globe 18000140 Wireless Smart Doorbell Kit User Guide
- June 1, 2024
- globe
Table of Contents
globe 18000140 Wireless Smart Doorbell Kit User Guide
Illustrations may vuy from actuel unit,
Before returning to the store, please contact our support team for assistance
at l-888-543-138B
SAFETY INFORMATION
⚠ WARNING: To prevent possible serious injury or death, never allow small
children near batteries. If a battery is swallowed, seek immediate medical
attention.
⚠ WARNING: Do not dispose of batteries in fire.
Batteries may explode or leak.
⚠ WARNING: Risk of fire. Do not plug the chime into a power inverter.
PACKAGE CONTENTS
TOOLS REQUIRED
-
Installing the smut chime
Plug the chime in the desired location. -
Powering the doorbell button
• Remove the back by pushing in the tab on the bottom with a small flat-head screwdriver
• Rotate the battery cover LEFT and remove It
• Insert the battery POSITIVE POLE facing outward. Refer to figure below”‘
-
Testing
Temporarily position the doorbell button where it will be mounted. Press it to verify if the smart chime rings. If not, move the chime to a closer outlet and test again.
NOTE: Do not permanently mount the doorbell button until It Is working properly. The chime and doorbell button are already synced. The range can vary with location, temperature, and battery condition. -
Mounting the doorbell button
Option 1 – Double-sided tape
Remove the paper from both sides of the tape, apply it to the back of the doorbell button and mount onto a clean surface.
Option 2 – Screws
• Remove the back by pushing in the tab on the bottom with a small flat-head screwdriver
• Place the back on the door jamb and mark the two screw holes. Drill holes where you marked.
• Align the back, fasten screws and snap the front of the doorbell button back on.
CONNECTING INSTRUCTIONS
-
Download the Olobe Suite TM app from the 105 or Android store
Create an account and log in. Ensure your mobile device is running iOS 9.0/watchOS 2.0/Android™ 4.4 or higher. -
Connect
Ensure the doorbell kit is powered and all requested permissions are enabled on your mobile device:
Wi-Fi, Bluetooth, Location Services.
On the app’s home screen, select the + in the top-right corner and select “Add a device”. The app will detect it within a few seconds. When discovered, select “Add” beside the chime icon. -
Setup
Name your chime and choose which room to place it in. You can now control it directly from the app. -
Voice assistance
On the app’s home screen, select “Profile,” and select “Integration.” Choose your voice assistant and follow the instructions within the app.
Need help?
Select the MHow do I set device into pairing moden link on the “Scanw page and follow the in-app instructions.
SMART CHIME INDICATOR LIGHT
CONTROLLING THROUGH THE APP
Please note that the device UI panel is subject to change without any prior notice.
CONTROL
Volume
4-step: 25% – 50% – 75% – 100%
Mute options
Mute/Unmute
DEVICE SETTINGS
History
Access full ring history.
Indicator light
Customize how the chime indicator light behaves.
Notifications
Customize how you would like to be alerted when the doorbell is rung.
GENERAL SETTINGS
Delete or restore device
Restore factory settings to the device or remove it.
ROUTINES
Timer
The chime will be muted until the timer runs out.
Add a new schedule
The chime can be scheduled to mute at specific times throughout the day or
week.
DOORBELL BUTTONS
Tune selection
10 available tunes that can be assigned to any doorbell button connected to
the chime.
Naming
Assign a unique name to each doorbell button that will display when you are
notified.
Add/Remove
Connect up to 10 Heath Zenithl’ wireless doorbell buttons.
Low battery
Get notified when a battery needs to be replaced.
MANUAL CONTROL
No WI-Fl. No problem. Continues operating as a regular doorbell if internet connection is lost.
Volume
4-step: 25% – 50% – 75% -100%
Unmute
Press either of the volume buttons to unmute the chime.
Tune selection
Press the “Tune” button to play the next tune. The last tune played will be
assigned.
Low battery
If a doorbell button is pressed and the chime rings dingdong 3 times+ the
indicator light stays on for 10 seconds, the doorbell button battery is low.
TROUBLESHOOTING
A= cause B = solution
Chime doesn’t ring when a doorbell button is pressed
A) Doorbell button battery is not installed correctly
B) Make sure batteries are installed according to the diagram inside the
doorbell button.
