AKASAKATEC SCROVER-02 Smart Construction Rover 2 User Manual

AKASAKATEC SCROVER-02 Smart Construction Rover 2

USER MANUAL

• NSS Receiver ”Smart Construction Rover 2”
• Setting Tool App ”RTFSetting”

What is “Smart Construction Rover 2“ andSetting Tool App “RTFSetting“ ?

• “RTFSetting” Setting Tool App is a dedicated app for setting “Smart Construction Rover 2″.
• This is an Android device-only App.
• This App may not be available on all Android devices.
• “Smart Construction Rover 2” and Android device are set with Bluetooth communication.

“Smart Construction Rover 2” port and Connection cable

“Smart Construction Rover 2” Connection Cable

“Smart Construction Rover 2” : Internal switch (inside battery case ）

“Smart Construction Rover 2“ Setup

**“Smart Construction Rover 2“ : Setting preparation (Set to setting

mode ）**

• Turn off the power of “Smart Construction Rover 2”.
• Open the lid on the back of the main unit and switch the switch in the yellow frame to “ADM”.
• Turn on the power of “Smart Construction Rover2” main unit with a battery or an external power supply.
  *BATT Lump : Green when using batteries, red when using external power supply
• After turning on the power, “Smart Construction Rover 2” starts in the setting mode. (It takes a few minutes to start up.) GNSS lamp is off, WiFilamp is on, and BT lamp is on, and you can access it by the Settings app.

Turn on Bluetooth on Android device

Turn on Android device and turn on Bluetooth. (Ex : Motog7)

“Smart Construction Rover 2” Setting App: Strat “RTFSetting”

Select Receiver to set

“Smart Construction Rover 2“ : Setup

When “Smart Construction Rover 2″ and Android device are connected via Bluetooth, the serial number of the connected receiver will be displayed.

Once connected, the contents of the current receiver settings will be displayed.

Mobile Station System (Rover) : Setting

Reference Station System (Base Station) : Setting

“Smart Construction Rover 2“ : Correction data of the Reference Station

•  When using an external radio with the “Smart Construction Rover 2” Base station, the correction wave to be transmitted is fixed to “RTCM32MSM4”.

*Smart Construction Rover 2 can also be sent with “RTCM32MSM7”, but the amount of data is about 1.7 times that of “RTCM32MSM4”. In order to reduce the transmission data size, please transmit the data with “RTCM32MSM4”.

• Depending on the wireless receiver used at the Base station, the satellite information to be transmitted can onlybe transmitted by GPS + GLONASS or GPS + BEIDOU.
•  If the mobile station GNSS receiver does not support the correction wave “RTCM32MSM4”, RTK will not be inthe “FIX” state.
•  Even if the mobile station receiver supports the correction wave “RTCM32MSM4”, it may not be in the “FIX” state due to specifications such as manufacturer compatibility.
•  Depending on the specifications of the radio used, it may not be possible to send satellite information of the Base station.

Reference Station Mode (Base Station) : Setup

Reference Station Mode (Base Station) : Setup

Reference Station Mode (Base Station) : Setup

“Smart Construction Rover2“ : Return from setting mode to measurement

mode

• Turn off the power of the “Smart Construction Rover 2” main unit.
• Return the switch in the yellow frame on the back of the “Smart Construction Rover 2“ from “Int” to “USR”.
• Turn on the power of “Smart Construction Rover 2” and turn it “ON”.

This completes the Base Station setup procedure.
Please connect to the radio and check the operation.

EU Declaration of Conformity

EARTHBRAIN Ltd.
Izumi Garden Tower, 29fl., 1-6-1 Roppongi, Minato-ku, Tokyo 106-6029 Japan
Tel No +81-3-5797-8034
E-mail info@earthbrain.com

Declaration of Conformity
Hereby, EARTHBRAIN declares that Smart Construction Rover (model#: Smart Construction Rover 2) complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Smart Construction Rover product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, and fulfills the requirements of EN 62368-1:2014/A11:2017.

This SC Rover product(model#: Smart Construction Rover 2) is manufactured by AKASAKATEC INC.
3F. Marina Plaza 4-2, Shiraho, Kanazawa-ku, Yokohama-shi, Kanagawa, 236-0007 Japan
Phone : +81-45-774-3570

FCC Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

RF exposure warning:

The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Specifications:

• Product Name: GNSS Receiver Smart Construction Rover 2 Setting Tool App RTFSetting
• Compatibility: Android devices with Bluetooth communication
• Power Supply: DC12V-24V, External power supply

Frequently Asked Questions (FAQ):

Q: Can I use the RTFSetting Setting Tool App on any Android device?

A: The RTFSetting Setting Tool App is compatible with Android devices that support Bluetooth communication. However, it may not be available on all Android devices.

Q: How long does the battery of Smart Construction Rover 2 last?

A: The continuous operation time when using Eneloop batteries is approximately 4 hours.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>