Sunco Lighting EX 2H-BLACK 2 Head LED Exit Sign User Manual

Sunco Lighting EX 2H-BLACK 2 Head LED Exit Sign

Product Specifications

• Voltage: 120V-277V
• Wattage: 3.3W
• Power Factor: 0.48
• CRI: 80
• Weight: 1.61lbs
• Housing Material: ABS+PMMA
• Dimmable: No
• Beam Angle: 120 degrees
• Lumens: 300LM
• IP Rating: IP20
• Battery: 3.6V 1000mAh NI-MH Battery
• Power Source: Battery
• Amps: 0.32A
• Warranty: 3 Years

Product Usage Instructions

Before You Start – Safety Information

• Before installation, ensure you have the necessary tools: drill, pliers, screwdriver, and ladder.
• Make sure to install the junction box before proceeding with the exit sign installation.
• Use only specified lamps to prevent damage or unsafe conditions.

Installation Guide

Step 1:

• a. Turn off the circuit breaker before installation.
• b. Open the housing of the exit sign by using a flathead screwdriver in slots on top. Alternate sides to unsnap the entire faceplate. Pull off the faceplate & set it aside.
• c. Remove mounting components (wrapped in plastic for shipping) from the housing. Set aside.

FAQ

Common Troubleshooting

• If you are facing any issues with your product, please contact our customer support at support@sunco.com or call 844-334-9938 for assistance.

What’s in the Box?

Exit Sign

Components

What You Need

Get Your Gear

• IMPORTANT: Before exit sign installation, install a junction box in the ceiling or wall. When re-lamping, use only lamps specified in the exit sign. Using other lamp types may result in transformer damage or unsafe conditions.
• The battery in this unit may not be fully charged upon unboxing. After electricity is hooked up to the unit, let the battery charge for at least 24 hours. It is then ready for normal operation. Unused wires must be capped with a wire nut.

Safety Information

• Turn off the circuit breaker before installing this fixture.
• Suitable for use in damp environments at temperatures ranging from 32°F to 104°F. Not for use where directly exposed to water.
• Not compatible with photo controls.
• Not compatible with occupancy sensors.
• Not compatible with 3rd party sensors.
• Not compatible with dimmers.
• Not compatible with timing devices.
• All electrical connections must be under local and National Electric Code (N.E.C.) standards.
• Please review the installation manual carefully before proceeding. Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
• WARNING: Cancer & Reproductive Harm- www.P65Warnings.ca.gov

FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation. Please review all instructions carefully before installation.

Dimensions

Installation Guide

STEP 1

• a. Turn off the circuit breaker before installation.
• b. Open housing of exit sign using flathead screwdriver in slots on top. Alternate sides to unsnap the entire faceplate. Pull off the faceplate & set it aside.
• c. Remove mounting components (wrapped in plastic for shipping) from the housing. Set aside.

STEP 2

• a. Unwrap canopy and mounting hardware from plastic packaging.
• b. Snap two support connectors in the provided slots. These will connect the canopy mount plate to the top of the housing.

STEP 3

• a. Pop out top knockout. There are two slots. Feed lead wires through the hole.
• b. Secure wires with a wire guide.

STEP 4

• a. Align the trim plate to screw holes on the back of the canopy mount plate. Turn over. Secure the trim plate with 2 provided screws.
• b. Feed lead wires (from face to back) through the canopy mount plate & trim plate. Snap canopy mount plate onto exit sign housing.

STEP 5

• a. Connect exit sign lead wires to AC input leads in the junction box (not included) & cap off unused wires with wire nuts.
  b. Feed the excess wire into the J-box. Secure canopy mount with exit sign using included screws. Connect a battery to the PC board by plugging the wire into a socket.

STEP 6

• a. Reattach the faceplate. Ensure all four corners have snapped together properly. Knock out direction arrow(s), as appropriate for your light fixture location.
• b. Turn on power. A battery may need 24 hours to charge before the light fixture is used for emergency purposes.

Product Details

Wiring Diagram

Specifications

Common Troubleshooting

• Feeling in the dark about an issue with your product? No worries! Our troubleshooting section is here to shed some light and provide you with easy-to-follow solutions for any problem.
• If you still need some assistance, please feel free to contact us with any questions. Our team of lighting experts is happy to help brighten your day.

Customer Support

Warranty Policy

• This product is covered by our industry-leading 3-year warranty. It gets even better – scan the QR code for 2 extra years of protection!

30-Day Return Policy

• At Sunco, we value our customers and stand by the quality and performance of our products.
• If you are not completely satisfied with your purchase, we accept returns within 30 days of your purchase date.

Customer Service

• Our Los Angeles team of lighting experts is here to assist you with all your needs!
• Contact   us at: Email: support@sunco.com
• Call or Text:844-334-9938
• support@sunco.com
• 844-334-9938

Documents / Resources

| Sunco Lighting EX 2H-BLACK 2 Head LED Exit Sign [pdf] User Manual
EX 2H-BLACK 2 Head LED Exit Sign, EX 2H-BLACK, 2 Head LED Exit Sign, LED Exit Sign, Exit Sign
---|---

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>