Argos 942/4010 Home Fully Framed Bath Screen Instruction Manual

June 9, 2024
Argos

Argos 942/4010 Home Fully Framed Bath Screen Instruction Manual
Argos 942/4010 Home Fully Framed Bath Screen

 Safety and Care Advices

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.

  • Keep children and animals away from the work area, small parts could choke if swallowed.

  • Make sure you have enough space to layout the parts before starting.

  • This product has been constructed to be used in the domestic environment only and not for commercial purposes.

  • Assemble the item as close to its final position (in the same room) as possible.

  • Assemble on a soft level surface to avoid damaging the unit or your floor.
    DRILL

  • We do not recommend the use of power drill/drivers for inserting screws as this could damage the unit. Only use hand screwdrivers.

  • Parts of the assembly will be easier with 2 people.

  • Dispose of all packaging carefully and responsibly.

Care and maintenance

  • Only clean using a damp cloth and mild detergent. Do not use abrasive cleaners
  • Use a dry cloth to clean the product, furniture polish is not recomended.
  • From time to time check that there are no loose screws, nuts or bolts. If there are please re-tighten.
  • This product should not be discarded with household waste. Take to your local authority waste disposal center.

Glue safety – Take care when using glue, please follow the advice below

Skin contact: Remove contamination by washing with soap and water. Procedure should also followed prior to eating and drinking.
Eye contact: Rinse immediately with clean water for 15 minutes and seek medical advice.
If swallowed: Seek medical advice immediately

Additional Guidance

  • Check that the bath has been installed correctly and that it is level, tiled down onto and sealed to the manufacturer’s guidelines.
  • All product supplied without bath.
  • Check that there is sufficient space on the bath for the product and that the screen movement does not foul other items such as sinks and taps.
  • Ensure the product is fitted to a non-porous surface ie. tiled.
  • Check that the wall surface is flat.
  • Unpack and check the product is complete and undamaged.
  • Fixings are supplied for solid walls only. Ensure that the correct fixings are used for the wall type
  • if in doubt seek professional advice
  • Ensure the area is clean, dry and dust free.
  • Read the instructions in full.
  • Have the correct tools available

Fittings (shown to scale)

Fittings \(shown to scale\)

Hardware

Hardware Hardware

Hardware

  • No.8 x 1¾” Pan Head Pozi Screws x 2
    Hardware

  • Wall Plugs x 2

  • Collar x 1

  • Bracket x 1 LEFT HAND FIT

  • Bracket x 1 RIGHT HAND FIT

LEFT HAND FIT

LEFT HAND FIT LEFT HAND
FIT

RIGHT HAND FIT

RIGHT HAND FIT RIGHT HAND
FIT RIGHT HAND FIT RIGHT HAND
FIT

  • Vertical Seal x 1

  • Horizontal Seal x 1

  • Glass Panel Assembly x 1 Trim x 1

Deflector

Seal deflector faces inwards

INSTALLATION

Deflector
Seal deflector faces inwards

Bracket x 1 FLEFT HAND FIT

Bracket x 1 ERIGHT HAND FIT

INSTALLATION

INSTALLATION

WARNING
Ensure glass screen is vertical

Vertical overview

  • No.8 x 1¾” Pan Head Pozi Screws x 2
    Hardware

  • Wall Plugs x 2
    Hardware

  • Bracket x 1 FLEFT HAND FIT

  • Bracket x 1 RIGHT HAND FIT

LEFT HAND FIT

LEFT HAND FIT LEFT HAND
FIT LEFT HAND FIT

RIGHT HAND FIT

RIGHT HAND FIT RIGHT HAND
FIT RIGHT HAND FIT

Wall mounting and Fixings

Important note:
If plastic wall plugs are supplied with your product: these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice. Failure of the product due to using incorrect fixings is the responsibility of the installer.

Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualifed tradesperson if you are unsure.

Hints:

  1. General rule: U Always use a larger screw and wall plug if you are not sure.
  2. Ensure you use the recommended drill bit to match the wall plug and hole size.
  3. Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
  4. Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking.
  5. Ensure wall plugs are well fitted and are a tight fit in the drilled hole.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals