OZARKE BLACKREMOTE Minimalist LED Table Lamp Instruction Manual

OZARKE BLACKREMOTE Minimalist LED Table Lamp

Specifications:

• Power Supply Range: 100-240V, 50Hz
• Indoor Use Only
• Do Not Install Outdoors or in Wet Conditions
• Do Not Expose to Corrosive Chemicals or Gases

Installation Instructions

1. Unbox the contents and ensure you have the lamp, one leg attached via wire, one separate leg, and a tool bag.
2. Attach the separate leg to the lamp body as shown in Figure 1.
3. Securely fasten two screws into the designated holes on the leg to prevent instability.
4. Gently pull the cable taut to fit the attached leg into the connection on the lamp body.
5. Tighten two screws into the holes on the leg as illustrated in Figure 3.

Remote Control Instructions:

1. Install two AAA batteries in the remote. Point it at the light fixture and press the On button to turn on the light.
2. To connect the remote to the lamp, press the On button within 3 seconds after powering the fixture on until it flashes.
3. Adjust brightness using the + and – buttons on the remote.
4. Adjust color temperature using the k+ and k- buttons on the remote.

FAQ:

• Q: Can I install the lamp outdoors?
  A: No, the lamp is designed for indoor use only. Avoid installing it outdoors or in wet conditions.

• Q: How do I adjust the brightness and color temperature using the remote control?
  A: Use the + and – buttons to adjust brightness and the k+ and k- buttons to adjust color temperature. Increasing k+ makes the color cold, while decreasing k- makes it warm.

• Q: What should I do if my remote control does not connect to the lamp?
  A: Make sure you have installed fresh batteries in the remote. Follow the steps to connect the remote within 3 seconds after powering on the fixture.

INSTRUCTION MANUAL
Thank you for shopping with Ozarké, we really appreciate your business. Our goal is to provide an excellent customer service before, during and after delivery. We’ve included a guide on how to install this light, should you require additional assistance please feel free to email us at info@ozarke.com and one of our customer service reps will reach out to assist you.

Before you get started

When working with electrical wiring, follow these safety instructions to prevent injury or damage:

1. Turn off the power: Before starting any work, turn off the power to the area you will be working in.
2. Use appropriate tools: Only use tools designed for electrical work and in good condition.
3. Wear protective gear: Wear safety glasses, gloves, and other protective gear as necessary.
4. Test for power: Use a non-contact voltage tester to check for electrical current before touching any wires.
5. Avoid wet conditions: Do not work with electrical wiring in wet or damp conditions.
6. Keep a safe distance: Stay away from exposed wires or electrical components.
7. Seek professional help: Consult a qualified electrician if you are unsure about any aspect of electrical wiring or encounter any problems.

WARNING!

1. Do not use the power supply beyond the specified range (100-240V,50Hz).
2. Avoid scratching the surface and wires of the lamp during installation.
3. Do not install the lamp outdoors.
4. The lamp should not be close to corrosive chemical objects or gases.
   It should not be washed with water. It can only be wiped with a clean soft cloth.

Installation Instructions

1. Unbox the contents. Ensure that you have the following items:
2. Lamp with one leg already attached via the wire.
3. One separate leg.
4. Tool bag.
5. Attach the separate leg to the lamp body as depicted in Figure 1.
6. Securely fasten two screws into the designated holes on the leg. Ensure a tight connection to prevent potential instability or damage in the future.
7. Gently pull the cable taut, causing the attached leg to snugly fit into the connection on the lamp body.
8. Tighten two screws into the holes on the leg as illustrated in Figure 3.

Remote Control Instructions

1. Please Install two AAA batteries. Once you have installed the batteries, point the remote at the light fixture and press the “On” button the light will come on. The remote should connect automatically once the batteries are installed (If the remote does not connect see step 2)
2. To connect the remote to the lamp, it must be done within the first 3 seconds after you power the fixture on, press the “on “button until the fixture flashes.
3. Once the light is on, use the “+” and “-” buttons on the remote to adjust the brightness. Pressing “+” will increase the brightness, while “-” will decrease it.
4. Once the light is on, use the “k+” and “k-” buttons on the remote to adjust the color temperature. Pressing “k+” will increase the temperature while “k-” will decrease it. Increasing the temperature will make the emitting color cold and decreasing the temperature with make the emitting color warm.

Helpful information

The bottom 5 buttons represent the following:

1. Adjust brightness
2. Dims the light
3. Warm white (4000K) option
4. Warm (3000K) option
5. Cold White (6000K) option

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>