A) Doorbell button battery is dead
B) Check the charge of the doorbell button battery and replace if necessary.
A) Chime is not receiving power
B) Make sure the plug-in chime has power.
A) Chime and doorbell button are not synced.
B) Follow the steps:
• Press and hold the “Tune” button on the chime until it sounds a “Beep-Beep•.
• Press the doorbel I button with in 10 seconds. The chime will sound a uBeep-
Beep” tone to indicate the doorbell button is synced.
• Press the doorbel I button to ensure operation.
A) The transmission codes of the doorbell button and chime don’t match.
B) Ensure the code of doorbell button and chime is consistent. Refer to “Code
conversion” instructions.
Doorbell button battery seems okay, but the chime does not work after installation.
A] The chime and/or doorbell button is mounted on or near metal.
BJ Metal reduces transmission range. Use 1/4 in. to 1/2 in.
(6 to 13 mm) wood shims to move the chime or doorbell button away from the
metal surface.
A) The chime is mounted near a concrete floor or wall.
BJ Concrete may reduce transmission range. Move the chime away from the
concrete surface.
A) The chime and doorbell button are installed too far apart.
BJ Move either one closer to the other.
The chime rings when not intended to.
AJ The chime is receiving interference from another wireless device.
BJ 2 options:
1. Convert the doorbell button and chime to lOOM code.
Refer to ucode conversion• instructions.
2. Reset the chime and doorbell button:
• Remove the doorbell button battery. Wait 30 seconds.
• Press and hold the doorbell button for 10 to 15 seconds within 60 seconds
after installing the battery Into the doorbell button.
• Press and hold the “Tune• button on the chime untll the chime sounds a
aBeep-Beep-Beep-Beep”.
•To re-sync the doorbell button and chime, press and hold the uTune” button on
the chime until the chime sounds a “Beep-Beep•.
• Press the doorbell button within 10 seconds. The chime will sound a •Beep-
BeepD tone to indicate the doorbell button is synced.
• Press the doorbell button to ensure operation.
CODE CONVERSION
Doorbell buttons and chimes that communicate with each other wirelessly. need to be running the same transmission code in order to work properly.
This item is able to toggle between 100M and 12E codes.
By default, the doorbell button and chime are set to 100M front door. No need
to convert the code for first usage.
Doorbell button
12E – Press the silicone button in the back for 3 seconds, the indicator
light of the doorbell button will flash quickly once, indicating the doorbell
button has been converted to the 12E code.
100M – Press the silicone button in the back for 3 seconds, the indicator
light of the doorbell button will flash 3 times. It Indicates the doorbell
button has been converted to 100M code.
Front and rear door – Press the silicone button in the back for 1 second
and release, doorbell button will be converted between front door and rear
door.
NOTE: doorbell button default pattern is front door.
While the desired tune is playing, press the doorbell button to lock in
selected tune. If the door be I I button is in rear door pattern, the doorbell
will only ring as “Ding”.
Chima
12E – After the power is turned on for about 3 seconds, the chime prompts
“Ding”, meaning the doorbell code is 100M. Within one minute, press and hold
the “+-n volume button and “Tune” button of the chime at the same time for
about 10 seconds. You will hear the prompt sound “beep-beep”, then release the
buttons, the chime will prompt “Ding Dong” which indicates that it has been
converted to the 12E code. In this pattern, we should use 12E code doorbell
button to sync and pairing.
100M – After the power Is turned on for about 3 seconds, the chime
prompts “Ding Dongn, meaning the doorbell code is 12E. Within one minute,
press and hold the “+n volume button and “Tune” button of the chime at the
same time for about 10 seconds. You will hear the prompt sound “beep-beep”,
after release the buttons, the chime will prompt “Dingn which indicates that
it has been converted to the 100M code. In this pattern, we should use 100M
code doorbell button to sync and pair.
NO WI-Fl. NO PROBLEM.
Continues operating as a regular doorbell if Internet connection Is lost.
Documents / Resources
|
globe 18000140 Wireless Smart Doorbell
Kit
[pdf] User Guide
18000140 Wireless Smart Doorbell Kit, 18000140, Wireless Smart Doorbell Kit,
Smart Doorbell Kit, Doorbell Kit, Kit
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>