fienza FI-K014 Isabella Back Wall Trap Toilet Suite Installation Guide

fienza FI-K014 Isabella Back Wall Trap Toilet Suite

Dimensions

CHECK GOODS THOROUGHLY BEFORE INSTALLATION
Installation of received goods that are damaged, warped or faulty will void warranty. Ensure all items meet your plumbing requirements.

K014

• Rimless
  

• Soft Close
  

Standard Seat

P-Trap • K014P
S-Trap 90-160 • K014A
S-Trap 160-230 • K014B

Slim Seat

P-Trap • K014P-2
S-Trap 90-160 • K014A-2
S-Trap 160-230 • K014B-2

• Rimless hygienic flush
• Short projection for tight spaces
• Gloss white finish
• Large, easy-push chrome flush buttons
• Concealed pan for easy cleaning
• UF quick release, soft close seat
• High quality, R&T flush mechanism
• Top or bottom inlets:
  • Left top inlet
  • Left or right bottom inlet
• Available as P-Trap or S-Trap
• WELS 4 Star rated, 4.SL/3L (3.3L average flush)

Parts List

All installations should be carried out by a qualified tradesman in compliance with the National Plumbing & Drainage Code and any State or Local Authority Regulations, in accordance with AS/NZS 3500 series of standards and AS/NZA 6400. All measurements are in millimeters and are subject to change without notice. For ceramic products, please allow+/- 10 mm tolerance for manufacturing variance. Please refer to fienza.com.au for the latest product specification.

Cistern Installation

1. Parts required to mount cistern to pan.
   

2. Attach cistern bolts into pan. Tighten from underneath.
   

3. Ensure outlet rubber is fitted to cistern.
   

4. Sit cistern onto pan.
   

5. Use supplied bolts to fasten cistern to pan.
   

6. Attached the supplied flexi hose as pictured to suit your inlet setup.
   

S-Trap Installation

1. The 5-pipe should be put into position and cut to suit your set out, then attached to the wall using the thread bolt and plate provided.
2. Now push the pan hard into position to ensure the ceramic outlet is pushed into the 5-pipe by approx 50 mm. This is so the rubber inside the 5-pipe gets a good seal to stop water leaking.

PLEASE DO NOT SILICONE PAN TO FLOOR UNTIL TOILET HAS BEEN CHECKED FOR LEAKS.

Seat Installation

1. Open the box and check all the components.
2. Insert the expansion fittings (5) into the seat bolt holes in the pan.
3. Assemble washers (4), hinge fixings (3) and bolts (2) as shown in the diagram. Leave loosely attached.
4. Align the hinge housing of the seat with the hinge fixings and adjust the seat to desired position.
5. Remove the seat by depressing the chrome release button and lifting upwards.
6. Tighten the bolts with a Phillips head screwdriver ensuring that the expansion fittings are secure. Put the decorative cap in the position then attach the seat on the hinges.
   

All installations should be carried out by a qualified tradesman in compliance with the National Plumbing & Drainage Code and any State or Local Authority Regulations, in accordance with AS/NZS 3500 series of standards and AS/NZA 6400. All measurements are in millimeters and are subject to change without notice. For ceramic products, please allow+/- 10 mm tolerance for manufacturing variance. Please refer to fienza.com.au for the latest product specification.

Inlet Valve Service

WARNING
Do not use chlorine/chemical sanitisers in the cistern tank. Such use may result in damage to tank components and will void the product warranty.

1. Water Level Adjustment
   

2. Cleaning the Diaphragm
   It is possible for dirt/debris to prevent the valve shutting off. To remedy this the diaphragm may be cleaned as follows:

3. Unclip the float arm from the adjustment screw

4. Twist the plastic top-assembly firmly anti-clockwise and remove it from the valve body

5. Inspect both rubber diaphragm and valve seat

6. Rinse under running water to remove debris

7. Re-assemble in reverse order
   

Outlet Valve Service

• Removal
  Valve may be removed for service – twist to unlock
  

• Assembly
  Hoses are not shown on the diagram
  

• Push Button Rod Settings
  Button rods must be just clear of the valve pads.
  Button rods can be adjusted by screwing up or down.
  

• Ensure that buttons match valve pads
  

• Half Flush Adjustment
  Half flush volume can be adjusted by moving the side float up or down. Moving the float DOWN increases the flush. Moving the float UP decreases the flush.
  

• Full Flush Adjustment
  Full flush volume can be adjusted by changing the residual water level in the cistern. Move the adjuster DOWN to increase the volume. Move the adjuster UP to decrease the volume.
  
