apart CM20DTS Audio 4.25″ 100V Line Ceiling Speakers User Manual

User Manual

CM20DTS / CM30DTD / CM60DTD
Instruction manual

CM20DTS Audio 4.25″ 100V Line Ceiling Speakers

CM20DTS / CM30DTD / CM60DTD manual

Important safety instructions

Please read carefully before proceeding and keep this manual for future reference. Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short- circuiting, damages, fire, or other hazards. These precautions include, but are not limited to, the following:

• Read these instructions.
•  Keep these instructions.
•  Heed all warnings.
•  Follow all instructions, particularly those pertaining to rigging, mounting, hanging, and electrical connections.
• This professional device needs to be installed by qualified personnel only. As improper installation may cause the unit to fall, resulting in personal injury and/or property damage.
• Take care of the loudspeaker wires; they should be free of damage. Damaged loudspeaker wires may result in poor sound quality, damaged amplifiers, injury, and/or electrical shock.
•  No mains power shall be connected to the loudspeaker, doing so will damage the loudspeaker, and increase the risk of fire.
•  Respect power rating, to prevent damaged loudspeakers, and risk of fire.
• Do not open the loudspeaker or attempt to disassemble the internal parts or modify them in any way. If the loudspeaker appears to be malfunctioning (no sound or distorted sound), if you detect smoke or a strange smell coming from the unit, discontinue use immediately and have it inspected by qualified personnel.
• Use cables of the right gauge, especially for long runs or high-power systems.
• Use cables with clear color indication and maintain polarity throughout the whole system.
• Avoid loud feedback from microphones; this can damage your loudspeaker.
• Clean only with a dry cloth.
• Avoid touching the unit’s sharp metal edge to prevent injury.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Only use attachments/accessories that are specified and approved by the manufacturer.
• Install the loudspeaker in a location that can structurally support the weight of the unit and its mounting hardware.
• Tighten all speaker clamps securely. Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.
• Do not hold the tweeter as a handle to carry the unit; this can damage your loudspeaker.
• Always attach a safety cable to both seismic safety tabs to secure the loudspeaker to the building structure. Please, be guided by applicable building codes here. Otherwise,  the unit could fall down, resulting in personal injury or even death.
• Use only industry-accepted mounting tools and methods.
• Exposure to loud audio levels over a long time can cause severe hearing loss.
• Do not forget to consult the local law directions regarding producing sound in public places.
• Please check the unit’s condition after unpacking. If the outside or the carton box has been damaged, inform your shipper immediately.
• Do not expose the device to water, damp or wet conditions.
• The unit is designed for fixed installations in buildings. It is not fit for use in mobile applications.
• Refer all servicing to qualified personnel.
• Indoor use only.

The warranty of this product and the applicable terms and conditions are provided by the dealer where you purchased this product.

Introduction

The CM Design Back Can Series loudspeakers have a sealed back can and bass reflex port which gives a controlled sound performance in any kind of ceiling structure. The ultra-slim housing with minimal built-in depth has been tuned to optimize bass and midrange performance while maintaining sonic consistency. The matching Apart sound image allows you to combine various models in the same room or area. All models have a tool-free rotatable 16 ohm and 70/100-volt power selector on the front. The thin-edge grille and integrated neodymium grille fixing magnets guarantee easy, smooth and elegant integration in any kind of environment. With the ease of installation, dynamic sound, pristine clarity, and attractive aesthetics, the CM Design Back Can Series range is the clear choice for installers seeking a reliable loudspeaker with high build quality at affordable prices.

Features

• Design a ceiling loudspeaker with a back can for controlled sound performance in any kind of ceiling structure
• Matching Apart sound image allows you to combine various models in the same room or area
• Tuned bass reflex port for optimized low-frequency performance
• High intelligibility while remaining perfect music reproduction quality
• 4.25” LF driver for CM20DTS and CM30DTD, both with 1” tweeter
• 6.5” LF driver for CM60DTD, with 1” tweeter
• 60 W dynamic power handling for CM20DTS, 80 W for CM30DTD, and 120 W for CM60DTD
• Thin-edge loudspeaker grille for elegant integration
• User-friendly grille mounting due to integrated strong neodymium magnets
• Easily paintable in any RAL color
• Installer-friendly grille safety wire speeds up installation and avoids the grille from falling down during and after installation
• Included tile bridge support rails to prevent ceiling tile from sagging
• Quick installation with two fast screwing loudspeaker clamps
• Minimal built-in depth with uncompromised acoustical performance
• Loudspeaker overload protection for a 24/7 failsafe operation
• Front panel selection of 16 ohms or 100V/70V operation, allows easy and fast adjustment of the loudspeaker power without the need to remove it from the ceiling or  move connection wires
• Enhanced cable management with incorporated strain relief and cable guidance along with provision for a cable gland
• In & Link connection with permanent pass-through on the euro block connector allows easy daisy chaining of multiple loudspeakers
• Two integrated seismic safety tabs allow for the connection of safety cables

Supplied items

Unpack the contents and confirm following items are included.

• Loudspeaker x 2
• Thin-edge grille x 2
• Tile rail x 4
• Tile rail spacer x 4
• Cutout template x 2
• Important safety instructions x 1
  Loudspeaker wires and safety cables are not included.

