fienza FI-FMR60 Empire Framed Mirror Installation Guide

INSTALLATION GUIDE

FI-FMR60 Empire Framed Mirror

Mirrors,
Glue-On Installation
Mirrors,
With Mounting Brackets
CHECK GOODS THOROUGHLY BEFORE INSTALLATION
Installation of received goods that are damaged, warped or faulty willvoid warranty. Ensure al items meet your requirements.

Glue-On Installation

Required Tools
1x Double Sided Tape Roll
1 x Waterproof/Wet Area
Bathroom & Kitchen Silicone
4x Paddle Pop Stick

1. Make sure all walls are painted if using double sided tape. Note: Double sided tape does not stick to unpainted walls.

2. Stick a length of double-sided tape (roughly 70-90mm) depending on the size of your mirror near each corner.

3. Apply multiple and generous dobs of waterproof/ wet area bathroom and kitchen silicone to the wall roughly 35mm diameter.
   NOTE: Not too close to the edge of the mirror as it will spread once you pushed the mirror onto the wall.

4. Place paddle pop sticks or other skinny implement on top of the splashback tiles or benchtop. These paddle pop sticks are used to make sure the glass mirror doesn’t accidently get chipped.

5. Place mirror into position onto the wall. Once the mirror is in position push the glass evenly towards the wall to spread the dobs of silicone long the back.

6. After 2 days, you can remove the paddle pop sticks or other props that were used. Apply silicone around the mirror and underneath to cover the small gap left by the props.

Mounting Bracket Installation

IMPORTANT:
To avoid any mistakes, before drilling any holes into the wall, turn the mirror over and measure the distance between the bracket holes to ensure the correct mirror placement.

Required Tools
Drill with 6-8mm Drill Bit
Tape Measure
Phillips-head Screwdriver
Hammer
pencil
Level

Rectangle, Square or Arch Wall Mirrors

1. Measure and mark the desired height for your mirror on the wall with a pencil. Use a measuring tape to ensure that the marks are even and level.

2. Drill pilot holes for the wall anchors where you have marked the location of the mounting screws.
   Use a drill bit that is slightly smaller than the size of the wall anchors (between 6-8mm).

3. Insert the wall anchors into the pilot holes.
   Tap them gently with a hammer until they are flush with the wall. Screw the mounting screws into the wall anchors.

4. Hang up the mirror using the brackets provided on the back of the mirror.

Round or Oval Wall Mirrors

1. Measure and mark the desired height for your mirror on the wall will a pencil. Use a measuring tape to ensure that the marks are even and level.

2. Dill pilot holes for the wall anchors where you have marked the location of the mounting screws.
   Use a drill bit that is slightly smaller than the size of the wall anchors (between 6-8mm).

3. Insert the wall anchors.

4. Screw the mounting screws into the wall anchors.

5. Line the mirror up with the mounting screws.

6. Hang up the mirror using the brackets provided on the back of the mirror.

Cleaning & Care

For best results, clean mirrors with a combination of 30% methylated spirits to 70% water and a soft, non-abrasive cloth designed for use on glass surfaces.

Warranties

Residential Warranty Periods
Applies to domestic uses and applications of Fienza® products, such as private dwellings and retirement villages.
Commercial Warranty Periods
Applies to commercial uses and applications of Fienza® products, including, but not limited to: commercial food premises such as restaurants; commercial accommodation such as hotels; hospitals and healthcare facilities and manufacturing facilities; ; public amenities; and industrial, laboratory

replacement parts or product
Australian Made Mirrors| 1 year replacement parts or product| 1 year replacement parts or product
Spare Parts| 1 year replacement parts or product| 1 year replacement parts or product

Australian Consumer Law
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Fienza Pty Ltd reserves the right to make changes in product characteristics, packaging or availability at any time without notice. Please visit www.fienza.com.au for the latest information.
Warranty Conditions

• Installation has been carried out by alicensed tradesperson in accordance with all applicable Building, Plumbing and Electrical codes, and Federal, State, or Local Government Regulations in accordance with AS/NZS 3500 Plumbing & Drainage, AS/NZS 6400 Water Efficient Products, and AS/NZS 3000 Electrical standards for any installations to which these standards apply.
• All maintenance and adjustments to the product after the installation have been carried out by a licensed tradesperson.
• All care and cleaning instructions have been adhered to as prescribed.
• All goods of substandard quality manufacture (excluding imperfections permitted within AS1976 – Vitreous China used in Sanitary Applications) will be credited or replaced by Fienza when advised within the warranty period, subject to prior inspection and agreement.
• Proof of purchase is required for warranty claims.

Warranty Limitations
To the extent permitted under the Trade Practices Act and other relevant legislation, Fienza’s liability is limited to:

• The cost of replacing the goods, or
• The cost of obtaining equivalent goods, or
• The cost of having the goods repaired.
• Fienza s not responsible for any lack of operation or performance of goods (or any loss or damage) where goods are used or adapted for use with other goods not supplied by Fienza.
• It is the responsibility of the customer and installer before installation to ensure that all components are correct and free of obvious visible faults.
• Fienza is not responsible for the labour and rectification costs incurred in the above circumstance.

Conditions for On-Site Warranty Service Calls
Fienza will charge a service fee for each visit to an installation by its technician where it is determined that the fault is due to poorly executed or unlicensed installation work or where the product is not a genuine Fienza product or where the product is outside the warranty period. This may be paid in advance by credit card over the phone to a Fienza technician attending the site and will be refunded if the Fienza product is found to be at fault.

For warranty support, please contact Fienza
2 Bailey Court, Brendale QLD 4500 PO Box 5381, Brendale QLD 4500
P 0734906700 F 0734906719 E help@fienza.com.au ABN 76 136 411 311

Allinstallations must be carried out by a licensed tradesperson in accordance with all applicable Building, Plumbing and Electrical codes, and Federal, State, or Local Government Regulations in accordance with AS/NZS 3500 Plumbing & Drainage, AS/NZS 6400:2016 Water Efficient Products, and AS/NZS 3000:2007 Electrical standards for any installations to which these standards apply

FIENZA.COM.AU
MIRRORS
Updated: 01/05/2023

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>