ANCwear EKOH01 Open Ear Headphones User Manual
- June 1, 2024
- ANCwear
Table of Contents
ANCwear EKOH01 Open Ear Headphones
Product Information
Specifications:
- Model: Open Ear Headphones
- Version: 1.0
- Charging Port: Magnetic
- LED Indicator: Yes
- Controls: Power/Volume, Next/Previous
Product Usage Instructions
-
Headphone Controls
The headphones come with various controls such as Power/Volume, Next/Previous buttons, and a Magnetic Charging Port with an LED Indicator. -
Turning the Headphones On/Off
To turn on the headphones, press and hold the + Button until the LED Indicator flashes blue. The headphones will announce “Power On.” To turn off the headphones, repeat the same process. -
Pairing
To pair the headphones with a device, ensure they are turned off, then press and hold the + Button for 1 to 3 seconds until the LED Indicator flashes red and blue alternately. Access your device’s Bluetooth settings, find EK-OH**, and click to pair and connect. -
How to Wear
To wear the headphones correctly, position the ear hooks on your ears with the transducers resting in front of your ears. Incorrect wearing may cause discomfort. -
Volume Control
Adjust the volume by using the Volume + or Volume – buttons while the audio is playing. A beep indicates maximum volume. Listening at high volume may affect hearing and audio quality. -
Operating Instructions
The operating instructions detail functions like adjusting volume, next/previous song selection, pausing/playing during music playback, handling phone calls, and charging tips. -
Charging Tips
Use the provided Magnetic Charging Cable to charge the headphones. Ensure a full charge before first use and recharge when the battery is low. Charging typically takes about 2 hours. Follow the charging status indicators for proper charging. -
Storage and Maintenance
To avoid risks, do not disassemble or tamper with the product’s battery. Follow proper storage practices to maintain product integrity.
Frequently Asked Questions (FAQ)
-
Q: How long does it take to charge the headphones fully?
A: Charging typically takes about 2 hours for a full charge. -
Q: What should I do if the battery is low?
A: If the battery is low, recharge the headphones. The red light flashing indicates low power. -
Q: How do I know if the headphones are paired successfully?
A: The LED Indicator will stop flashing and remain steady once the headphones are successfully paired with a device.
Please read the instructions carefully before use
Headphone Controls
ON/OFF
-
Turn on the headphones：
Press and hold the “+” Button until the LED Indicator flashes blue.- the headphones will say: “power on”
-
Turn off the headphones：
Press and hold the “+” Button until the LED Indicator flashes blue.- the headphones will say: “Power off”
Pairing
- Start with the headphones turned off.
- Press and hold the “+” Button for 1 to 3 seconds until the LED Indicator flashes red and blue alternately.
- Open your (mobile phone/computer) device’s Bluetooth settings and select “EK-OH**”, Click the device to pair and connect.
How to Wear
- Pick up the headphones, bring them behind the back of the base of your neck, position the ear hooks on your ears, and then enjoy your music!
- Wearing your headphones the wrong way could cause discomfort. The transducers should rest in front of your ears.
Volume
How to change volume:
While your audio is playing, adjust the headphone volume by pushing either the
Volume + or Volume – buttons.
- A “beep” will sound when the volume is at its max.
- Listening with headphones at high volume may affect your hearing and the audio will be distorted.
Operating Instruction
| Function | Operation | Indicator |
|---|---|---|
| On | Long press on key for 1-3 seconds | Light is on |
| Off | Long press on key for 1-3 seconds | Light is off |
| Increase volume | Click the “+” button | “du” beeps when the volume is increased |
| Reduce volume | Click the “-” button | “du” beeps when the volume is increased |
Next/Previous
| ****
Double click “+”/”-” in the music state to switch the next/previous song
| ****
/
Pause/Play
| ****
During music playback, press and hold the “+” button for 1 second to pause/play music.
| ****
/
With phone access
| Voice announcement of caller’s number| ****
blue light flashing
Answer the phone
| Click the “+” button when an incoming call comes in.| ****
Blue light 5s slow flash
Decline the call
| ****
During a call, press and hold the “+” button for 1s.
| ****
/
Refuse to receive| On an incoming call, press
and hold the “+” button for 1s.
| ****
/
Answer the second incoming call while on a call
| Click the “+” button to hang up the first call and answer the second call;
Double-tap the “+” key to answer the second call and hold the first call
| ****
/
Charging Tips
The first use of the headset must be fully charged to the battery. In use, if only the red light flashes and the voice prompts low power, that the battery is low, then you need to charge the headset. The charging cable should be connected to the headset’s magnetic charging port, about 2 hours to fill. The charging status indicator flashes a breathing light, a full charge often a blue light.
Note:
Magnetic charging has a positive and negative pole correspond to each other
adsorption can be charged normally, but mustual repulsion can not be charged
or even cause a short circuit.
Storage And Maintenance
- Store the headphones in a cool, dry place. The working temperature should be 0~45°C(32~113°F). Working in a cold/hot temperature, highly humid area, or low air pressure environment may reduce the battery life.
- Keep the product away from heat sources, direct sunlight, combustible gas, or other liquids.
- Keeping the charging port dry before connecting to the charger will reduce the risk of damage.
- The headset can not soak seawater/salt water for a long time, and filling the magnetic suction part is easy to corrode.
- Clean the headphones with a soft dry cloth.
- Do not charge right after exercising, in case there’s sweat inside the charging port, which could lead to circuit burning while charging.
- If not used for a long time, please at least once a month full of electricity.
Warning
To avoid the risk of explosion, fire, or leakage from toxic chemicals, please
do not disassemble the product or replace, deform, or mutilate the battery.
Warranty
- One-year warranty for manufacturing defects.
- For any quality defects, contact us, and you will get A Full Refund or A Free Replacement!
Dear Customer,
We want to prosper and know this will be achieved best by providing a quality
experience to our valued customers like you. Please feel free to contact the
ANCwear service team and always here for you.
Yours sincerely, ANCwear Service Team
Customer Support:
- Email:
- [email protected]
- [email protected]
- [email protected]
- [email protected]
- Official Website: https://www.ancwear.com.
- YouTube: @ANCwear fit
- Instagram: @ancwear
- Facebook: @ANCwear
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, under part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used under the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.