MOVE SA-0045 Wireless Hybrid Remote and Charging Cradle Instructions

TOOLS

• Fine-tip Marker
• Electric Drill
• 7/32″ Drill Bit
• 7/64″ Drill Bit

• 2 Phillips-Head Bit

INCLUDED HARDWARE

DRILL MOUNTING HOLES

Check the area beneath where the Charging Cradle will be mounted to ensure there are no hoses, wires, lines, tanks or other sensitive components.

STEP 1 Choose a flat surface with adequate space to mount the Charging Cradle B .
STEP 2 Lay mounting template in place, mark and drill routing hole for power wire using a 7/32″ Drill Bit.
STEP 3 Mark and Drill mounting holes for Screws C using a 7/64″ Drill Bit.
IMPORTANT! If installing to gel-coat, follow the drilling procedure in Appendix A of the Installation & Owner’s Guide to ensure you do not crack or chip the gel-coat.

INSTALL CHARGING CRADLE

Using a #2 Phillips Head Screwdriver, install (2) #8 x 1/2″ Screws C and tighten snug.

CONNECT TO POWER

NOTICE: Follow Appendix B of the Installation & Owner’s Guide for proper ring terminal and butt connector installation procedures.
STEP 1 Route wire to power.
STEP 2 Attach the Fuse Holder G to the Positive (+) lead from the Charging Cradle B using Butt Connector F .
STEP 3 Depending on post size, attach the appropriate Ring Terminals D or E and connect to power, connecting the Positive (+) lead to the positive post and Negative (-) lead to the negative post.

NOTICE: All Move accessories are compatible with 12v, 24v, and 36v systems.

PAIRING TO THE MOVE

PAIRING TO POWER-POLE SHALLOW WATER ANCHORS

PAIRING POWER-POLE MICRO ANCHORS

(Only for Micro Achors with CM2 Control system)
STEP 1 Press and hold the PROGRAM LED turns steady GREEN. button on the HPU or Micro Driver Unit until 3 seconds until the
STEP 2 Press the Anchor Up and Anchor Down buttons on the Hybrid Remote at the same time for one second. When paired, the GREEN LED will flash steadily.
IF PAIRING TO DUAL MICRO ANCHORS Repeat STEPS 1 & 2 with the other Micro Driver Unit.

REMOTE FEATURES OVERVIEW

Remote Battery Level Indicator
Remote Control LED
The Remote Control LED serves as a battery level indicator for the Remote Control. When a button is pressed, the LED will flash either red, yellow or green, depending on the battery level (red being low, green being charged).
Charging the Wireless Hybrid Remote
The Remote Control snaps into the Charging Cradle. It can be stored in the dock or removed and used. To remove the remote, grab either side and firmly pull it from the cradle.
While charging, the LED on the remote will flash red if the battery is low, yellow at mid-charge, green when nearing full charge, and will shift to a solid green when fully charged.

Charging Temperature Constraints
To avoid damage, the Remote Control will not be charged in extreme hot or cold temperatures. If the remote LED displays solid red, it is over charging temperature (113°F). If it displays solid blue, it is too cold for charging (32°F).

Firmware Updates
If a firmware update is available, the next time the Remote Control is plugged into the dock it will be downloaded. While the update is downloading to the remote, the LED will slowly blink red. While the update is installing to the remote, the LED will flash red and green intermittently. When the update is installed, the LED will turn off.

REMOTE BUTTON FUNCTIONS

9010 Palm River Road, Tampa, Florida 33619 · phone 813.689.9932 · fax 813.689.8883 · power-pole.com Power-Pole is a registered trademark of JL Marine Systems, Inc. © Copyright 2023 JL Marine Systems, Inc. All Rights Reserved.

References

• Power-Pole Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>