classy leaves RED5803439 Bathroom Light Fixtures Instruction Manual
- June 17, 2024
- classy leaves
Table of Contents
- classy leaves RED5803439 Bathroom Light Fixtures Instruction Manual
- IMAGE FOR FINISHED PRODUCT:
- TOOLS REQUIRED (NOT INCLUDED):
- PARTS INCLUDING:
- ACCESSORIES ENCLOSED:
- ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Turn off power
- Make assembly
- Note: back plate (E) should be snug against the wall with knob nuts (F).
- Check everything is installed properly, then you could turn on the light.
- ORDERING PARTS
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
classy leaves RED5803439 Bathroom Light Fixtures Instruction Manual
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later
- Before you start, NEVER attempt any work without shutting off the electricity until the work is
- Go to the main fuse, or circuit breaker, box in your Place the main power switch in the “ OFF ” position.
- Place the wall switch in the “ OFF ”
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING:
- Green ground screw (1)
- Mounting plate (1)
- Back plate (1)
- Knob nut (2)
- Arm (1)
- Socket (3)
- Cloth shade (3)
- Socket ring (3)
ACCESSORIES ENCLOSED:
- Mounting screw (2)
- Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Turn off power
Before you start the installation, NEVER attempt any work without shutting
off the electricity until the work is done.
A.Go to the main fuse, or circuit breaker, box in your home. Place the main
power switch in the “OFF” position.
Place the wall switch in the “OFF”
Make assembly
Step A1: Unscrew knob nuts (F) from back plate (E), then set them aside for
later installation.
Step A2: Secure mounting plate (D) to the outlet box with mounting screws (A).
Step A3: Make wire connections
Connect wires as below wires connection shown.
PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES
TO GROUND WIRES.
Connect ground wires according to the below chart Connect wires
according to the below chart
Twist wires together with plastic wire connectors until tightly joined, and
wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in back plate (E) with the pre-assembled mounting
screws, then attach back
plate (E) to mounting plate (D) with the previously removed knob nuts (F).
Hand tighten until snug.
Note: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (D) by unscrewing the pre-assembled hex nuts and then screwing the
pre-assembled mounting screws in or out of the mounting plate until the secure length is achieved. Tighten the pre-assembled hex nuts and back to Step A4.
Step A5: Fix cloth shades (I) to sockets (H) with socket rings (J).
Install bulbs (Not included) (Please do not exceed the maximum wattage
recommended on the socket.)
Check everything is installed properly, then you could turn on the light.
Enjoy!
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and non-abrasive
soap.) Do not use abrasive materials such as scouring pads or powders, steel
wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>