to speak with a consumer assistant and cannot contact us during the Call Center hours above, please send an email or leave a telephone message, including your Name, Telephone Number and the best time for us to contact you during the Call Back hours above and we will make our every effort to contact you and help answer any of your questions or concerns.
  Limited Lifetime Mechanical and Finish Warranty / 1 Year Limited Electronics Warranty
  This product comes with a limited lifetime mechanical and finish warranty and a one year limited electronics warranty to the original residential consumer against defects in material and workmanship under normal use as long as the original residential purchaser occupies the residential premises upon which the product was originally installed.
  ORIGINAL RESIDENTIAL CONSUMER
  This warranty is not transferable, and applies to the original purchaser only, as long as the original purchaser occupies the residential premises upon which the product(s) was originally installed. Proof of purchase (original sales receipt) and ownership must accompany all warranty claims.
  All non-homeowner purchasers (including purchasers for industrial, commercial and business use) are not covered under the terms of this warranty.
  WHAT IS NOT COVERED
  This warranty is null and void if the product was used for purposes for which it was not designed. This warranty DOES NOT COVER normal wear and tear of parts or damage resulting from any of the following: negligent use, misuse or abuse of the product, or use contrary to or in violation of written instructions provided by LH Licensed Products, Inc. Further, this warranty does not cover Acts of God, such as fire, flood, hurricanes and tornadoes. This warranty DOES NOT COVER scratches, abrasions, deterioration due to the use of paints, solvents or use of cleaners containing abrasives, alcohol or other solvents, whether performed by a contractor, service company, or yourself. This warranty DOES NOT COVER product(s) used in commercial
  applications, used in common area applications, disassembly, repair or alteration by anyone other than LH Licensed Products, Inc., improper installation or exposure to extremes of heat or humidity. This warranty DOES NOT COVER any losses, injuries to persons or loss of property, general damages or costs, and shipping and freight expenses required to return product(s) to LH Licensed Products, Inc. LH Licensed Products, Inc. shall not be liable for any indirect, incidental or consequential damages of any nature relating to this lock. LH Licensed Products, Inc. is also not responsible for costs associated with removing or reinstalling the product.
  ADDITIONAL TERMS
  LH Licensed Products, Inc. does not authorize any person to create for it any obligation or liability in connection with the Product. LH Licensed Products, Inc.’s maximum liability here under is limited to the original purchase price of the Product. No action arising out of any claimed breach of this warranty by LH Licensed Products, Inc. may be brought by the original residential purchaser more than one (1) year after the cause of action has arisen.
  AUSTRALIAN CONSUMER LAW**
  Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Manufactured by:
LH Licensed Products, Inc.
860 East Sandhill Avenue
Carson, CA 90746
The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell
International Inc. makes no representations or warranties with respect to this product.
www.honeywellsafes.com
M8733500 E V0

References

• Honeywell Safes

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>