FeeLTEK AS2059 LCD Expansion Dock Instruction Manual
- May 15, 2024
- FeeLTEK
Table of Contents
FeeLTEK AS2059 LCD Expansion Dock
Product Information
Specifications:
- Compliance: Part 15 of FCC Rules
- RF Exposure Requirement: General
- Radiation Exposure Limits: FCC approved for uncontrolled environment
- Safety Distance: Minimum 20cm between radiator and body
Product Usage Instructions
Installation:
1. Place the device in a location where there is at least a 20cm distance between the radiator and your body.
2. Ensure that the device is set up on a stable surface to prevent any accidental falls.
Operation:
1. Power on the device according to the manufacturer’s instructions.
2. Follow the specific usage guidelines provided in the user manual for optimal performance.
Maintenance:
1. Regularly clean the device using a soft, dry cloth to remove any dust or debris.
2. Avoid exposing the device to extreme temperatures or moisture to prevent damage.
FAQ
Q: Can I modify the device without voiding the warranty?
A: Any changes or modifications not approved by the manufacturer could void your warranty and authority to operate the equipment. It is recommended to consult with the manufacturer for any alterations.
Q: What should I do if I experience interference during operation?
A: If you encounter interference while using the device, try adjusting its placement or moving it to a different location. Ensure that there are no electronic devices causing interference nearby.
Hello! Thank you for purchasing and using the TSL LCD Smart Control Dock.
Please read this user manual carefully before use And fully understand the
usage conditions and methods. Attention: The protection level of this product
is IP55, which completely prevents the intrusion of foreign objects. Although
it cannot completely prevent the intrusion of flying dust, a small amount of
flying dust intrusion will not affect the function of this product. It is
necessary to prevent water splashing from all directions from entering the
product Damage caused internally to avoid faults and short circuits caused by
water intrusion. Warning: This product is an auxiliary product for vehicle
expansion. Please use and operate this product while ensuring safe driving to
ensure your driving and vehicle safety!!!
Special safety reminder: The ACC acceleration mode button must be operated
while ensuring driving safety.
Introduction to panel functions
Power input: DC5V
Charming interface output: USB-A interface TYPE-C interface
- Knob (function selection)
- Atmosphere light strip
- Automatic air conditioning switch button (long press for 2 seconds to fold and open the rearview mirror)
- USB charging port
- Window lock switch button (long press for 2 seconds to move the passenger seat forward)
- TYPE-C charging port
- Glove box open button (long press for 2 seconds to move the passenger seat back)
- Mode Switching (CHILL Comfort Mode STD Standard Mode)
- Atmosphere light strip
Introduction to knob functions
LCD display knob. When the logo is displayed, rotate the knob to increase or decrease the air conditioning wind speed. Press to select, and rotate the knob to adjust the wind speed, volume, up and down curves, front and rear passenger movement, front and rear passenger tilt, child lock, roof light, and folding earMore auxiliary functions such as Rear AC settings
Installation instructions
- Use a rocker panel to remove the passenger seat sealing strip
- Use a rocker panel to remove the two decorative panels marked by the arrow on the passenger side
- Use a rocker panel to remove the identification. 3Remove the decorative panel from the plastic fixing column
- Use a rocker to remove the identification 4 foot pad, velvet cloth, and plastic fixed column
- Use a screwdriver to remove the screw under the passenger seat decorative panel and take the decorative panel,
- Thread the terminal wire of the passenger side box in the modified wiring harness under the seat, connect the passenger side control box, and secure it
- Connect the modified wiring harness to the original passenger seat control panel
- Connect the modified wiring harness to the original passenger side control wiring harness and connect it to the protocol box
- Attention: Some models of the original vehicle host terminals have transparent rubber sleeves inside the terminals that need to be removed, otherwise the modified wiring harness terminals cannot be inserted properly.
- After routing the modified wiring harness, follow the steps to restore it
- Insert two USB cables into the modified product, connect them to the USB in the storage box, and after powering on, the product will automatically connect to the modification protocol. At this time the original car functions can be controlled
- Tear off the double-sided tape, and the product enters the storage box diagonally, close to the cup holder. The modification is completed
FCC statements
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>