CIARKO DESIGN CDP3803C Cooker Hood Instruction Manual

CIARKO DESIGN CDP3803C Cooker Hood

Product Information

Specifications

• Model: ROTO
• Dimensions: 200 x 44 x 502 mm
• Power: 900W
• Weight: 480g
• Material: Plastic
• Lighting: LED

Product Usage Instructions

Installation

1. Connect the hood as an extractor or recirculation hood.
2. Ensure proper electrical connection.

Maintenance

1. Clean the hood regularly.
2. Replace the grease filter and long-life filter as needed.
3. Check and replace lighting if necessary.

Operation

1. Control the hood using the control panel on the induction hob.
2. Use gestures to adjust speed and functions.

Lighting Adjustment

• Press and hold the designated button to turn the lights on or off.
• Adjust light color and intensity using the remote control.

Timer Function
Set a timer for the hood operation using the remote control.

Frequently Asked Questions (FAQ)

How do I pair the remote control with the hood?
To pair a new remote control, disconnect the hood from power for 15 seconds, then reconnect and press any button on the new remote within 60 seconds to establish the connection.

What do the different LED colors indicate?

• Green: Speed 1
• Blue: Speed 2
• Red: Speed 4 (Boost)

Dear Sirs

• You have become a user of the latest generation of cooker hoods. This hood was designed and manufactured specifically to meet your expectations and will certainly form part of a modern fitted kitchen. Its innovative design and use of modern production technology, ensure its high functionality and aesthetics.
• Please read the following manual carefully before installing the hood. This avoids incorrect installation and operation of the hood.
• We wish you satisfaction and happiness with your choice of the hood of our company.

What’s In The Box

Installations

When installing the device, follow the instructions given in this manual.
The manufacturer shall not be liable for damage resulting from installation not complying with the information contained in the manual. The hood was designed exclusively for domestic use. The hood may vary in appearance from the hood shown in the drawings in this manual, but the recommendations for operation, maintenance, and installation remain unchanged.

• Keep the user manual so that you can refer to it at any time. In the case of selling the device or moving, ensure that the manual is included.
• Carefully read the contents of the operating manual, which provides precise information on the installation, use, and care of the device.
• Do not make any electrical or mechanical changes to the device or the discharging pipes.

Note:
Elements marked with the symbol „(*)” are only included in selected models, in other cases, they should be purchased separately.

Safety Warning

Attention!
Do not connect the device to the mains before installation is complete.

• Before performing any cleaning or maintenance operations, disconnect the hood from the power by removing the plug from the socket or by switching off the main power switch.
• Wear protective gloves for all installation and maintenance work.
• This device is not intended for use by persons (including children) with limited physical, sensory, or mental abilities, and lacking knowledge or experience in the use of such equipment, unless they are supervised or instructed in the use of this device by a responsible person for their safety. Never use a hood without properly installed filters!
• The hood should NEVER be used as a backrest plane unless this option has been indicated. The room in which the hood is used together with other devices burning gas or other fuel should have adequate ventilation. The air drawn in should not be discharged into a duct used for the discharge of flue gases produced by gas devices or other fuels. It is strictly prohibited to prepare food using an open flame under the hood (flambéing).
• The use of open flames is hazardous to the filters and poses a risk of fire, so this must not be done under any circumstances. Care should be taken during frying to avoid overheating of the oil and subsequent self-ignition. Accessible parts can become very hot if used together with appliances designed for cooking. As far as the necessary technical and security measures regarding the regulations issued by the competent local authorities must be strictly observed.
• The hood should be cleaned frequently, both inside and out (AT LEAST ONCE A MONTH), observing the maintenance instructions given in this manual).
• Failure to comply with the rules for cleaning the hood and replacing and cleaning the filters causes a fire hazard.
• To avoid electric shock, do not use or leave the hood without properly installed bulbs. The manufacturer shall not be held liable for any damages or fires caused by the device resulting from non-compliance with the instructions given in this manual.
• This device is marked by EU Directive 2012/19/EU on waste electrical and electronic equipment (WEEE).
• By ensuring that your device is disposed of correctly, you will contribute to reducing the risk of the product hurting the environment and human health, which could occur if the device is disposed of incorrectly.
• The symbol on the device or packaging indicates that this product cannot be treated as other municipal waste. Return it to the appropriate collection and recycling center for electrical and electronic equipment. Proper disposal and scrapping help to eliminate the adverse effects of scrapped equipment on the environment and health. For details on how this appliance can be recycled, please contact your local town hall, town cleaning service, or the shop where you purchased the product.

