Juhui 890MAX 3 Button Remote Controls Instruction Manual

June 1, 2024
Juhui

Juhui 890MAX 3 Button Remote Controls

Juhui-890MAX-3-Button-Remote-Controls-PRODUCT...

Product Information

Specifications

  • FCC Compliance: Part 15 of FCC Rules
  • RF Exposure: Meets general RF exposure requirements
  • Portable Use: Can be used in portable exposure conditions without restriction

Frequently Asked Questions

  • Q: What should I do if I encounter interference while using the device?
    • A: If you experience interference while using the device, ensure that the device is not causing harmful interference to other equipment. Additionally, the device must accept any interference received, including that which may cause undesired operation.

Models

Can be used as a replacement remote control for 80 Series, 970 Series, and 370 Series LiftMaster remote controls.

Compatible with 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. Make sure the garage door opener has a working light bulb because it is a programming indicator. For use with gate operators, commercial door operators, or other products that are 315 MHz or 390 MHz and have a Learn button. Refer to your product manual for the location of the Learn button.

WARNING: To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

  • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls.
  • Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
  • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

PREPARE

Juhui-890MAX-3-Button-Remote-Controls-FIG-2

Locate the Program button on the remote control

PROGRAMMING THE REMOTE CONTROL

  1. To enter programming mode, press the Program button until the LED on the front of the remote control turns on.
  2. Press and release the Learn button on the garage door opener.
    • The Learn LED will light.
    • Within 30 seconds…
  3. Press and release the remote control button you want to use…
    • Check to see if the garage door opener light bulb blinks.
    • If not, wait for the remote control LED to light solid then slowly press and release the remote control button again.
    • Repeat until the light bulb blinks.
    • DO NOT press the button after the light bulb blinks.
  4. To exit programming mode, press any remote control button except the button that was just programmed.Juhui-890MAX-3-Button-Remote-Controls-FIG-8
  5. To test, press the programmed button on the remote control…
  6. Install the visor clip (not applicable for Model 890MAX).

HOW TO USE THE REMOTE CONTROL

Juhui-890MAX-3-Button-Remote-Controls-FIG-10

  • Press and hold the button down until the door or gate starts to move. The remote control will operate from up to 3 car lengths away on typical installations. Installations and conditions vary, contact an installing dealer for more information.
  • Additional buttons on the remote control can be programmed to operate up to 3 devices such as additional garage door openers, light controls, gate operators or access control systems.

BATTERY

The LED(s) on your remote control will stop flashing when the battery is low and needs to be replaced. To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery with only 3V2032 or 3V2016 coin cell batteries (depending on the model). Dispose of old battery properly.

Juhui-890MAX-3-Button-Remote-Controls-FIG-11

WARNING

To prevent possible SERIOUS INJURY or DEATH:

  • NEVER allow small children near batteries.
  • If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

  • Replace ONLY with 3V2032 coin batteries.
  • DO NOT recharge, disassemble, heat above 212° F (100° C) or incinerate.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER-SERVICEABLE PARTS.

Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

REPLACEMENT PARTS

  • 3V2032 Lithium Battery (Models 893MAX & 890MAX)…………………..10A20
  • 3V2016 Lithium Battery (Model 895MAX) ……………………….10A19
  • Visor Clip (Model 893MAX) ……………….29B137
  • Visor Clip (Model 895MAX) ………………..29C151

FCC STATEMENT

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF warning for Portable device:

  • The device has been evaluated to meet general RF exposure requirement.
  • The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Juhui User Manuals

Related Manuals