Installation instructions

ATTENTION
Apart from Audio NV is not responsible for damages resulting from the negligent installation of any loudspeaker.
WARNING
Please make sure that the mounting structure is capable of safely supporting the loudspeaker’s weight.

1. Use the cutout template to mark the mounting hole.

2. When making the hole in your mounting panel, double-check that there are no cables or any other obstructions behind the mounting panel. Cutting the mounting panel without this check might result in damaged infrastructure or power lines.

3. Insert the two tile rails through the cut hole and place them on the ceiling surface right next to the opening. Insert the tile rail spacers in the hole and clip them on the tile rails.

4. Open the connection box on the back of the loudspeaker and take out the euro block connector. Pull the loudspeaker wires through the mounting hole and connect them to the euro block terminal.
   The use of wire ferrules is strongly recommended when the stranded wire is used.

5. Remove the grille from the loudspeaker. The grille is connected to the loudspeaker frame with a detachable wire. This enables the installer to install the loudspeaker more easily without walking up and down the stairs multiple times. It also serves as a grille safety restraint.

6. Turn the mounting clamps inwards (a) and tighten the screws slightly to make them stay in the inward position (b).

7. Insert the euro block connector in the connection box on the back of the loudspeaker and close the cover. This cover acts as a strain relief plate for the cable and a retainer for the euro block connector. If the installation requires the use of a cable gland, use the knockout of 22mm (0.87 inches) present on the cover.
   WARNING Only use a non-conductive cable gland

8. Insert the loudspeaker into the pre-cut hole and fasten the mounting clamp screws carefully until the loudspeaker sits safely in place. Do not overtighten the mounting clamp screws and make sure the clamps are aligned with the tile rails.

9. Always attach a safety cable to one or both provided seismic safety tabs to secure the back can to the building structure. Please be guided by applicable building regulations in this matter otherwise the unit could fall, resulting in personal injury or even death.
   If the safety cable is too long and the loudspeaker should fall the safety cable may snap as a result of too much strain. We, therefore, recommend installing the safety cable with as little slack as possible.

10.  Set the power selector on the front of the loudspeaker in the required position. This power selector switch makes it very easy and fast to balance an installation since there is no need to remove the loudspeakers from their support panel and move wires to different terminals.
    WARNING
    Set the power tapping prior to applying audio and only change the setting while the audio amplifier is shut off.
    WARNING
    The 16-ohm setting is not compatible with 70-volt or 100-volt line amplifiers!
    WARNING
    The highest 70-volt power setting is not compatible with 100-volt line amplifiers, only with 70-volt line amplifiers.

11. Install the thin-edge grille on the loudspeaker. The grille is held in place by powerful magnets. Out of the box, the loudspeaker’s color is pure white (RAL9010). This white finish complements most decors and does not require further painting.
    However, if the interior design requires a custom loudspeaker finish, these loudspeakers are very easy to paint. Only the speaker grille and trim ring have to be painted. For more information, we refer you to the dealer where you purchased this product.

Dimensions – CM20DTS

Dimensions – CM30DTD

Dimensions – CM60DTD

Dimensions – tile rail and tile rail spacer

| mm| inch
---|---|---
A| 627 ± 5| 24.685 ± 0,197
B| 594| 23.385
C  (CM20DTS / CM30DTD)| 190| 7.480
C (CM60DTD)| 228| 8.976

Specifications

60 – 30 – 15 – 7.5 watts
70V transfo power taps| 20 – 10 – 5 – 2.5 – 1.25 watts| 30 – 15 – 7.5 – 3.75 – 1.75 watts| 60 – 30 – 15 – 7.5 – 3.75 watts
connector wire capacity (connection and pass-through)| max. wire size: 2.5 mm² (12 AWG)
frequency range| 80 – 20,000 Hz| 75 – 20,000 Hz| 65 – 20,000 Hz
low impedance dynamic power| 60 watts| 80 watts| 120 watts
RMS power| 40 watts| 50 watts| 60 watts
SPL at 1 W / 1 m| 88| 88| 91
max SPL at 1m| 104| 108| 110
dispersion angle (1000 Hz)| 180°
protection system| self-resetting loudspeaker protection system
---|---
IP rating| indoor use only
mounting system| 2 screws
baffle material| ABS plastic
enclosure material| steel
grille material| steel
nearest RAL color code, the color deviation can occur| RAL9010 (white)
net weight| 2.05 kg
4.52 lbs| 2.5 kg
5.51 lbs| 4.01 kg
8.84 lbs
outside diameter| 223 mm
8.780 inch| 223 mm
8.780 inch| 258 mm
10.157 inch
depth| 84 mm
3.307 inch| 131 mm
5.157 inch| 157 mm
6.181 inch
cutout diameter| 193 mm
7.598 inch| 193 mm
7.598 inch| 232 mm
9.134 inch
installation grip range| 3 – 41 mm
0.118 – 1.614 inch| 3 – 65 mm
0.118 – 2.559 inch| 3 – 65 mm
0.118 – 2.559 inch

Notes ————–

developed
by
Apart Audio NV
Industriepark Brechtsebaan 8 bus 1
2900 Schoten – Belgium
Company names, product names, and trademarks are the property of their respective owners.
Apart from Audio specifications are subject to change without notice.
https://tm.by

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>