classy leaves B0B3JDNKMW Chandeliers for Dining Rooms 33 Modern Gold Chandelier Instruction Manual

B0B3JDNKMW Chandeliers for Dining Rooms 33 Modern Gold Chandelier

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3.  Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

4.  Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5.  Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6.  Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.

7.  Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8.  When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9.  The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT：

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING:

(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Swivel joint (1)
(G) Knob ball (2)
(H) Tube
(I) Arm (4)
(J) Threaded ring (4)
(K) Glass shade (4)
(L) Arms assembly (1)

ACCESSORIES & QTY ENCLOSED:
(A) Plastic wire connector (3)
(B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

3.  Unscrew the knob balls (G) from canopy (E) then remove the mounting plate (C).

4. Adjust the arms (I) to the proper position.

5. 1. According to your desired hanging height to choose and use the tubes (H), then pass the fixture wires through the tubes (H), the swivel joint (F) and the canopy (E).

2. Attach the chosen tubes (H) and the canopy (E) with the swivel joint (F).
   Screw tubes (H) onto the arms assembly (L).
   Hand tighten until snug.

6. Attach the mounting plate (C) to outlet box with the mounting screws (B).

7. Make wire connections
   Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   Connect ground wires according to the below chart
   
   Connect wires according to the below chart

Connect Black or

Red Supply Wire to:

| Connect

White Supply Wire to:

---|---
Black| White
Parallel cord ( round & smooth )| Parallel cord ( square & ridged )
Clear,Brown,Gold or Black without tracer| Clear,Brown,Gold or Black with tracer
Insulated wire ( other than green) with copper conductor| Insulated wire ( other than green ) with silver conductor

Twist wires together with plastic wire connector (A) until tightly joined, then carefully tuck all wires into the outlet box. Note: be sure that no wire strands are not exposed.

8. Raise canopy (E) to ceiling and secure canopy (E) in place by knob balls (G) onto the pre-assembled threaded nipples on the mounting plate (C).
Note: The canopy (E) should be snug against the ceilingand the ball knobs (G). If not, adjust the length of the pre-assembled threaded nipples on the mounting plate assembly (C) by unscrewing the pre-assembled hex nuts and then screwing the threaded nipples in or out of the mounting plate (C) until the length is achieved. Tighten the hex nuts and back to step 8.

9. Install the bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.) Screw the glass shades (K) onto the threaded rings (J).

10. Check everything is already installed properly, then you could turn on the light. Enjoy!

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap.)
Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>