VigorSwitch G1282 Web Smart Managed Switch User Guide
- June 4, 2024
- VigorSwitch
Table of Contents
VigorSwitch G1282 Web Smart Managed Switch
Package Content
The type of the power cord depends on the country that the switch will be installed.
If any of these items is found missing or damaged, please contact your local supplier for replacement.
Panel Explanation
| LED | Status | Explanation |
|---|
SYS
| On (Green)| The switch finishes system booting and the system is ready.
Blinking (Green)| The switch is powered on and starts system booting.
Off| The power is off or the system is not ready / malfunctioning.
PWR
| On (Green)| The device is powered on and running normally.
Off| The device is not ready or is failed.
RJ45 (LNK/ACT)
Port 1 ~ 24
| On (Green)| The device is connected
Blinking| The system is sending or receiving data through the port.
Off| The port is disconnected or the link is failed.
Combo Ports 25 ~ 28 and SFP (LNK/ACT)| On (Green)| The device is connected
Blinking| The system is sending or receiving data through the port.
Off| The port is disconnected or the link is failed.
Interface| | Description
RJ 45 LNK/ACT Port 1 ~ 24| Port 1 to Port 24 are used for Ethernet connection.
SFP LNK/ACT Port 25 ~ 28| Port 25 to Port 28 are used for fiber connection.
****| Power inlet for AC input (100~240V/AC, 50/60Hz).
Hardware Installation
Before starting to configure the switch, you have to connect your devices correctly.
Network Connection
Use the Ethernet cable(s) to connect None-PoE devices to the Vigor switch. All
device ports are in the same local area network.
Rack-Mounted Installation
The switch can be installed easily by using rack mount kit.
- Fasten the rack mount kit on both sides of the VigorSwitch using specific screws.
- Then, install the VigorSwitch (with rack mount kit) on the 19-inch chassis by using other four screws.
Software Configuration
Before using the switch, perform the following steps:
- Set up a physical path between the configured the switch and a PC by a qualified UTP Cat. 5e cable with RJ-45 connector.
If a PC directly connects to the switch, you have to setup the same subnet mask for PC and the switch. Default values of the managed switch are listed as follows:IP Address| 192.168.1.224
---|---
Subnet Mask| 255.255.255.0
DHCP Client| Enabled (On)
Username| admin
Password| admin - After configuring correct IP address on your PC, open your web browser and access switch’s IP address.
The home page of VigorSwitch will be shown as below:
Customer Service
If the switch cannot work correctly after trying many efforts, please contact
your dealer for further help right away. For any questions, please feel free
to send e-mail to support@draytek.com.
Be a Registered Owner
Web registration is preferred. You can register your Vigor router via
https://myvigor.draytek.com.
Firmware & Tools Updates
Due to the continuous evolution of DrayTek technology, all switches will be
regularly upgraded. Please consult the DrayTek web site for more information
on newest firmware, tools and documents. https://www.draytek.com
GPL Notice
This DrayTek product uses software partially or completely licensed under the
terms of the GNU GENERAL PUBLIC LICENSE. The author of the software does not
provide any warranty. A Limited Warranty is offered on DrayTek products. This
Limited Warranty does not cover any software applications or programs.
To download source codes please visit: http://gplsource.draytek.com
GNU GENERAL PUBLIC LICENSE:
https://gnu.org/licenses/gpl-2.0
Version 2, June 1991
For any question, please feel free to contact DrayTek technical support at
support@draytek.com for further information.
EU Declaration of Conformity
We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan , R.O.C., declare under our sole responsibility that the product
- Product name: 24+4 Gigabit Combo Switch
- Model number: VigorSwitch G1282
- Manufacturer: DrayTek Corp.
- Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
is in conformity with the relevant Union harmonisation legislation: EMC Directive 2014/30/EU , Low Voltage Directive 2014/35/EU and RoHS 2011/65/EU with reference to the following standards Standard| Version / Issue date
---|---
EN 55032| 2015+A11:2020 class A
EN 61000-3-2| 2019
EN 61000-3-3| 2013+A1:2019
EN 55035| 2017+A11:2020
EN 62368-1| 2014+A11:2017
EN IEC 63000:2018| 2018
Declaration of Conformity
We DrayTek Corp. , office at No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan , R.O.C., declare under our sole responsibility that the product
- Product name: 24+4 Gigabit Combo Switch
- Model number: VigorSwitch G1282
- Manufacturer: DrayTek Corp.
- Address: No.26, Fushing Rd., Hukou, Hsinchu Industrial Park, Hsinchu 303, Taiwan
- Importer: CMS Distribution Ltd: Bohola Road, Kiltimagh, Co Mayo, Ireland
is in conformity with the relevant UK Statutory Instruments:
The Electromagnetic Compatibility Regulations 2016 (SI 2016 No.1091), The Electrical Equipment (Safety) Regulations 2016 (SI 2016 No.1101), and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (SI 2012 No. 3032) with reference to the following standards: Standard| Version / Issue date
---|---
EN 55032| 2015+A11:2020 class A
EN 61000-3-2| 2019
EN 61000-3-3| 2013+A1:2019
EN 55035| 2017+A11:2020
EN 62368-1| 2014+A11:2017
EN IEC 63000:2018| 2018
Copyrights
© All rights reserved. This publication contains information that is
protected by copyright. No part may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language without written
permission from the copyright holders.
Trademarks The following trademarks are used in this document:
- Microsoft is a registered trademark of Microsoft
- Windows, 8 , 10, 11 and Explorer are trademarks of Microsoft
- Apple and Mac OS are registered trademarks of Apple
- Other products may be trademarks or registered trademarks of their respective
Safety Instructions
l Read the installation guide thoroughly before you set up the switch.
- The switch is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the switch yourself.
- Do not place the switch in a damp or humid place, g. a bathroom.
- Do not stack the
- The switch should be used in a sheltered area, within a temperature range of +5 to +40
- Do not expose the switch to direct sunlight or other heat The housing and electronic components may be damaged by direct sunlight or heat sources.
- Do not deploy the cable for LAN connection outdoor to prevent electronic shock
- Keep the package out of reach of
- When you want to dispose of the switch, please follow local regulations on conservation of the environment.
Warranty
We warrant to the original end user (purchaser) that the switch will be
free from any defects in workmanship or materials for a period of two (2)
years from the date of purchase from the dealer. Please keep your purchase
receipt in a safe place as it serves as proof of date of purchase. During the
warranty period, and upon proof of purchase, should the product have
indications of failure due to faulty workmanship and/or materials, we will, at
our discretion, repair or replace the defective products or components,
without charge for either parts or labor, to whatever extent we deem necessary
tore-store the product to proper operating condition. Any replacement will
consist of a new or re-manufactured functionally equivalent product of equal
value, and will be offered solely at our discretion. This warranty will not
apply if the product is modified, misused, tampered with, damaged by an act of
God, or subjected to abnormal working conditions. The warranty does not cover
the bundled or licensed software of other vendors. Defects which do not
significantly affect the usability of the product will not be covered by the
warranty. We reserve the right to revise the manual and online documentation
and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving
- Increase the separation between the equipment and
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
- Consult the dealer or an experienced radio/TV technician for
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and This device may accept any interference received, including interference that may cause undesired operation
USA Local Representative
| Company name| ABP International Inc.
---|---|---
Address| 13988 Diplomat Drive Suite 180 Dallas TX 75234
ZIP Code| 75234| E-mail| rmesser@abptech.com
Contact Person| Mr. Robert Messer| Tel.| 19728311600
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. More updates, please visit www.draytek.com.
References
- Home | DrayTek
- GNU General Public License v2.0 - GNU Project - Free Software Foundation
- MyVigor - DrayTek
- Home | DrayTek
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>