ARTIST SMYC40 3D Printer User Guide

ARTIST SMYC40 3D Printer

Product Information

Specifications

• Compliance: Part 15 of FCC Rules
• Radiation Exposure: FCC Radiation exposure limits
• Minimum Distance: 20cm between radiator and body

Product Usage Instructions

Compliance with FCC Rules

This equipment complies with Part 15 of the FCC Rules, which means it operates within the regulations set by the Federal Communications Commission. To ensure proper operation, please follow the guidelines provided.

Radiation Exposure

The equipment meets FCC Radiation exposure limits for uncontrolled environments. It is important to maintain a minimum distance of 20cm between the radiator and your body during installation and operation to adhere to safety standards.

Frequently Asked Questions

Q: What should I do if the equipment causes interference?

A: If the device causes harmful interference, try to reposition it or adjust its settings. Ensure that it is not placed near other electronic devices that may be causing interference.

Q: Can I operate the equipment closer than 20cm to my body?

A: To comply with FCC regulations and ensure your safety, it is recommended to maintain a minimum distance of 20cm between the radiator of the equipment and your body at all times.

Please read this manual carefully and keep it properly before using the product. Illustrations of products, accessories, user interfaces, etc, in the manual, are for reference only. Due to product updates and upgrades, there may be slight differences between the actual product and the illustrations; please refer to the actual product. Before powering on, please remove all protective films.

Safety Notes

1. After the printer is turned on, the extruder temperature will reach around 2oo·c.
   Please avoid contact with any part of the body to prevent burns.

2. Please use the provided power adapter and unplug the device’s power plug if not in use for an extended period.

Product Introduction

Tool list

Diagonal cutter X1
Used for removing supports.

Tips: The ” ” icon next to the t it le indicates that there is a detailed instructional video in the Artist app. Please select Home> Top-left icon> Printing Tutorial in the app.

Installation

Remove the foam
Remove the two pieces of foam inside the machine separately.

Install the guide tube
Inside the print chamber, there is a white guide tube.
Extend the guide tube from the long rectangular space at the top of the machine, and insert it into the circular extruder hole at the back of the machine, pushing it all the way in.

Connect Power
Connect one end of the power cord to the printer and plug the other end into the power out let.

App Installation and Pairing

1. Download the app from the app store or Google Play, and follow the app’s instructions to complete the registration.

2. Ensure that the Bluetooth on your phone or tablet is turned on.

3. Click the icon in the upper left corner and select Add Printer.

4. In the powered-off state, press and hold the power button for 8 seconds to enter
   pairing mode. Release your finger after hearing the voice prompt indicating that
   the device has entered the pairing mode.

5. Follow the app’s instructions to enter the Wi-Fi selection page, choose the Wi-Fi network to connect to, and enter the Wi-Fi password. (Note: Only supports connecting to Wi-Fi networks in the 2.4GHz frequency band).

6. The printer’s indicator light stays solid white, indicating a successful pairing.

Tips: If pairing fails, please check:

1. Whether the Wi-Fi password is correct.
2. Whether Wi-Fi is connected to the internet
3. Whether Bluetooth on mobile devices such as phones and tablets is turned on.

Install Filament Spool
Note: Be sure to use the official filament spool for printing; otherwise, it may not guarantee the success rate and print quality, and it may even damage the printer.
Do not touch the extruder with your hands.

1. Use the Artist app to scan the QR code on the filament spool; scan it only once,
2. Click on the top-left icon, go to My Printer> Filament Replacement> Installation.
3. First, cut off the bent part of the filament line with the diagonal cutter, then insert it into the entrance of the guide tube beneath the extruder (refer to the diagram on page 2). The printer will automatically retract the filament, and when the filament is automatically fed in, it indicates that this step is successful.
4. Wait for the extruder head to heat up; a small amount of filament will be extruded. Do not touch the extruder head with your fingers. Use a diagonal cutter to cut off the extruded filament from below the nozzle. (Be careful not to touch the nozzle with the diagonal cutter).
   Note: For detailed operational procedures, please refer to the printing tutorial and guidance in the app.

Printing and Model Processing

Notes before Printing

1. Ensure that the magnetic printing bed is placed flat. The inner measurement of the magnetic printing bed should align with the internal raised edge [do not press onto the raised edge), and the surface should be clean. Inhere is any filament remains on the surface of the magnetic printing bed, use a spatula to clean it.
2. There is no residue or foreign objects on the extruder.
3. The room temperature in the space where this product is placed should be maintained between l0″C – 30-C.
4. Close the chamber door to prevent burns from high temperatures and to prevent foreign objects from entering the printer and affecting print quality.

Initiate Printing

1. Select Model
2. Model Library Selection
   Goto the Artist 3D APP homepage, selectthe model you want to print, and click on ‘Retrieve> Print.

2.  **Private Model Printing**  

If you need to print a private model (not available in the app’s model options), click the scan icon at the top of the a pp homepage. Enter the displayed URL in the computer’s web browser address bar and press Enter. The browser will show a QR code page. Scan this QR code with the app to complete the computer login. Follow the computer’s guidance to upload the private model. After uploading, initiate printing in the app.My Printer> Cloud Printing, select the file and print.