Operation

The device can be used as an extractor (vapour extraction to the outside) or an absorber (vapours are filtered and discharged back into the room). Hood models that do not have an extractor fan, function only as an extractor and must be connected to the extraction device (not included). Connection instructions are supplied with the external extractor unit. When the air in the kitchen area is particularly polluted, use the hood set at the highest speed. It is recommended that the hood is put into operation 5 minutes before cooking any food and leaving it on for about 15 minutes after the end of cooking.

Hood operating as an extractor

• Vapours are discharged to the outside through a discharge pipe attached to the connecting flange. The diameter of the discharge pipe must be equal to the diameter of the connecting flange. Attention! The discharge pipe is not supplied with the unit and must be purchased.
• In the horizontal part, the pipe must have a slight upward inclination (about 10°) to facilitate the flow of air to the outside. If the hood is fitted with carbon filters, these must be removed. Connect the hood to the ventilation duct with a discharge pipe of a diameter corresponding to the size of the hood outlet (connecting flange).
• The use of smaller cross-section hoses results in a reduction in suction capacity and a drastic increase in the noise level of the hood.
• The manufacturer therefore bears no responsibility for this condition.
• Use the shortest possible pipe.
• Use a pipe with as few bends as possible (maximum bend angle: 90°).
• Avoid radical changes to the cross-section of the pipe.
• Use a pipe with the smoothest possible inner surface.
• The pipe material must comply with the applicable standards.

The Hood operates as an absorber
A charcoal filter must be installed to use the hood in this version. It can be purchased from the seller. The air drawn in is cleaned of grease and odors before it is returned to the room through the grilles in the upper chimney cover.

Hood installation
The minimum distance between the surface on which vessels are placed on the heating device and the lowest part of the cooker hood shall be not less than 45 cm in the case of electric cookers and not less than 65 cm for gas or mixed-type cookers. If a greater distance is specified in the instructions for installing the gas cooker, adjust to such indications.

Electrical connection

• The mains voltage must correspond to the voltage indicated on the plate on the internal part of the hood. If the hood is equipped with a plug, it must be plugged into a compliant outlet by applicable standards and placed in an easily accessible place, even after the completion of the installation. If the hood is not equipped with a plug (direct connection to the mains) or the plug is not located in an easily accessible place, even after the installation has been completed, use a standardized two-pole switch to allow complete isolation from the mains supply under category III overcurrent conditions, by the installation rules.
• Attention! Before reconnecting the hood circuit to the power supply and checking for the correctness of its operation, you should always make sure that the power cord is correctly installed.
• The hood is equipped with a special power cable.
• If this cable is damaged, it must be ordered from the Department of.

Maintenance

Attention!
Before performing any cleaning or maintenance operations, disconnect the hood from the power supply by removing the plug from the socket or turning off the main power supply.

Cleaning the hood
The hood should be cleaned frequently inside as well as outside (at least with the same frequency, with which the grease filters are cleaned) using a cloth moistened with mild agents. Abrasives should not be used.

DO NOT USE ALCOHOL!

Note:
Failure to comply with the regulations for cleaning the device and changing filters causes a fire hazard. It is therefore advisable to follow the advice given. The manufacturer assumes no responsibility for possible engine damage or fires resulting from noncompliance with the maintenance rules and the aforementioned instructions.

Grease filter
Retains fat particles from cooking. It must be cleaned at least once a month (or when the filter contamination indicator – if Your model the hood has an indicator – it tells you when it needs to be replaced), using a nonaggressive cleaning agent, either manually or in the dishwasher at low temperature and on a short washing cycle. When washing in the dishwasher, the metal grease filter may discolor, but it will not change its characteristic filtering features. To remove the grease filter, pull the spring-loaded handle.

Long-life filter

• The filter should be cleaned regularly. This procedure is recommended every two months.
• It involves washing the filter in hot water with detergent or the dishwasher (full program 65 C). After washing, DO NOT squeeze water out of the filter – this may result in damage to the filter.
• To dry and reactivate the filter, place it in the oven set at 70 C for 15-20 minutes.
• The filter should be replaced once every 2 years or when mechanical damage is visible.
• Long-life filter (*) (can be purchased from your dealer).
• The use of such a filter depends on the model.

Lighting
If the lights do not work, first check that the lights have been properly installed. If the lighting still does not work after this check, please contact the service center.

