ideal lux AP3 Pashà Wall Lamp Instruction Manual

ideal lux AP3 Pashà Wall Lamp

Product Information

Specifications

• Model: G9
• Max Power: 3 x 40W
• Input Voltage: 220-240V
• Frequency: 50/60Hz
• Product Codes: 8021696082264 (CROMO), 8021696082288 (ORO)
• Energy Efficiency Class: F
• EAN: 8021696209043

Product Usage Instructions

1. Ensure the lighting fitting is installed by a qualified electrician.
2. Follow the assembly instructions by reading the numerical progression provided.
3. This product is equipped with a light source that is replaceable by the end-user.
4. Avoid looking directly at the light source.
5. Always disconnect from the power supply before installation or maintenance.
6. Use appropriate fixing accessories and comply with regulations for replacements.

Safety Instructions

• Ensure compliance with European safety standards EN 60 598-1.
• For damaged external cables, replacement should be done by the manufacturer, retailer, or qualified electrician.
• Always disconnect from the power supply before any installation or maintenance.
• Use suitable fixing materials and follow specific requirements for replacements.

Additional Information

• This product contains LED light sources that are not user-replaceable. Do not dismantle the LED components.
• If the lamp does not turn on, replace the fuse if necessary.
• Class I electrical safety is ensured by primary insulation and a protective conductor.

Contact Information

• Manufacturer: IDEAL LUX s.r.l. Italy
• Website: www.ideal-lux.com

FAQ (Frequently Asked Questions)

• Q: Can the LED light sources be replaced by the end-user?
  A: No, the LED light sources in this product are not user-replaceable and should not be dismantled.

• Q: What should I do if the lamp does not turn on?
  A: If the lamp does not turn on, check and replace the fuse if needed.

Instructions

Wall lamp
G9 max 3 x 40W / 220~240V 50/60Hz

• 8021696082264 CROMO

• 8021696082288 ORO
  

• FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION

• THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

• THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

Installation

This product is provided with a light source with efficiency energy class of:

• Energy Efficiency Class
• 8021696209043 F

LEGENDA ICONE

• Replaceable light source by an end-user.
• Replaceable LED light source by an end-user.
• Replaceable light source by authorized personnel only.
• Non-replaceable light source.
• Upon end of life of the light source, the whole product will be replaced.
• Replaceable control gear by an end-user.
• Replaceable light source by authorized personnel only.
• Upon end of life of the control gear, the whole product will be replaced.

SAFETY INSTRUCTIONS

1. This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
23. Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Totally protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com

IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>