JITUO KBG2 Three Mode Mechanical Keyboard User Manual

JITUO KBG2 Three-Mode Mechanical Keyboard

Description of indicator light and battery level display screen

• Caps: Case indicator light, indicator light C
• Win: Lock&Unlock indicator light, indicator light W
• Low battery: Fast flashing below 3.3V, indicator light 188 displays numbers 0 to 100, and the displayed amount is based on the battery level.

Switch indication, knob description

1. Forced switch between Windows and Mac systems, factory default Windows system;
2. Switch between wired mode, Bluetooth mode, and 2.4G mode. Left=Bluetooth mode, middle=wired mode, right=2.4G mode, factory default wired mode;
3. Knob: Press play/pause, turn left volume -, turn right volume+

Sleep mechanism and Bluetooth name description

1. Deep sleep: After 30 minutes of keyless operation on the keyboard, it will be in deep standby mode. Bluetooth will be disconnected and hibernated, and any key will be pressed to wake up the keyboard backlight and reconnect to Bluetooth;
2. Power saving sleep: After 1 minute of keyless operation on the keyboard, the backlight turns off. Press any button to wake up the keyboard backlight and connect back to Bluetooth;
3. Bluetooth name: BT5.0 KB or BT3.0 Keyboard

Light mode FN+ | Light effect switching, 16 light effects cycle in sequence:

Button composite function

General configuration instructions

• Shaft body : Conventional
• Hot-swappable connector : Factory customized to support 5-pin shaft
• Upper cover : ABS dual color injection molding Lower cover: ABS injection molding
• Keycap : PBT
• Wire: 2M
• Matrix: full key without impact
• Lithium battery: 3000 milliamperes (according to customer requirements)
• Size: 327.27 136.27 40mm ± 0.5mm
• Weight: 770g ± 5% 16 sets of lighting effects
• Lighting: RGB
• Interface: Keywire separated type interface

Package includes

• Keyboard x1
• 2 M coiled cableX1
• Use manual x1
• Keycap puller x1

Operation of hot-swap Switch

• Step1 : Use the switch puller to clamp buckles on both sides of the switch
• Step2 : Keep pressing and pull out the switch
• Step3 : Ensure that two welding feet of the switch are straight If bend, please straighten them Careful with your fingers
• Step 4 : Ensure that the switch is aligned with the correct position and press down the switch slightly, until buckles on both sides of the switch return to the corresponding position.

FCC STATEMENT

FCC Warning StatementChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.

DONGGUAN JITUO ELECTRONIC TECHNOLOGY CO.,LTD

• ADD: Zone B, 4th floor, Building F, no 177, Wenming road(qiaotou section),Qiaotou Community, Qiaotou Town Dongguan City, China
• Postal Code: 523523 Website:www.gitoper.com Email: service@gitoper.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>