3.  **Print from a USB Drive**  

If printing a Geode file, copy t he Geode lo a USB drive and insert ii into the 3D printer. Go to My Printer > USB Printing in the app, and choose the file to print

Filament Replacement: My Printer > Filament Replacement> Installation
Tips: During the printing process, if the filament runs out or there is a reminder of insufficient filament, please follow the guidance in the app to replace the filament. When replacing, please be aware that the extruder temperature is high. do not touch it with your hands.

Model Processing
After printing, the model needs support removal and polishing for the ideal finished result

1. Removing the Model: Open the chamber door, take the printed model along with the magnetic printing bed, and bend the magnetic printing bed forcefully to separate the model from it (refer to the diagram for removing the model). After the model is detached from the magnetic printing bed, use a spatula to clean the magnetic printing bed thoroughly [refer to the cleaning diagram for the printing bed), and then reinstall it back into the printer.
2. Support Removal and Polishing: If there are supports, remove them from the model. If there are support remains on the model, use polishing tools.
   Tools: Diagonal cutter(included), polishing tool (self-provided)

Important Reminder

1. Please wear glasses to prevent plastic fragments from entering the eyes.
2. Donat dismantle support structures by hand to avoid injuring your hands. Please use the diagonal cutter.
   Operation: (1) Use the diagonal cutter to separate the supports from the model in an outward- to-inward sequence. If there are support residues on the model, use sandpaper or other polishing tools to smooth and flatten the model surface. Refer to the app’s instructional videos for detailed guidance.

Camera (Pro Version)

Go to My Printer > Camera in the Artist app to view and download images in real-l ime.

Buttons and Indicators

Buttons

Indicator Lights

Usage Notes

• Place the product in a flat, dry, and well-ventilated area, away from flames and heat sources.
• Please use only the provided AC power cord.
• Before moving, disconnect the AC power connection from the power outlet.
• Unplug the device’s power plug if not used for an extended period.
• Do not insert or remove the power plug with wet hands to avoid electric shock or injury.
• Avoid excessive twisting, bending, or twisting of the AC power cord, as this may expose the core or cause it to break.
• If the power cord is damaged, ii must be replaced by the manufacturer, its service department. or qualified professionals to avoid danger
• When disconnecting the power cord, be sure to pull the power plug part by hand, do not pull the AC power cord to prevent electric shock or short circuit.
• Do not upload inappropriate, explicit, or infringing content such as text, videos, models, etc., in the Artist app, or the uploader will be held responsible under relevant laws. Refer to the relevant user agreement in the app for details.

Specification

• Product Name: Artist 3D Printer
• Wireless Connection: Wi-Fi IEEE 802.11b/g/n 2.4GHz
• Compliance Standard: GB 4943.1-2022
• Product Dimensions: 270.5 • 305.9 • 308.5 mm
• Printing Size: 150 • 120• 150 mm
• Package Contents: Main unit, power adapter, user manual, diagonal cutter.
• Product Model: SMYC40
• Rated Input: 24V-2.2A MAX
• CMIIT ID: 2023DP20196
• Quantity: 1 unit

Warranty Information

Warranty Period:

1. Received the product, in case of performance failures listed in the “Product Performance Failure List,” confirmed by the Sen ma Utrend after-sales service center, you can enjoy free return or exchange services
2. Within 15 days from the day you received the product, in case of performance failures listed in the “Product Performance Failure List,” confirmed by the Senma Utrend after-sales service center, you can enjoy f ree exchange or repair services.
3. Within 12 months from the day you received the product, in case of performance failures listed in the “Product Performance Failure List,” confirmed by the Senma Utrend after-sales service center, you can enjoy free repair services.

Warranty Coverage

Product Performance Failure List

Non-Warranty Regulations

1. Unauthorized repairs, misuse, collisions, negligence, abuse, liquid ingress, accidents, modifications, incorrect use of non-original product accessories, tearing, altering labels, and tampering with anti-counterfeiting marks.
2. Beyond the effective warranty period.
3. Damage caused by force majeure.
4. Cases not meeting the performance failures listed in the “Product Performance Failure List.”
5. Performance failures listed in the “Product Performance Failure List” are caused by human factors affecting this product and its accessories. Other considerations

To ensure the safe transportation of the product during shipping, it is recommended to keep the packaging box for 365 days from the date of receipt.

Warranty Card

User Name:
Mailing Address:
Contact Number:
Product Name and Model: ___ _
Product Serial Number: _
Date of Product Purchase: __

• Email: service@lotmaxx.com

• Website: www.en.dafenqi3d.com

• Manufacturer: Shenzhen Senma Utrend Technology Co., Ltd.
  (Xiaomi Ecological Chain Enterprise)

• Address: Floor 2, Building 9, Rundongsheng Industrial Zone, No. 467, Section Xixiang, 107 National Road, Longteng Community, Xixiang Street, Bao’an District, Shenzhen, China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>