Classy Leaves A03489 3 Light Gold Vanity Light Instruction Manual

Classy Leaves A03489 3 Light Gold Vanity Light

Product Information

Product Specifications:

• Mounting plate (C): 1 piece
• Green ground screw (D): 1 piece
• Backplate (E): 1 piece
• Screw (F): 2 pieces
• Arm (G): 1 piece
• Socket (H): 3 pieces
• Glass shade (I): 3 pieces
• Socket ring (J): 3 pieces

Product Usage Instructions

1. Pre-Installation Preparation:
   Ensure you have the necessary tools as shown in the picture.

2. Assembly & Installation:

3. Remove the fixture from the carton and check all parts are included.

4. Turn off the power by switching off the main power switch and wall switch.

5. Step A1: Unscrew the grub screw (F) from the back plate (E) and remove the mounting plate (C).

6. Step A2: Secure mounting plate (C) to the outlet box with mounting screws (A).

7. Step A3: Make wire connections following the provided chart. Use plastic wire connectors and electrical tape.

8. Step A4: Align and secure the back plate (E) with screws (F).

9. Step A5: Attach the glass shade (I) to the socket (H) using the socket ring (J).

10. Install bulbs within the recommended wattage.

11. Final Steps:
    Check that everything is installed correctly before turning on the light to enjoy your new fixture.

12. Cleaning:
    Use a soft cloth to wipe the fixture. Clean glass with mild soap, avoiding abrasive materials.

13. Ordering Parts:
    Keep the manual for future reference and order replacement parts if needed. Parts can be ordered from the place of purchase using the exact wording from the illustration.

Frequently Asked Questions (FAQ):

• Q: Can I install this fixture without a licensed electrician?
  A: It is recommended to have a licensed electrician installed to reduce the risk of fire, electric shock, or injury.

• Q: What should I do if I exceed the maximum recommended wattage for bulbs?
  A: Please do not exceed the maximum wattage recommended on the socket to prevent damage to the fixture.

• Q: How should I clean the fixture?
  A: Use a soft cloth to wipe the fixture and mild soap to clean the glass. Avoid abrasive materials like scouring pads or steel wool.

SAFETY INSTRUCTION

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
4. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
5. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
6. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
7. When replacing the bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
8. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

• (C) Mounting plate (1)

• (D) Green ground screw (1)

• (E) Backplate (1)

• (F) Screw (2)

• (G) Arm (1)

• (H) Socket (3)

• (I) Glass shade (3)

• (J) Socket ring (3)
  ACCESSORIES ENCLOSED:

• (A) Mounting screw (2)

• (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B) Place the wall switch in the “OFF” position.

3. Make assembly

   • Step A1: Unscrew the grub screw (F) from the back plate (E) then gently remove the mounting plate (C).

   • Step A2: Secure mounting plate (C) to outlet box with mounting screws (A).

   • Step A3: Make wire connections
     Connect wires as below wires connecting shown below. PLEASE NOTE GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
     Twist the plastic wire connector until wires are tightly joined together, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

   • Step A4: Align the holes in the back plate (E) and the mounting plate (C), then secure the back plate (E) with the previously removed screws (F) till snug.

   • Step A5: Fix the glass shade (I) to the socket (H) with the socket ring (J).
     Install bulbs (Not included. Please do not exceed the maximum wattage recommended on the socket.)

4. Check everything is installed properly, then you can turn on the light. Enjoy!

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>