HOMCOM A91-098 Wall Mounted Punching Ball Instruction Manual

: June 1, 2024
: HOMCOM

Table of Contents

PART LIST
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HOMCOM A91-098 Wall Mounted Punching Ball Instruction Manual

HOMCOM A91-098 Wall Mounted Punching Ball Instruction
Manual

PART LIST

HOMCOM A91-098 Wall Mounted Punching Ball Instruction Manual - Part
list

WARNINING: To avoid serious injury it is important that you adhere to the following guidelines:

A. Be sure to carefully follow all of the instructions contained herein
B. Make sure that you use suitable hardware to securely fasten the Platform to the wall and re-check before each use.
C. Be sure to install this Platform in an unobstructed area so that you do not get “bumped” while hitting the bag and people will not get hurt walking into the drum.
D. Use of any sports or exercise equipment subjects the user to a degree of risk. Users of this product must assume all risk of injury.
E. Do not use this Platform if any pary becomes wom, fatigued or defective.

HOMCOM A91-098 Wall Mounted Punching Ball Instruction Manual - Do not use
this Platform if any pary becomes wom

A-4 – 5/16″ x 1″ Carriage bolts and Hex Nuts
B-4 – 1/4″ x 2″ Carriage Bolts, Lockwashers,
and Hex Nuts
C-4 #10 x 3/4″ Flat-head Sheet Metal Screws
D-2 – Steel Angle Mounting Brackets
E-1 – Swivel Assembly
F-1 – Drum for Plalform
G-2 – Tubular Steel Support Brackets
H-1 – Wrench (for 1/4″ & 5/16″ Hex Nuts)
1-1 Striking Bag

DETERMINE LOCATION OF PLATFORM:
A. Locate the Platform at least three feet(3″)away form any docr or other obstruction.
B. This Platform has been specially designed to fasten to 16″on center wood wall studs.
C. If you have wood wall studs plan to mount your platform on these 16″ on center studs using 1/4″x1 3/4″ Lag Bolts(not supplied).
D. If installation is other than 16″ on center wood wall studs consult your local hardware dealer for suitable fastening device E. Locate the wood wall studs in your wall. Place on(1)of the steel angle Mounting Brackets (D)on a wood wall stud so that the bottom of the Mounting Bracket is set equal to the height of the intended user of the Platform. Note: Mounting Brackets should have the” slotted” sides facing each other.
F. Use a Carpenters Level to be sure the Mounting Bracket is” level”. Now, pencil circle Inside the three (3) holes of the Mounting Bracket.
G. Use an ice pick or small nail to create a” starter” hole in the middle of each circle. Use 1/4″x 1 3/4″Lag bolts(not supplied)to securely fasten to the wood wall stud.
H. Repeat with the second Mounting Bracket with the holes 16″ on center o match you16″on center wood wall studs. Make sure both Mounting Brackets are exactly the same height off the floor and parallel to each other.
Note: “Slotted” sides of Mounting Brackets must be facing each other
I. We repeat, if you do not mount his Platform on 16″or ceter wood wall studs- consult your local hardware dealer to procure suitable fastening devices(s)
ASSEMBLE THE PLATFORM:
A. Find the Drum(F) and use the four(4)flat-head Screws(C) to securely fasten the Swivel into the pre-drilled holes in the drum.
B. Insert the four(4)1/4″ x 2″Carriage Bolts(B)into the holes on the Swivel side of the Drum
C. Set the tubular steel Support Brackets(G)onto the Carrage Bolts(B)at the top side of the Drum. Now, attach the Lock washers and Hex Nuts onto the Bolts by hand-do not tighten.
D. Hit the heads of the Bolts so that they are” seated” and flush with the “face” of the Drum. Now, securely fasten the Hex Nuts with Wrench(H) which is supplied.
MOUNTING THE FLATFORM ON THE WALL:
A. Attach the Platform assembly (with Swivel and Support Brackets)to the Mounting Brackets already fastened to the wall.
B. Insert 5/16″x 1″Carage Bolts (A)into the” slot ” of the Mounting Bracket and through the holes in the Support Bracket. Note: Support Brackets must be” inside the Mounting Brackets. Be sure that the” shoulder” of the Carrage Bolt fits “squarely” into the “slots” of the Mounting Brackets.
C. Attach the Hex Nuts loosely onto the Bolts. Adjust up or down so that the Bolts are midway within the” slots”. Now use the Wrench (H) and securely tighten these Hex Nuts
D. Place your Speed Bag on the Swivels Hook. The button of the speed Bag should be approximately level with the users chin. If necessary, use the Wrench(H) to release the Hex Nuts on the Support Brackets from the Mounting Brackets and adjust up or down to suit the users height. Note: To avoid serious injury be sure that you do not allow the Platform to drop freely. Be sure to hold onto the drum while loosening the Hex Nuts.