  

All installations should be carried out by a qualified tradesman in compliance with the National Plumbing & Drainage Code and any State or Local Authority Regulations, in accordance with AS/NZS 3500 series of standards and AS/NZA 6400. All measurements are in millimeters and are subject to change without notice. For ceramic products, please allow+/- 10 mm tolerance for manufacturing variance. Please refer to fienza.com.au for the latest product specification.

Warranties

Residential Warranty Periods

Applies to domestic uses and applications of Fienza® products, such as private dwellings and retirement villages.

TOILETS ‘

Range| Residential
Vitreous China| 5 year s replacement parts or product,
1 year labour
R&T Cisterns (Tanks & Frames)| 5 years replacement parts or product,
1 year labour
R&T Cisterns (Valves)| 3 years replacement parts or product, 1 year labour
Accessories & Spare Parts| 1 year replacement parts or product

• Excludes parts subject to wear and tear such as rubber seals. Labour is not included unless otherwise specified.

Commercial Warranty Periods

Applies to commercial uses and applications of Fienza® products, including, but not limited to: commercial food premises such as restaurants; commercial accommodation such as hotels; hospitals and healthcare facilities; public amenities; and industrial, laboratory and manufacturing facilities.

TOILETS ‘

Range| Commercial
Vitreous China| 3 years replacement parts or product, 1 year labour
R&T Cisterns (Tanks & Frames)| 5 years replacement parts or product,
1 year labour
R&T Cisterns (Valves)| 1 year replacement parts or product,
1 year labour
Accessories & Spa re Parts| 1 year replacement parts or product

• Excludes parts subject to wear and tear such as rubber seals. Labour is not included unless otherwise specified.

Australian Consumer Law

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Fienza Pty Ltd reserves the right to make changes in product characteristics, packaging or availability at any time without notice. Please visit fienza.com.au for the latest information.

Warranty Conditions

• Installation has been carried out by a licensed tradesperson in accordance with all applicable Building, Plumbing and Electrical codes, and Federal, State, or Local Government Regulations in accordance with AS/NZS 3500 Plumbing & Drainage, AS/NZS 6400 Water Efficient Products, and AS/NZS 3000 Electrical standards for any installations to which these standards apply.
• All maintenance and adjustments to the product after the installation have been carried out by a licensed tradesperson. All care and cleaning instructions have been adhered to as prescribed.
• All goods of substandard quality manufacture (excluding imperfections permitted within AS1976 – Vitreous China used in Sanitary Applications) will be credited or replaced by Fienza when advised within the warranty period, subject to prior inspection and agreement.
• Proof of purchase is required for warranty claims.

Warranty Limitations

To the extent permitted under the Trade Practices Act and other relevant legislation, Fienza’s liability is limited to:

• The cost of replacing the goods, or
• The cost of obtaining equivalent goods, or
• The cost of having the goods repaired
• Fienza is not responsible for any lack of operation or performance of goods (or any loss or damage) where goods are used or adapted for a with other goods not supplied by Fienza.
• It is the responsibility of the customer and installer before installation to ensure are correct and free of obvious visible faults.
• Fienza is not responsible for the labour and rectification costs incurred in the above circumstance.

Conditions for On-Site Warranty Service Calls

Fienza will charge a service fee for each visit to an installation by its technician where it is determined that the fault is due to poorly executed or unlicensed installation work or where the product is not a genuine Fienza product or where the product is outside the warranty period. This may be paid in advance by credit card over the phone to a Fienza technician attending the site and will be refunded if the Fienza product is found to be at fault.

Cleaning & Operation

• The toilet seat may be removed for cleaning – depress the chrome hinge release buttons and lift up.
• Clean only with a soft cloth or sponge using warm water and mild soap or detergent. Do not use any abrasive cleaning materials.
• Do not use any solvents or corrosive liquids.
• Note that use of clip-on deodorisers will affect flushing performance on rimless suites.

All installations should be carried out by a qualified tradesman in compliance with the National Plumbing & Drainage Code and any State or Local Authority Regulations, in accordance with AS/NZS 3500 series of standards and AS/NZA 6400. All measurements are in millimeters and are subject to change without notice. For ceramic products, please allow+/- 10 mm tolerance for manufacturing variance. Please refer to fienza.com.au for the latest product specification.

CUSTOMERS SUPPORT

For warranty support, please contact Fienza
15 Walter Cres, Lawnton OLD 4501
PO Box 5381, Brendale OLD 4500
P 07 3490 6700 F 07 3490 6719
E help@fienza.com.au
ABN 76 136 411 311

FIENXA.COM.AU
!SABELLA
Item Code: K014
Updated: 09/08/2023

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>