Besun BB007 Baby Swing Chair User Manual

June 1, 2024
Besun

Besun BB007 Baby Swing Chair

Product Specification

Besun-BB007-Baby-Swing-Chair-FIG-1 \(1\)

CAUTION

  1. Do not charge with non-rechargeable lithium batteries.
  2. Practical in adult supervision.
  3. When charging with an adaptor, please take out the batteries.
  4. Do not use with mixed batteries
  5. The battery should be placed in the correct polarity.
  6. The exhausted battery should be removed from the product.
  7. No short circuit of power terminals.
  8. Forbid to use the non-matching adaptor, the input voltage of the adaptor is 100-240V/50/60HZ
  9. Keep the adaptor away from the child while using it.
  10. Check the adaptor, and accessory at regular periods. If you find any damage to the parts please stop using them.

Parts List

  • Besun-BB007-Baby-Swing-Chair-FIG-1 \(2\) A – Seat Frame
  • B – Base Frame
  • C – Remote Control
  • D – Power Adapter

Please make sure all parts are included before proceeding to assembly.

Optional Parts

CARE AND MAINTENANCE

  • Keep the product in dry places. To keep the product attractive – avoid prolonged sun exposure.
  • Check the condition of the bouncer regularly. Before each use check if it is assembled regularly.
  • Use only parts recommended and provided by the manufacturer.
  • Clean the swing regularly.
  • To clean plastic parts and tubes – use a damp cloth.
  • Padding can be hand-washed with a bit of delicate soap. Do not bleach!
  • The fabric of the seat pad can be cleaned with a damp cloth.

Assembly and Disassembly

  • Assembly
    • Attach Part A (Seat Frame to Part B (Base Frame) swing+ canopy
  • Disassembly

Table Assemble And Adjustable Backrest Guidance

  1. Align the fixing column with the hole in the middle of the bottom of the desktop, then align and fix the screws into four small holes.Besun-BB007-Baby-Swing-Chair-FIG-1 \(6\)
  2. How to clip the table on the seat frame
    • A. Clip on the round tube
    • B. Push down and snap it
    • C. Clip the bottom of the seat frame
    • D. Press the buckle up and fixeBesun-BB007-Baby-Swing-Chair-FIG-1 \(7\)
    • Adjustable backrest: Hold two side steel tube, and lift to adjust the recline of the backrest
    • Detach backrest Press buttons on the left and right sides and press down to detachBesun-BB007-Baby-Swing-Chair-FIG-1 \(9\)
    • Cautions: Infants and children are not allowed to stay in the swing during the above operation Above picture is for assembly installation only, product please refer to the actual.
    • Warning: Guardian should take good care of your child, prohibit play accessories and avoid getting hurt or swallowed!

Using Harness

  • Top hole Bottom hole Through the tape from the top hole first and then through the bottom hole, harden the tape
  • Put the baby into the seat, buckle up the seat belts

Adapter

  • Plug the Power Adapter (D) into the DC jack located on the Base Frame (B).
  • The USB port is also located on the base frame (B) Place the adapter (D) 100-240V 50/60HZ in the AC Outlet.
  • Do Not use a different Voltage.

Remote control

Besun-BB007-Baby-Swing-Chair-FIG-1 \(13\)

Panel

Besun-BB007-Baby-Swing-Chair-FIG-1 \(14\)

Batteries Installation

Besun-BB007-Baby-Swing-Chair-FIG-1 \(15\)

Instructions for Use

  1. Power Switch Button: Touch the one time and the indicator light will turn on, which means the power is on. Press the button a second time and the indicator light is turned off to turn off the power.
  2. Five swing speeds: the indicator light stands for the speed gears.
    • The swing angles are 18°/21°/23°/25°/31°.
    • Notice: The Indicator light will show ! and the swing will stop automatically when the motor is stuck.
  3. Timer: Touch the button of for the first time to set 8 mins swing, touch the second time to set 15 mins and the third time to set 30 mins swing.
    • The indicator light will show respectively as
  4. USB: This product can support a USB disk to play additional music. Insert the USB disk and then touch the function key, when the button lights up this will indicate that you can play music from the USB.
  5. Music:
  6. Touch to play built-in music.
  7. Touch and hold for two seconds to play the next song.
  8. When the USB disk is pulled out, touch it to play the built-in music.
  9. Volume: Press to increase the volume, and press  to turn down the volume.
  10. Bluetooth: To connect the bluetooth, turn on the bluetooth from the cell phone and connect with “BT-BABY”, when the button lights up then you can play music from bluetooth.
  11. If the swing shakes too much, check the safety lock and place the swing on a flat surface.

WARNING

  • FALL and STRANGULATION HAZARDS: Infants have suffered head injuries falling from swings and have been strangled in straps.
  • FALL HAZARD: Children have suffered head injuries falling from rockers.
    • ALWAYS use restraints. Adjust to fit snugly.
    • STOP using the product when the infant attempts to climb out approximately 9 months).
    • Stay near and watch the baby during use. This product is not safe for sleep or unsupervised use. If the baby falls asleep, remove the baby as soon as possible and place the baby on a firm, flat sleep surface such as a crib or bassinet.
    • NEVER lift or carry a baby in a rocker.
    • STOP using the product when the baby starts trying to sit up or has reached [maximum weight not to exceed 20 lbs.], whichever comes first.
    • ALWAYS place the rocker on the floor. Never use on any elevated surface.
  • SUFFOCATION HAZARD: Babies suffocate when seats are tipped over on soft surfaces.
    • NEVER use on a bed, sofa, cushion, or other soft surface.
    • Stay near and watch the child during use. This product is not safe for unsupervised use or unattended sleep.

FCC

FCC Compliance Statement
FCC Compliance Statements This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The base bracket should be installed and operated with a minimum distance of 10cm between the radiator and your body.

Clean & Maintenance

Clean

  1. Clean the base bracket and seat frame with a wet cloth and a mild detergent. Dry thoroughly then. Please do not use corrosive cleaner.
  2. Removable and washable fabric
    • Seat fabric: Clean it with a wet cloth and a mild detergent, and dry it.
    • Canopy: Take it off and put a little cleaner, wash it gently by hand. Rinse it with clean water, and then hang it to dry, avoiding exposure to the sun.
    • Pillow: Tear the Velcro off and take the pillow off. Put a little cleaner, wash it gently by hand, and then rinse it with clean water. Hang it avoiding sun exposure.

Maintenance

  1. Please check this baby swing regularly. Make sure each part is well connected and well installed. Stop using it for poor connection and connect/ install it again if necessary.
  2. This product contains electronic components, which shall not be used in water or in a humid environment. Please ensure the product is dry, and store it in a cool and dry place, avoiding direct sunshine for a long time.

Troubleshooting

Fast self-inspection solution below

Besun-BB007-Baby-Swing-Chair-FIG-1 \(27\) Note: For other trouble, please contact our customer service for help. Never disassemble and repair the swing by yourself.
IMPORTANT! KEEP IT FOR FUTURE REFERENCE. Before installing and using, please follow the instructions carefully to ensure the safety of your baby.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals