SUNCO LIGHTING 55682 LED Spec Select Vapor Tight Instruction Manual

SUNCO LIGHTING 55682 LED Spec Select Vapor Tight

Specifications

• Input Voltage: 120-277V
• Color Temperatures: 3500K, 4100K, 5000K
• Dimming: 0-10V IEC Compliant Control
• Wattage Options: Adjustable
• Installation: Surface Mount

Product Usage Instructions

General Wiring Diagram
Ensure to follow the wiring instructions below:

• Black (Line)
• White (Neutral)
• Green (Ground)
• Purple (Dim+)
• Pink (Dim-)
• Yellow (12V AUX)
• Blue (-)
• Red (+)

Field Adjustable Wattage & CCT
Instructions for adjusting color temperature and lumen output:

1. Locate the slide switches on the driver.
2. Select the desired wattage and color temperature by sliding the switches left or right.
3. Each switch position corresponds to different options.

Surface Mount Installation

1. Drill holes for mounting brackets.
2. Secure mounting clips to housing recesses.
3. Release latches and press them into place until secured.
4. Detach the LED tray from the fixture without touching the LED boards.
5. Connect power to the driver as shown.
6. Follow the general wiring diagram and ensure the power supply is disconnected.
7. Reattach the LED tray to the fixture and secure the lens with lens latches.

INSTALL INSTRUCTIONS

PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the luminaire.

WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS

• To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance on this equipment, follow these general precautions.
• Commercial installation, service, and maintenance of luminaires should be performed by a qualified licensed electrician.
• For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
• To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

WARNING: RISK OF FIRE OR ELECTRICAL SHOCK

• Turn off electrical power at the fuse or circuit breaker box before wiring the fixture to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that the supply voltage is correct by comparing it with the luminaire label information.
• All wiring connections should be capped with UL-approved wire connectors.

CAUTION: RISK OF INJURY

• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and discard packing material, as these may be hazardous to children.
• Risk of burn. Disconnect power and allow the fixture to cool before handling the fixture.

NOTICES

• Green ground screw provided in the proper location. DO NOT RELOCATE.
• Use minimum 194°F supply conductors.
• Suitable for Wet Locations.

WARNING – TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER BEFORE INSTALLING

GENERAL WIRING DIAGRAM

Per NEMA rule-change Dim (–) control wires changed from gray to pink after Jan. 01, 2022.
Note: If not connecting to an external 0-10V dimmer circuit, make sure the fixture’s 0-10V pink and purple leads are capped off separately. Failure to do so may cause the fixture to perform incorrectly, and void the warranty.

FIELD ADJUSTABLE WATTAGE & CCT
The end users may adjust the color temperature and lumen output, respectively, by the two slide switches integrated into the driver. Each switch has 3 options (left, middle, and right ), and each position corresponds to 3 color temperatures (3500K, 4100K, and 5000K) and 3 wattages, which can be adjusted to the desired combination.

1. Switches are located on the driver.
2. Select a wattage and color temperature by sliding the switch left or right respectively to the desired value.

WARNING – TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER BEFORE INSTALLING

SURFACE MOUNT INSTALLATION

1. Locate drill holes for mounting brackets. Use hardware found in the hardware kit. Mount bracket to the surface.
2. Secure mounting clips to housing recesses by firmly pressing them into place until both sides of the clip are secured.
3. Release latches by pulling the top of the latch away from the housing.
4. Without touching the LED boards, detach the LED tray from a fixture.
5. Connect power to the driver as shown. (Flexible cord supplied by the installer)
6. Follow the general wiring diagram. Make sure the power supply is disconnected before installing.
7. Reattach the LED tray to the fixture by reversing step 4. 8. Secure the lens to the housing with lens latches.

Note:

• Connect to power using a flexible cord (SJTW 18AWG, not included) to the driver input wires.
• Use the included wet-location-rated strain relief fitting for running the flexible cord through the knockout in the fixture.
• If there are any gaps at the fixture housing after connection, be sure to seal them up with waterproofing silicone glue or sealant
• Specifications subject to change without notice. Photos and line drawings may not be to scale and are for general reference only

FAQ

Q: What should I do if I'm not connecting to an external 0-10V dimmer circuit?

A: Make sure to cap off the fixture's 0-10V pink and purple leads separately to avoid incorrect performance and warranty void.

Q: Can the color temperature and wattage be adjusted after installation?

A: Yes, you can adjust the color temperature and wattage by using the slide switches integrated into the driver.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>