Control of the hood from the control panel of the induction hob
The cooker hood features “wireless control” and is compatible with induction hobs equipped with a wireless function. Numerous induction hob manufacturers offer models that support the integrated wireless control technology of this cooker hood. For comprehensive details on the wireless control features of the hood, please refer to the user manuals provided by the respective induction hob manufacturers.

Gestures and description of remote control functions

Innovative gesture control system – allows full touchless control of the device with just a hand movement. The cooker hood is extremely intuitive and works according to the 3 gestures so that your extractor hood fulfills its function.

• To switch on the extractor hood, move your hand horizontally from left to right about 3-5 cm below the sensor.
• In this way, the power level changes to a higher gear (2).
• The current power level is indicated by the corresponding LED color displayed on the control panel.
• Power level 1: LED lights up green
• Power level 2: The LED lights up blue
• Power level 3: The LED lights up pink
• Power level 4 / Boost: LED lights up red

On/Off Motor:

• To switch off the hood or change the speed mode to a lower one, pull the hand from the right side to the left (1).
• Press and hold (1) for 2 seconds to turn off the engine.
• Press and hold (2) for 2 seconds to turn on 4th gear.

Boost:

• Power level 4 is a boost function, which means that after
• 5min of operation, the hood automatically reverts to power level 3

LED On/Off:

• To switch the lighting on or off hold down your hand for approx.
• 2 seconds or press the button (3) on the remote control.

Dynamic Light:

• To adjust the light temperature (warm/cold), hold the
• Button (4) or (5) on the remote control pressed.

Light dimming:
To adjust the light intensity, press and hold down the button (3) on the remote control for approx. 2-3 sec. The light dimming can also be adjusted by pressing buttons (4) and (5). Three levels of light intensity are available.

Timer:
To use this function, select a power level (buttons 1 and 2), and then press the Timer button (6). The duration of the timer is 10 minutes. The function is indicated by a blinking LED.

Radio remote control operation:

• The radio remote control pairing mode is activated automatically after a power reset and is active for 60 seconds but is not signaled in any way. During this time, press any key on the remote control. Pressing the key will connect the cooker hood with the radio remote control.
• (If you need a new radio remote control, you will need to reconnect it to the hood).
• Disconnect the hood from the power supply for 15 seconds. Then reconnect the power supply of the hood. Press any button on the new remote control within 60 seconds.
• The hood is now linked to the new radio remote control)

Service Contact

Polska:

• Ciarko Spółka z ograniczoną odpowiedzialnością Sp. K. ul. Okulickiego 10 38-500 Sanok, Polska NIP 6852210122 Serwis gwarancyjny i pogwarancyjny oraz sprzedaż części zamiennych:
• e-mail: serwis@ciarko.pl.
• tel: +48 13 46 53 534
• Österreich: Exklusiver Vertriebspartner der Marke Ciarko Design für Österreich: AXORA GmbH Fürstenstraße 18 4052 Ansfelden Österreich

Garantie und Nachgarantieservice:

• e-mail: support@axora.at
• Tel. 0043 660 3027320
• Slovenská republika: Výhradný distribútor značky Ciarko

Design pre Slovensko:
ELEKTRO STORE SK, s.r.o. Horná 116, 022 01 Čadca, Slovenská republika

Záručný a pozáručný servis:

• tel.: +421 915 473 787
• email: hlaseni.reklamaci@elmax.cz
• Predaj náhradných dielov:
  • tel: +421 915 473 787
  • email: servis@elmax.cz
  • www.ciarkodesign.sk.

Česká republika:
Výhradní distributor značky Ciarko

Design pro Českou republiku:
ELMAX STORE, a.s. Topolová 777/2, 735 42 Těrlicko, Česká republika

Záruční a pozáruční servis:

• tel.: +420 599 529 251
• email: hlaseni.reklamaci@elmax.cz

Prodej náhradních dílů:

• tel: +420 599 529 250
• email: servis@elmax.cz
• www.ciarkodesign.cz.

Republika Hrvatska:
Ekskluzivni prodajni partner marke

Ciarko Design za Republika Hrvatska:
AXORA GmbH Fürstenstrasse 18 4052 Ansfelden Austrija

Jamstveni i postjamstveni servis:

• email: support@axora.at
• Tel 0043 660 3027320

Finland:

• Oy Lapetek Ab, Office: Hermannin Rantatie 2B, B9, 00580 Helsinki, Finland Warehouse: Kankiraudantie 1, 00700 Helsinki, Finland
• Tel. +358 9 2511 030

References

• Hlavní strana | Ciarko Design ÄŒR
• Hlavní strana | Ciarko Design SK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>